HartwanCopper tubeWeekly review

for some important parts, at this time, the utilization rate of materials is also low. Common sense: copper pipes for air conditioners are mainly used for conveying liquid, gas and steam; Boiler pipes and steam transmission pipes are used for the piping, structure and steam transmission of steam boilers, including the transmission of high-temperature and high-pressure steam; Structural pipe, widely used in aviation, automobile, tractor and other industrial sectors; Pipe for petroleum industry, mainly used for oil and gas exploitation, such as casing,Hartwan316L stainless steel coiled plate, and pipe for petroleum refining and processing; Pipe for mechanical manufacturing,HartwanComposite copper bar, which is used to manufacture the race of ball bearing, the plunger, rotating shaft and body of air pump and hydraulic pump; High pressure vessel, used for manufacturing bottles, boilers, shells, etc. At present, copper pipes for air conditioners are mainly used in three aspects in practical applications. First, medical copper pipes are widely used in industrial plants, high-rise civil buildings, municipal engineering, oil platforms, bridges, railway vehicles and other fields. Because of their good plasticity, high structural stability and strong resistance to natural disasters, they are particularly suitable for building structures in earthquake prone areas. Second, the air conditioning copper pipe has high tensile strength and toughness high buildings, bridges and other steel structures have good cold bending performance and welding performance, and the section size and surface quality are well controlled, large bridge construction, mechanical manufacturing, air conditioning copper pipes are mainly used to make transmission line towers, microwave transfer station towers, construction crane towers, elevator supports, etc. The idea is to use weather resistant steel when making iron towers to meet the service conditions of both normal temperature and low temperature. PPM pressure roll piercer used for air conditioning copper pipe tapping rolling is not replaced by inclined roll piercer used for square steel billet. The advantage of the conical piercer is that it has the consequence of rotary euphemism casting and the of restraining the shear deformation of the square circumference and the square back. Therefore, it can prevent the defects outside the steel pipe. It can be used for the perforation of agricultural materials, especially not for the reaming and fat wall perforation. When using a general piercer, the wall thickness/pitch diameter ratio (T/D limit is about 6%, while when using a square cone piercer, the T/D limit can be 2%. Tianjin Precision Steel Tube Factory will give you a brief introduction.

The degreased copper tube is made of oxygen free copper rod, which has good processing characteristics and can be punched, bent and other process design requirements. The surface can be subject to anti-corrosion treatment, such as nickel plating, tin plating, zinc plating, etc. The surface anti-corrosion can reach 72 hours of fog test. The surface tin plating is environment-friendly lead-free tin, and the surface tin layer supports soldering. T2 degreased copper tube is mainly used for communication cabinet, transformer, charging pile, box type substation and other electrical facilities. The copper bar is harder than the plastic pipe and has the degree of common metal (the strength of the cold drawn degreased copper pipe is equivalent to that of the steel pipe with the same wall thickness). It is not easy to corrode and is resistant to high temperature and high pressure. It can be used in various applications. The main material of copper bar is copper. The melting point of copper is as high as 1083 ℃, and the temperature of hot water can be ignored for degreased copper pipe, so as long as it is used correctly, there is no need to worry about safety. When choosing to decorate the house, few people ask about the water supply pipe of the house. In fact, the material of water supply pipeline will greatly affect people's health. T2 copper tube has strong capacity. Escherichia coli in the water supply will not continue to breed in the degreased copper tube, and more than 99% of the water will disappear after entering the degreased copper tube for 5 hours. This biological characteristic is that there is a small amount of copper ions dissolved in water in the degreased copper tube, and copper ions have a strong ability. Copper and zinc plating can avoid rusting and show a zinc protective film to metal materials. The conductive metal material repair and color enhancement care agent I can generate the thickness of the metal material epoxy protection layer and the pipeline cathodic protection layer, which can resist extreme weather and is suitable for the long-term surface of metal materials. The actual effect of salt and water corrosion resistance is good. The copper bar tin plating can prevent the air oxidation of the copper bar and the connection surface of the copper bar. In addition, the melting of metal tin and copper will produce aluminum alloy, the conductivity of metal tin is good. The purpose of copper and tin plating: effectively prevent copper from becoming verdant due to moisture, and also prevent copper from oxidizing/sulfurizing and blackening and affecting electricity. The service life of the tinned copper tube is several times or even more than ten times which greatly increases the service life of the copper and plays a considerable role in protecting the copper. The of tinned metal surface treatment on copper bar is to avoid air oxidation. As the air in industrial production air, marine climate or cold air is easy to turn black or produce copper green when oxidized, the copper bar surface shall be tinned for the total area, the resistance and conductivity of the steel bar lap surface.With the continuous development of industry, the demand for plastic coated copper tubes is gradually increasing. Then how to apply wood grain paint on alloy pipes. Wood like paint is a kind of wood like paint. It is used for spraying plastic coated copper pipe and its process flow. Plastic coated copper pipe is mainly used to manufacture high-pressure alloy pipe for heating surface of water tube boiler with high pressure and above. In the morning market, the mainstream spot price quoted by Lianzhong was 7900-7950 yuan/ton, and the tax inclusive base price quoted by Hongwang and Chengde was 8070-8150 yuan/ton. On a month on month basis, part of the producing areas recalled 50 yuan, and the mainstream tax inclusive base price in the market changed from strong to weak in the 7900-8100 plastic coated copper pipe supply and demand relationship. It was difficult for the price of plastic coated copper pipe in the Guangzhou market to fall sharply this week. Second, plastic coated copper tubes are widely used in superheaters, headers and main steam ducts of domestic HP, UHP and subcritical power plant boilers. Third, large diameter pipes are mainly used as headers and main steam pipes with steam parameters below 565 ℃.

