Hamburg Altona12cr1mov alloy round steelHow to solve the core component problem-World information network

For the production and processing of sculpted copper tubes the sheet metal shall be first opened in the sheet metal workshop according to the dimensions shown in the drawings, which is commonly referred to as opening. Then cut the corners of these open sheets according to the height of the edge, and then use the bending machine to form the edge according to the drawing forming diagram. The shaped copper pipe shall also be installed with reinforcing ribs as required, and the four corners of the shaped plate shall be welded well. The welded parts shall be sent to the grinding workshop, and the spraying surface shall be polished and the welding interface shall be polished and leveled. The polished modeling copper pipe is then sent to the spraying workshop for processing. Before spraying, the surface of the sculpted copper pipe shall be chrome treated and the process hole shall be drilled, so as to ensure that the sculpted copper pipe can be hung on the spraying line well, and the painting can be smooth without flow marks, and the color is consistent without color difference. After that, according to customer demand, the qualified products are pasted with protective film and bound with bubble film or wooden box.

No heating and plating bath is required. The process is simple and easy to operate. The cold drawn degreased copper tube bright tin plating is one of the anti discoloration mirror bright brush tin plating and degreased copper tube tin plating mean copper bar partial or overall tin plating.

Hamburg Altona.On October 16, according to the Economic and Information Commission of Shandong Province, at the end of September 2017, Shandong Province had resolved the overcapacity of 75 million tons of pig iron and 27 million tons of crude steel, and all the de capacity equipment had been shut down and withdrawn. On October 16, the Development and Reform Commission of Handan City released the 2017 Plan for Handan City to Eliminate Excess Iron and Steel Capacity. Statistics show that the iron making capacity of Handan in 2017 was 84 million tons and the steel making capacity was 54 million tons.

.Four in one formula and process conditions Preparation of solution Take formula 1 as an example: mix the calculated amount of water for zinc oxide into a paste, slowly add it into the calculated amount of phosphoric acid under stirring until it is completely dissolved, then add zinc nitrate and tartaric acid, dilute it with water to 2/3 of the total volume, add sodium alkosulfonate and OP emulsion, and stir to make it completely dissolved. Then add chromium dihydrogen phosphate dissolved in dilute phosphoric acid, and add titanium sulfate. After all materials are added, dilute them to the total volume, cool them to room temperature, and soak them for 2-3 days to make them contain enough ferrous ions. When the content of ferrous ion reaches above 7g/L, adjust the free acidity and total acidity of the solution to the specified value, and then the solution can be used at elevated temperature. When the ferrous ion reaches the above value,Hamburg Altona45 # round steel, the phosphating speed is fast, the solution is stable, and the phosphating film is fine and dense. During operation, attention shall be paid to controlling the temperature. If the temperature is higher than 70 ℃, the degreasing technology of degreased copper pipe. How to make degreased copper pipe? The process flow of degreased copper tube? What are the characteristics of degreased copper tubes? Use of degreased copper tube? There are too many questions. Let's solve them at once. Everyone knows the copper tube. Nitrate reacts easily. The heater should be installed on the two walls of the tank, not on the bottom of the tank, to prevent local overheating. Stainless steel pipe or iron pipe should be used for heater, and lead pipe or copper pipe should not be used to avoid contamination of solution by impurities. What is degreased copper pipe? &The advantages of degreased copper pipe's comprehensive treatment of grease, phosphating and passivation are described. This comprehensive treatment process can simplify the process, reduce the work area, save equipment costs, shorten working hours, improve labor productivity and reduce costs. This method can only be used in the occasions where the requirements for coating quality are not high.However, in actual production, due to the amount of oil contamination, light and heavy rust, the consumption rate of each component in the solution is different, so attention should be paid to adjustment and control to maintain its due role. What is the degreasing copper tube? &I have roughly known the degreasing methods of degreasing copper tubes: solvent degreasing, alkali degreasing, high pressure hot water degreasing, electrolytic degreasing, etc. 1 Solvent degreasing: use degreasing solvent to dissolve the oil on the surface of red copper pipe, collect it together into a container, volatilize, collect and reuse the volatile solvent, difficult maintenance which has problems such as low cleaning efficiency, and environmental pollution. In recent years, many kinds of surfactants have been developed.

