Guihu1.5mm stainless steel 304 plateRecent industry trends

150 ~ 250 ℃,GuihuStainless steel coil manufacturer, time 20 ~ 30min) → Molten salt treatment → Water quenching → Hot water wash. Molten salt treatment is not suitable for assemblies with weld gaps or curls. When parts are taken out of the molten salt furnace and water quenched, a stream of alkali and salt mist will be splashed. Therefore, deep well type anti splashing water shall be used during water quenching

However, why do so many people have to accept the fact that they don't like the stainless steel tubes? Here is why stainless steel tubes need packaging bags.

Guihu.The requirements for weldability and weldability vary from product to product. A kind of tableware usually does not need welding performance, and even includes some pot enterprises. However, most products require good welding performance of raw materials, such as class II tableware, thermos cup,Guihu201 stainless steel coil manufacturer, steel pipe, water heater, water dispenser, etc

Molten salt has strong oxidizing power low melting point and small viscosity. In the production process, only the sodium halo content is not less than 8% (WT). It shall be treated in a salt bath furnace at 450 ~ 470 ℃ for 5 minutes for ferritic stainless steel and 30 minutes for austenitic stainless steel. Again,

.Type a pipe is also a very competitive water supply pipe, which will improve water quality and improve people's life

CO2 welding what does CO2 welding mean? It is a gas shielded arc welding using carbon dioxide as the protective gas,GuihuPrice of 304 stainless steel rod, which is fully called carbon dioxide gas shielded arc welding.

Wash with organic solvent. The trademark on the surface of stainless steel plate can be cleaned with alcohol and organic solvent, but the oxidation rate will be affected by inherent factors such as environment and product morphology.

Inspection, etc.

equipment maintenance .Molten salt has strong oxidizing power, low melting point and small viscosity. In the production process, only the sodium halo content is not less than 8% (WT). It shall be treated in a salt bath furnace at 450 ~ 470 ℃ for 5 minutes for ferritic stainless steel and 30 minutes for austenitic stainless steel. Again,

When using this method, it should be noted that the water-soluble paper should be double-layer and must be pasted well, otherwise the water-soluble paper may be damaged and fall off, resulting in the cutting of the weld crater and re welding, which can not guarantee the welding quality, but also seriously affect the welding quality

The construction period has been shortened, so the welding shall be strictly checked and water-soluble paper shall be pasted before welding.

Corrosion resistance of stainless steel

Free consultation.Level, when the embrittlement temperature is improved in the range of -50 ℃ to -100 ℃, it may be used in freezing related projects. Recently, sus430lx (18cr Ti, Nb LC) and sus436l (etc.) have been applied to frozen shells. Ferritic stainless steels are body centered cubic junctions

For example, the raw material difference of 20303, which is common in the market, lies in more than 5000 yuan per ton.

Stainless steel plate has strong moldability, which changes the defect of wood material installation rigidity. As a metal material, it also has better flame retardancy. Mould proof, anti-corrosion, moisture-proof,

Guihu.A new technology called fingerprint free treatment technology can be adopted on the surface of stainless steel plate. This technology mainly uses nano layer technology to form a very thin and strong protective layer on the surface of stainless steel plate, because it can avoid fingerprints left behind by human fingers, which is also called fingerprint free stainless steel plate. nothing

To it is called electrochemical corrosion.

Since the back is not filled with argon, its advantages are obvious, mainly for its simplicity low cost, and suitable for installation on the construction site. However, due to its structural characteristics, flux cored wire has high requirements for welders during operation. Its wire feeding speed is fast and its wire feeding accuracy is high, so it is difficult to master