Hartwan.The difference between hard copper tubes and soft copper tubes in use Hard copper tubes can only be used as straight tubes and cannot be bent. Therefore, they are generally used in power plants, and places where the connection points are far away and do not need to be bent. Compared with soft copper tubes, the price of hard copper tubes will be lower. Although the name of the soft copper tube is soft tube it can also be used as a hard tube, so the soft copper tube is used in more places, as well as in a coiled tube way. The length of the copper tube can be longer if the coil is used. If the connection point is longer, it can be cut randomly according to the length, so as to prevent leakage when welding the copper tube. Soft copper pipes are used in many refrigerators, air conditioners and other places where bending pipes are needed. When we use copper, we need not consider the preservation problem unless we buy a small amount at home. For example, large manufacturers use copper units to buy a large number of copper pipes once, so there will be a problem. I believe some people do not know how to store unused copper materials, all readers here have a clearer understanding of the automotive air conditioner copper tube. If you are interested in this product, please refer to more relevant contents. Suitable site and warehouse shall be selected for the storage of seamless air conditioning copper pipes: The site or warehouse for steel storage shall be located in a clean and well drained place away from factories and mines that produce harmful gas or dust. With the rapid development of economy, the number of cars is also fast. Nowadays, people can't live without cars. So we know what role the copper tube of automobile air conditioner plays in cars.

.Now let me talk about the damages that are easy to occur on the surface of the copper tube. In order to prevent the accumulation of process agents or products and/or dirt, scratches and other rough surfaces, mechanical cleaning must be carried out. If the copper pipe is heated to a certain high temperature in the air during welding or grinding, chromium oxide heat return color will appear on both sides, lower surface and bottom of the weld. The color after tempering is thinner than that of the oxidation protective film, and is clearly visible. The color depends on the thickness. The thicker oxide can be found in the rainbow color, blue, purple to brown. It is usually black. It is caused by being at high temperature or being at high temperature for a long time. When any of these oxide layers exist, the chromium content on the metal surface will, and the corrosion resistance of these areas will. In this case, it is not only necessary to heat temper the color and other oxide layers, but also to clean the chromium poor metal layer under it. Free iron on the surface of t2 copper tube will rust, causing corrosion of stainless steel. Therefore, the powder that must float can usually be removed together with the dust. Some are very sticky and must be treated as embedded iron. In addition to dust, there are many surface iron sources, including cleaning with ordinary carbon steel wire brush and shot peening with sand, glass beads or other abrasives previously used on ordinary carbon steel low alloy steel or cast iron, or regrinding non stainless steel products attached to copper pipe components and equipment. If there is no protection during cutting or hoisting, the wire ropes, slings and iron on the working surface can easily be embedded or dirty the surface. The copper tube shall be boiled in boiling water for 30 seconds before cold treatment. The effective internal stress is about 15%, and the residual austenite reaches the effect. Then, the cold treatment can be carried out as usual. Of course, the second suggestion is to choose the normal treatment at minus 60 degrees, the retained austenite will be rapidly transformed into martensite, but it cannot be transformed. Through experiments, it can be found that there will be about 2% of retained austenite. At this time, the air conditioning copper pipes need to be taken out and put into hot water for heating, which can effectively heat about 40% of the cold treatment stress. Tempering and cold treatment should be carried out as soon as possible after gradual heating, and most of them can avoid cracks as soon as possible, so as to ensure that the products will not deform in later use and facilitate daily storage. The transformation characteristics of the area of each layer of the copper tube during empty drawing affect the asymmetry of the deformation of the metal material. One of its characteristics is that the natural widening of each layer along the wall thickness is not consistent. Of course, the external layer of the copper tube is less, the internal surface layer of the copper tube is larger, and the natural widening of the middle layers is slow from the external layer to the internal surface layer.The technical level of degreasing copper tube for mechanical equipment With the substantial improvement of the manufacturing level of mechanical equipment and the degree of control automation in China, there is still some gap between the technical level of domestic degreasing copper tube production line and the products of foreign counterparts. After years of reform and opening up. The quality of all aspects of degreased copper pipe has also risen by several grades, significantly narrowing the quality gap with the imported production line. The aluminum hose production line and aluminum can production line developed and produced by the company break the technological monopoly of foreign companies, can provide stable and reliable production equipment for domestic and international markets and make great contributions to the aluminum packaging industry. With the continuous improvement of people's living standards, there will be more and more demand for degreased copper tube products, and its market potential is huge. Problems such as incomplete penetration, deformation, cracks and air holes are easy to occur during the fusion welding of degreased copper tubes. Compared with fusion welding, wood is not melted during brazing, which reduces the impact of large thermal conductivity of base metal on welding quality, prevents the formation of incomplete penetration, reduces the tendency to produce pores and cracks, and ensures the performance of weld. Because the base metal is not melted, the structure and properties of the base metal are almost unchanged, so that the original service properties of the base metal can be maintained.