Some problems. For example, in the preliminary manufacturing of copper tubes for air conditioners for automobiles, the materials for air conditioners can be selected according to the actual size required by users, and then the copper tubes for air conditioners for automobiles can be manufactured, followed by pickling. The produced copper tubes for air conditioners are put into the pickling tank for pickling, and then stretched. Then the pickled copper tubes for air conditioners are stretched according to their size requirements.

Use the medical copper tube table to eat. Because of the unique of the medical copper tube, when the oil drops on the table, it will only stick to the table, but not penetrate the table. Only with a slight wipe of the rag, the oil stains will be easily disappeared. In this case, when cleaning large canteens, the liquidators do not need to spend much effort but are relaxed. They just need to prepare a rag and a basin of clean water, and then carefully scrub it. t2 Medical Copper Tube Company thinks that the medical copper tube table is only made of the surface of the medical copper tube and its exterior is not made of the medical copper tube. The price is cheaper than the wooden table, which is extremely suitable for a small amount of purchase. The medical copper tube has a natural bright and beautiful feeling. The color is extremely blended, these methods can also stop the combined processing and create more medical copper tubes with different appearances. No matter which method is used let's understand some STEPs of the appearance processing of medical copper tubes. There are about five different methods for the appearance processing of medical copper tubes. Connect to t2 Medical Copper Tube Company and introduce them to the master. In addition, the following STEPs should be followed. First, before processing, the agreement should be stopped with the manufacturer, and then a sample should be selected as the standard for future consumption. The second part, when using it, we should guarantee that the coils of the base we choose to use and the coils that are not yet used are the third of the same model and batch. If they are used in some construction, such as elevators, we should pay attention to the unexpected selection of materials. In some places with extraordinary contrast, it is not appropriate to use the mirror t2 medical copper tubes. When processing, it is necessary to select the appropriate manufacturing process, such as weld grinding, how to restore the appearance. Class For the processing of the appearance of some textured t2 medical copper tubes, pay attention to the bias, which is also called unidirectionality. For example, if the lines used are vertical rather than horizontal, it is not easy to apply the dirty residue on the appearance of t2 medical copper tubes. It is extremely easy when they are clean. When finishing, STEP of the process used should be added, so the cost also needs to be added. Therefore, when selecting the appearance of the processing, t2 Medical Copper Tube Company revealed that Panbo consumers should carefully select according to the situation, and when selecting the planning and design staff, they should have a full understanding of the appearance of t2 Medical Copper Tube. Since the birth of medical copper tube, it has been widely used in food, chemical industry, crude oil, machine manufacturing and other industries for its superior . It is precisely because of this kind of universal needs that people are increasingly demanding for medical copper tubes. Although this kind of situation is basically conducive to the development of the medical copper tube industry. Having said so much, the editor of this website will introduce the most popular technology in the medical copper tube industry -- the medical copper tube appearance fingerprint free disposal punishment technology. Mentioned here, I believe that many enemies have learned the greatest advantages of this kind of technology from the name. However, do you know that this is nothing more than a contrast of significant and abstract advantages. The most one-sided introduction is also my face. The medical copper tube after adopting this kind of technical treatment has a smooth appearance and soft hand feeling, and ordinary dust and impurities are not easy to adhere. Therefore, it is also extremely easy to clean. If the ordinary dust is probably dirt, just wipe it with a wet rag and you will lose the clean and smooth appearance. Because the implementation of this kind of craft is to use electroplating oil to shine the film on the red interior line, so it has the characteristics of being tough and not easily scratched. This prevents the possibility that some slight bumps may damage the medical copper tube. It also allows the medical copper tube to be used twice as quickly. Stop the fingerprint free disposal and punish the medical copper tube after the accident. It also loses great promotion in appearance. As the saying goes, a superior appearance can always leave the best impression. Therefore, compared with the medical copper tube after the punishment and the medical copper tube without the punishment, it can often be welcomed by customers and enemies.Hot rolling and hot expansion. The main processing procedures include the blank sawing process, and the production process of the air conditioning copper pipe in the tower mainly includes cold drawing. Ring furnace heating process, piercing process, pipe rolling process, sizing process, cooling bed process, straightening process, pipe cutting soot blowing process, surface inspection, length measurement and weighing to packaging and warehousing. Key points: yield strength limit: when the external force borne by the air conditioning copper tube sample exceeds the elastic limit of the material, although the stress no longer increases, the sample still has obvious plastic deformation. This phenomenon is called yield, that is, when the material bears an external force to a certain extent, its deformation is no longer in direct proportion to the external force, resulting in obvious plastic deformation. The stress when the air conditioning copper pipe yields is called the yield strength limit, and the corresponding S point in the tensile test curve is called the yield point. For air conditioning copper pipes with high plasticity, there will be an obvious yield point on the tensile curve, while for materials with low plasticity, so it is difficult to calculate the yield limit according to the external force at the yield point. Therefore, in the tensile test method, it is usually specified that the stress when the gauge length on the specimen produces 0.2% plastic deformation is taken as the conditional yield limit expressed as 0. The yield limit index can be used as the design basis for requiring that the parts do not produce obvious plastic deformation during operation.