The editor of this website of t2 Medical Copper Tube Company said that if there is no table, they can only stand to eat and probably enjoy food in other places. In the catering industry, there are various kinds of tables, and all kinds of tables are available. There are wooden tables and medical copper controlled tables. This table controlled by red copper in Chinese medicine is most common in large canteens such as schools, while wooden tables can often be found in small restaurants as one of the steel products of medical copper tubes. As his name is common, medical copper tubes have the ability to prevent rust. In the catering industry tables made of medical copper tubes have many advantages. Next, the teacher of Medical Copper Tube Consumption Co., Ltd. will introduce you to the master. The medical copper tube table is easy to see in the large canteen. This kind of canteen is extremely large, and the number of tables is amazing, so it is extremely difficult to settle accounts. If a wooden table is used, it will cost a lot of money, and it will also take a lot of work to settle after eating.

Four in one formula and process conditions Preparation of solution Take formula 1 as an example: mix the calculated amount of water for zinc oxide into a paste slowly add it into the calculated amount of phosphoric acid under stirring until it is completely dissolved, then add zinc nitrate and tartaric acid, dilute it with water to 2/3 of the total volume, add sodium alkosulfonate and OP emulsion, and add titanium sulfate. After all materials are added, dilute them to the total volume, stir them to make the solution even, cool them to room temperature, put a large amount of iron filings in the solution, and soak them for 2-3 days to make them contain enough ferrous ions. When the content of ferrous ion reaches above 7g/L, adjust the free acidity and total acidity of the solution to the specified value, and then the solution can be used at elevated temperature. When the ferrous ion reaches the above value, the phosphating speed is fast, the solution is stable, and the phosphating film is fine and dense. During operation, attention shall be paid to controlling the temperature. If the temperature is higher than 70 ℃, the degreasing technology of degreased copper pipe. How to make degreased copper pipe? The process flow of degreased copper tube? What are the characteristics of degreased copper tubes? Use of degreased copper tube? There are too many questions. Let's solve them at once. Everyone knows the copper tube. Nitrate reacts easily. The heater should be installed on the two walls of the tank, not on the bottom of the tank, to prevent local overheating. Stainless steel pipe or iron pipe should be used for heater, and lead pipe or copper pipe should not be used to avoid contamination of solution by impurities. What is degreased copper pipe? &The advantages of degreased copper pipe's comprehensive treatment of grease, rust removal, phosphating and passivation are described. This comprehensive treatment process can simplify the process, reduce the work area, save equipment costs, shorten working hours, improve labor productivity and reduce costs. This method can only be used in the occasions where the requirements for coating quality are not high.However, in actual production, due to the amount of oil contamination, light and heavy rust, the consumption rate of each component in the solution is different, so attention should be paid to adjustment and control to maintain its due role. What is the degreasing copper tube? &I have roughly known the degreasing methods of degreasing copper tubes: solvent degreasing, alkali degreasing, ultrasonic degreasing, high pressure hot water degreasing, electrolytic degreasing, etc. 1 Solvent degreasing: use degreasing solvent to dissolve the oil on the surface of red copper pipe, collect it together into a container, volatilize, collect and reuse the volatile solvent, and separate the pollutants from the circulation system. This method was used in the early stage, which has problems such as low cleaning efficiency, difficult maintenance, and environmental pollution. In recent years, many kinds of surfactants have been developed.

The large diameter coated medical copper tube can deform to prevent the risk of ductile damage; The medical copper tube has sufficient plastic deformation, and the medical copper tube is capable of deformation. It is stipulated that the plastic deformation and ductility of medical copper tubes are good. Good plastic deformation can ensure that the structure can have significant deformation before destruction. In some peak periods of the structure, the tectonic stress will be redistributed, which makes the tectonic stress spread gently. Good ductility indicates that under dynamic and static loads, more kinetic energy should be digested and absorbed when the structure is destroyed, which is the risk water of ductile destruction. For the structures with plastic deformation design scheme and the structures in disaster areas, the size of the deformation working capacity of medical copper tubes has a particularly critical practical significance. 3 Production and processing characteristics of medical copper tubes. It can be integrated with cold and heat treatment, and will not cause great harm to compressive strength, plastic deformation and ductility due to such production and processing. 4 Weldability of medical copper tube. The welding of medical copper tube is a rapid heating and cooling process. The metal materials in the welding and heat affected zone need to go through heating and melting, cooling and crystallization, and solid state change in a very short time. The industry trend is a kind of medical copper tube. Because there is no seam in the middle, it has more advantages in strength. Medical copper tubes have many different s in practical application, medical copper tubes have the same tensile strength, torsional strength, and tensile strength, and their net weight is relatively light. One is plastic copper tubes cut for social and economic development, which are widely used in the production and processing of spare parts and mechanical parts, such as oil drilling equipment, rotating shafts bicycle frames, and steel medical copper tube frames used in engineering construction. This kind of welded medical red copper pipe is developed under the special conditions that the temperature is all over and the composition is extremely unbalanced. After this kind of welding, it can produce detailed welding joints to maintain special performance indicators, which is the specified weldability. 5 Performance of medical copper tube. It refers to the service life of medical copper tube. The production and processing of annular parts with medical copper tubes can achieve the utilization rate of raw materials, simplify the production process, save raw materials and manufacturing hours, such as needle bearing throw rings, hydraulic jack sleeves, etc. At present, medical copper tubes have been widely used for production and processing. Disadvantages of medical copper tubes: medical copper tubes are also indispensable raw materials for various strategies. Drums must be produced and processed by medical copper tubes. Medical copper tubes can be divided into round medical copper tubes and profiled steel according to their different cross-sectional areas. Due to the large circle area under the same diameter specification, the annular pipe can be used to transport many large diameter medical copper pipes. Large diameter coated medical copper pipes are widely used in tap water, natural gas, petroleum, chemical industry, communication, power, marine and other engineering fields. There is no solvent in the coating and no leakage, so it will not pollute the medium transported, thus ensuring the purity and hygiene of the fluid. The temperature range from - 40 ℃ to+80 ℃ can be used alternately in cold and hot cycles, without aging and cracking, so it can be used in cold areas and other harsh conditions. When processing medical copper tubes the medical copper tube factory will use pickling, which is an indispensable part of most medical copper tubes, Pickling process is the treatment after removing surface oxide scale (Carbon steel - stainless steel - lime saponified phosphorus, butter, oil, copper and aluminum pipes - and the old ones, and then wire drawing processing. Then what are the points to be noted when washing? 1 When washing the medical copper pipes, they need to be carried out in the flowing clear water tank, so as to avoid secondary pollution. When washing, the medical copper pipes need to be fully immersed in water. At this time, the sling should be relaxed, and it can be lifted up and down three to four times. If the medical copper tube is not acid resistant, the surface may be oxide and oil, and the phosphating solution cannot remove nuclear energy. However, after acid washing of medical copper tubes, water washing is also required. 2 When the medical copper tube is washed, the water in the medical copper tube needs to be cleaned to avoid water corrosion and oxidation of the medical copper tube. Therefore, it is necessary to carry out solvent treatment as soon as possible. 4 When the medical copper tube is washed, the iron salt content must be controlled within a certain range, and it cannot exceed the standard, otherwise the medical copper tube may be damaged.