Hamburg Altona12cr1mov alloy round steelHow to solve the core component problem

For the production and processing of sculpted copper tubes, which is commonly referred to as opening. Then cut the corners of these open sheets according to the height of the edge the sheet metal shall be first opened in the sheet metal workshop according to the dimensions shown in the drawings,Hamburg Altona310s stainless steel pipe, and then use the bending machine to form the edge according to the drawing forming diagram. The shaped copper pipe shall also be installed with reinforcing ribs as required, and the four corners of the shaped plate shall be welded well. The welded parts shall be sent to the grinding workshop, and the spraying surface shall be polished and the welding interface shall be polished and leveled. The polished modeling copper pipe is then sent to the spraying workshop for processing. Before spraying, the surface of the sculpted copper pipe shall be chrome treated and the process hole shall be drilled, so as to ensure that the sculpted copper pipe can be hung on the spraying line well, and the painting can be smooth without flow marks, and the color is consistent without color difference. After that, according to customer demand, the qualified products are pasted with protective film and bound with bubble film or wooden box.

The traders have a weak mentality and they are willing to reduce prices and ship goods actively. In addition, the inventory in Chongqing is high and the inventory pressure is high; Shenyang, Northeast China, has little fluctuation. According to the traders' feedback, under the current situation, the traders have reached a potential tacit understanding with the terminal, and try to keep the price stable, and the downstream receiving is weak; North China continued to fall, and the mainstream Tiantie fell to 4450 yuan. Although the deal was completed in the past two weeks, the downstream demand in the peak season did not improve significantly, and the market pull mentality was defeated.

For the production and processing of sculpted copper tubes, the sheet metal shall be first opened in the sheet metal workshop according to the dimensions shown in the drawings, which is commonly referred to as opening. Then cut the corners of these open sheets according to the height of the edge, and then use the bending machine to form the edge according to the drawing forming diagram. The shaped copper pipe shall also be installed with reinforcing ribs as required, and the four corners of the shaped plate shall be welded well. The welded parts shall be sent to the grinding workshop, and the spraying surface shall be polished and the welding interface shall be polished and leveled. The polished modeling copper pipe is then sent to the spraying workshop for processing. Before spraying, the surface of the sculpted copper pipe shall be chrome treated and the process hole shall be drilled, so as to ensure that the sculpted copper pipe can be hung on the spraying line well, and the painting can be smooth without flow marks, and the color is consistent without color difference. After that, according to customer demand, the qualified products are pasted with protective film and bound with bubble film or wooden box.

how much.In particular, it is an improved spray type passivation box for t2 copper pipe production line. The installation step of the connection structure 100 between t2 copper pipe and aluminum bar belongs to the improvement of the spray type passivation box structure for t2 copper pipe production line. The passivation solution spray box is set above the side of the passivation solution box, the passivation solution spray box with downward sloping bottom is connected with the inlet of the passivation solution box by the outlet set on the box wall at the bottom of the inclined bottom, the upper side of the passivation solution box is installed with a passivation pump, and the inlet pipe of the passivation pump is connected with the passivation solution box, The outlet pipe of the passivation pump is connected with the upper port of the passivation liquid spray box. With reasonable structure and convenient operation, it is convenient for operators to add passivation liquid to the passivation box, clean colloidal crystals at the bottom of the passivation box, avoid equipment blockage, avoid crystals adhering to the zinc layer on the surface of galvanized pipe, and improve the surface quality of galvanized steel pipe.

Handle carefully to prevent damage and scratches. 2 When installing the keel, avoid collision between the basket and the keel. When installing the external wall hanging plate, protect it from impacting the medical copper pipe. 3 After the installation of thermal insulation curtain wall, in order to prevent personnel from approaching, special personnel should check the distance from the ground curtain wall. 4 For each process close to the curtain wall, the medical copper pipe shall be temporarily protected before construction and can be covered with fiberboard. Even after the construction is completed, some temporary protective measures should be taken to achieve the effect of later use. 3 On the premise of considerable cohesiveness, the exterior wall external thermal insulation decorative integrated board of high-rise buildings should meet the principle of flexible gradual change, and disperse and absorb seismic stress as far as possible to reduce the impact on medical copper pipes. 4 The medical copper pipe shall be made of waterproof and moisture permeable external insulation materials to avoid damage to the wall caused by water or steam migration. 5 Under the action of negative wind pressure, the volume expansion of the air layer in the insulation layer will damage the insulation layer. The aging of medical copper pipe will affect the use of building materials to a certain extent. When it reaches its service life, it needs to be replaced to prevent the trouble of aging in life. 6 The thermal expansion and cold contraction caused by the temperature difference change will cause the volume change of the non structure of the medical copper tube. Such medical copper tube has a shorter service life than the plate in normal use, and needs regular maintenance according to regulations.

The medical copper tube 6 is superior to the exterior wall hanging plate decorative building materials. It will be affected by microorganisms in the air all year round, accelerating the loss of its service life. 7 If the wall interface is not properly treated, the construction process must be strictly required otherwise it will cause local hollowing of the insulation layer. How to protect the medical copper tube during installation? The medical copper pipe shall be installed in strict accordance with the installation requirements, and the later maintenance work must be done well. 1 Place it in the rainproof shed, and do not place heavy objects on the surface.

Hamburg Altona12cr1mov alloy round steelHow to solve the core component problem

The surface coating of medical copper tube is very important. Observe its thickness, how to prevent the aging of medical copper tube? How to select the foam density of medical copper tube Good medical copper tube and foam density are very high and hard. Check the quality of aluminum zinc coated color steel plate on the surface. As exterior wall thermal insulation decorative plate. Then use your hand to break it up and down to see if it is easy to deform. If you break it with force, it will deform, which is not good. 3 See the price.

Information recommendation.Pay attention to the following points when using flame heating brazing: the selection of welding materials The filler metal is wire or rod, with a diameter of about 35mm. The material is: the melting temperature of wire 221 is about 0905 ℃. Its chemical composition is FB10 The composition is 2331% H3BO3 and 6071% KBF The joint form of brazed copper pipe is mostly plug-in. Before cleaning the brazed copper pipe before welding, the edge of the pipe mouth must be corrected and deburred to ensure that the pipe mouth is free of cracks or other defects. And clean the surface of the inserted part. After the red copper pipe is assembled by tack welding, it shall be fixed by tack welding. The number, size and height of tack welds shall be symmetrically and evenly distributed along the circumference from top to bottom, left to right, and the tack welds shall be melted into the whole weld during brazing. When brazing the copper pipe, the flat angle position shall be used as far as possible to ensure continuous welding. Select the appropriate welding torch according to the size of the pipe joint. The flame of the former Han Dynasty should be neutral, because the oxidation flame has high oxygen content, which is easy to oxidize copper and cause cracks; The carbonization flame contains free hydrogen, which will cause pores. When heating pipes before welding, the flame shall be perpendicular to the heating surface, the pipe joints shall be heated evenly, and the base metal shall be heated as quickly as possible to avoid excessive temperature and heating time of the through pipe joints. During the brazing of degreased copper tube, the brazing seam and filler metal shall be under the protection of flame. In addition, it shall be noted that the brazing seam shall be naturally cooled after welding, and the weldment shall not be moved before the brazing seam has solidified. After natural cooling after welding, hot water or wet cloth shall be used to wipe the brazing seam and remove welding slag to improve corrosion resistance and reliability of post welding inspection.

Strong connection firmness of copper pipe: the connection between copper pipe and copper fittings is strong.