After the pipe is cleaned, the welding flux and flux shall be immediately applied to the interface and the bayonet clearance. Sufficient flux shall be thinly coated on the mating surface and assembled immediately, it is an improved spray type passivation box for t2 copper pipe production line. The installation step of the connection structure 100 between t2 copper pipe and aluminum bar belongs to the improvement of the spray type passivation box structure for t2 copper pipe production line. The passivation solution spray box is set above the side of the passivation solution box, the passivation solution spray box with downward sloping bottom is connected with the inlet of the passivation solution box by the outlet set on the box wall at the bottom of the inclined bottom the inlet of the passivation solution box is located on the box wall above the passivation solution box, the upper side of the passivation solution box is installed with a passivation pump, and the inlet pipe of the passivation pump is connected with the passivation solution box, The outlet pipe of the passivation pump is connected with the upper port of the passivation liquid spray box. With reasonable structure and convenient operation, it is convenient for operators to add passivation liquid to the passivation box, clean colloidal crystals at the bottom of the passivation box, avoid equipment blockage avoid crystals adhering to the zinc layer on the surface of galvanized pipe, and improve the surface quality of galvanized steel pipe.

production costs.Plastic coated copper pipe is one of the safe carbon fiber products. Its specific content is a new structural composite building decoration material that can be produced according to the development trend of production and manufacturing by using a glass fiber as the synergist and resin as the adhesive based on the application of full intelligent technical automatic control system equipment.

Plastic coated copper pipe is one of the safe carbon fiber products. Its specific content is a new structural composite building decoration material that can be produced according to the development trend of production and manufacturing by using a glass fiber as the synergist and resin as the adhesive based on the application of full intelligent technical automatic control system equipment.

The medical copper tube 6 is superior to the exterior wall hanging plate decorative building materials. It will be affected by microorganisms in the air all year round, accelerating the loss of its service life. 7 If the wall interface is not properly treated, the board surface also needs to be treated with interface mortar, and the later maintenance work must be done well. 1 Place it in the rainproof shed and do not place heavy objects on the surface.

Manufacture gear, shaft sleeve, worm gear and other high-strength wear-resistant parts and high corrosion resistance elastic components. Key points of semi continuous casting process for copper tube: The copper tube has strong air absorption, easy oxidation and slag formation, large solidification shrinkage, poor thermal conductivity and other casting properties, and poor casting performance; Before casting, some alkaline earth metal compounds, such as Na3A lF6 and NaF mixture, are used as slag removers to purify the copper liquid which is effective for improving the purity of liquid metals and the crystal structure of ingots. The pouring temperature of copper pipes is generally 1120~1180 ℃, and the pouring temperature of large-sized ingots is generally lower. The casting speed of the copper tube is low, and the metal level in the mold can be cast in an open flow manner without any protection; The melt needs to enter the mold through the hole at the bottom of the funnel. The design of funnel aperture should meet two conditions at the same time: one is to ensure the flow matching the casting speed; Second ensure that the liquid level in the funnel is always kept at a certain height, so that the scum on the liquid level cannot flow into the crystallizer from the funnel hole; The copper tube ingot is easy to produce air holes and concentrated shrinkage cavities. At the end of pouring, the joint coating must be carefully carried out to avoid concentrated shrinkage cavities in the ingot. The red copper tube is a bar shaped object made of copper and zinc alloy, named after its yellow color. Copper content is 56%~68% brass, and its melting point is 934967 degrees. Brass has good mechanical properties and wear resistance, and can be used to manufacture precision instruments, ship parts, gun casings, etc. Different zinc content also has different colors. For example, when the zinc content is 18%, 20% will be red and yellow, while when the zinc content is 20% 30% will be brown and yellow.

Discount.Air conditioning copper pipe is a common metal material in daily work of industrial production. The conductivity, heat conduction and corrosion resistance are excellent, and the W shape trend of air conditioning copper pipe is depressed due to the high copper content. Good machinability, fusion welding and brazing are very good. The cutting of air conditioner copper pipe is a very energy consuming work. The following items need to be paid attention to in order to cut neat and beautiful parts. Before cutting the air conditioner copper pipe, the cutting machine should carry out calibration and other operations. You can try to use scrap metal first to prevent machine problems from causing me to cut off defective products.

The simplest way is to use copper cleaner. Brass, red copper, bronze, etc. can be used. Oil stains, oxide layers, etc. on the surface can be cleaned with copper cleaner first.

The operation is very convenient. The forward and reverse switches are set on the front panel and can be toggled up and down. The advantage is power saving (efficiency 90%, time saving (only two thirds of the time of the original rectifier, or even shorter), material saving (at the same time raw materials can be saved 30%, and efficiency is high (more than one third of the output value of each savings). The degreased copper tube has less deformation resistance and is easier to form. The original color of copper should be orange or rose, but it is easy to oxidize into purple in the air,HartwanTinned red copper bar, so it is also called degreasing copper tube. In terms of conductivity and thermal conductivity, brass rod has no hardness of copper rod, and degreased copper tube is inferior to copper wire. The defatted copper tube Huangtong brand has its own advantages and disadvantages, but the differences are also luminous points. Can affect people's lives, because it can be applied to different aspects. As the conductivity of copper is better than aluminum, copper bus is widely used in electrical equipment, especially in complete power distribution equipment. The UVW phase bus and PE bus in the general distribution cabinet are copper bus; In use, copper bus bars are generally marked with colored letters or painted with colored paint.

Hartwan.In addition, quartz sand is used as sand intercalation layer on the long distance uniform pavement in the middle of chemical fiber. Its wall thickness and structure are reasonable, and the plastic coated copper pipe laying process stipulates that the plastic coated copper pipe is a non-metallic material pipe with light quality, high strength and corrosion resistance. The glass fiber with epoxy resin based weight relief is coiled on the rotating hollow floor step by step according to the processing technology. It can make full use of the efficacy of raw materials, achieve the goal of applying compressive strength, improve the strength and stiffness, and ensure the reliability and stability of t2 copper tube. FRP sand pipe is accepted by many customers because of its excellent resistance to solvent erosion, light weight high strength, non fouling strong durability, long service life compared with ordinary seamless steel pipe, low comprehensive project cost, convenient installation, reliability and other advantages. Plastic coated copper pipe is used in: gray and black metallurgy industry, nonferrous plate metallurgy industry, power industry, coal engineering, petroleum industry, chemical industry, electromechanical engineering industry, cotton textile, vehicle and motorcycle processing and manufacturing industry, railway line for industrial production, shipbuilding, engineering construction, light industry, food industry, electronic industry, power, culture and art, sports culture and game entertainment, agriculture and animal husbandry, commercial services, Diagnosis, treatment and health and its national defense and civilian industries.

Generally speaking, it is basically guaranteed to purchase t2 copper tubes with reliable quality. If long-term and large-scale procurement is required, it is recommended to go to the manufacturer for field inspection to determine the basic performance and quality of t2 copper tubes before large-scale mold procurement. The position of grid accessories plays a very important role in the whole construction process. The products with high cost performance and good performance certainly have a great assistance effect for the implementation of the project. In addition, it is also beneficial to the application of the middle and later stage of the forming project. There are high regulations for the performance of the grid. How about the corrosion resistance of the grid accessories? The performance of durable products such as grid and grid accessories needs to meet certain technical standards. The anti-corrosion performance of grid production and processing must be good. For manufacturers, it is necessary to improve technology and consider the performance requirements of today's construction projects. In fact, the anti-corrosion performance of accessories is not very good. It is necessary to take protective measures in the production and application process to reduce product erosion, Only by maintaining the overall reasonable layout of the grid products can we ensure the long-term performance advantages. Many technologies are required in the whole process of production and manufacturing of space truss accessories. The production and manufacturing staff should ensure the performance advantages when carrying out production and manufacturing of products. The production and processing of space truss should improve its corrosion resistance, compression resistance and strength to ensure that qualified products are produced by the original factory.

In particular, it is an improved spray type passivation box for t2 copper pipe production line. The installation step of the connection structure 100 between t2 copper pipe and aluminum bar belongs to the improvement of the spray type passivation box structure for t2 copper pipe production line. The passivation solution spray box is set above the side of the passivation solution box, the passivation solution spray box with downward sloping bottom is connected with the inlet of the passivation solution box by the outlet set on the box wall at the bottom of the inclined bottom, the inlet of the passivation solution box is located on the box wall above the passivation solution box, the upper side of the passivation solution box is installed with a passivation pump, The outlet pipe of the passivation pump is connected with the upper port of the passivation liquid spray box. With reasonable structure and convenient operation, it is convenient for operators to add passivation liquid to the passivation box, clean colloidal crystals at the bottom of the passivation box avoid equipment blockage, avoid crystals adhering to the zinc layer on the surface of galvanized pipe, and improve the surface quality of galvanized steel pipe.