Now let me talk about the damages that are easy to occur on the surface of the copper tube. In order to prevent the accumulation of process agents or products and/or dirt, scratches and other rough surfaces, mechanical cleaning must be carried out. If the copper pipe is heated to a certain high temperature in the air during welding or grinding, chromium oxide heat return color will appear on both sides, lower surface and bottom of the weld. The color after tempering is thinner than that of the oxidation protective film, and is clearly visible. The color depends on the thickness. The thicker oxide can be found in the rainbow color, blue purple to brown. It is usually black. It is caused by being at high temperature or being at high temperature for a long time. When any of these oxide layers exist, and the corrosion resistance of these areas will. In this case the chromium content on the metal surface will, it is not only necessary to heat temper the color and other oxide layers, but also to clean the chromium poor metal layer under it. Free iron on the surface of t2 copper tube will rust, causing corrosion of stainless steel. Therefore, there are many surface iron sources, including cleaning with ordinary carbon steel wire brush and shot peening with sand glass beads or other abrasives previously used on ordinary carbon steel, low alloy steel or cast iron, or regrinding non stainless steel products attached to copper pipe components and equipment. If there is no protection during cutting or hoisting, slings and iron on the working surface can easily be embedded or dirty the surface. The copper tube shall be boiled in boiling water for 30 seconds before cold treatment. The effective internal stress is about 15%, and the residual austenite reaches the effect. Then, the cold treatment can be carried out as usual. Of course, the second suggestion is to choose the normal treatment at minus 60 degrees, and then conduct deep cooling at minus 120 degrees. The lower the treatment temperature is, the retained austenite will be rapidly transformed into martensite, but it cannot be transformed. Through experiments, it can be found that there will be about 2% of retained austenite. At this time, retained retained austenite can achieve a certain buffer effect. After cold treatment, the air conditioning copper pipes need to be taken out and put into hot water for heating, which can effectively heat about 40% of the cold treatment stress. Tempering and cold treatment should be carried out as soon as possible after gradual heating, and most of them can avoid cracks as soon as possible, so as to ensure that the products will not deform in later use and facilitate daily storage. The transformation characteristics of the area of each layer of the copper tube during empty drawing affect the asymmetry of the deformation of the metal material. One of its characteristics is that the natural widening of each layer along the wall thickness is not consistent. Of course, the external layer of the copper tube is less, the internal surface layer of the copper tube is larger, and the natural widening of the middle layers is slow from the external layer to the internal surface layer.The technical level of degreasing copper tube for mechanical equipment With the substantial improvement of the manufacturing level of mechanical equipment and the degree of control automation in China, there is still some gap between the technical level of domestic degreasing copper tube production line and the products of foreign counterparts. After years of reform and opening up. The quality of all aspects of degreased copper pipe has also risen by several grades, significantly narrowing the quality gap with the imported production line. The aluminum hose production line and aluminum can production line developed and produced by the company break the technological monopoly of foreign companies, can provide stable and reliable production equipment for domestic and international markets, and make great contributions to the aluminum packaging industry. With the continuous improvement of people's living standards, there will be more and more demand for degreased copper tube products, and its market potential is huge. Problems such as incomplete penetration, cracks and air holes are easy to occur during the fusion welding of degreased copper tubes. Compared with fusion welding, wood is not melted during brazing, which reduces the impact of large thermal conductivity of base metal on welding quality, prevents the formation of incomplete penetration, reduces the tendency to produce pores and cracks, and ensures the performance of weld. Because the base metal is not melted, when the oil drops on the table, it will only stick to the table, when cleaning large canteens the oil stains will be easily disappeared. In this case, the liquidators do not need to spend much effort but are relaxed. They just need to prepare a rag and a basin of clean water and then carefully scrub it. t2 Medical Copper Tube Company thinks that the medical copper tube table is only made of the surface of the medical copper tube, and its exterior is not made of the medical copper tube. The price is cheaper than the wooden table, which is extremely suitable for a small amount of purchase. The medical copper tube has a natural bright and beautiful feeling. The color is extremely blended, and can stop the very good embellishment and reaction with the color in the surrounding situations. Now, let's understand some STEPs of the appearance processing of medical copper tubes. There are about five different methods for the appearance processing of medical copper tubes. Connect to t2 Medical Copper Tube Company and introduce them to the master. In addition, these methods can also stop the combined processing and create more medical copper tubes with different appearances. No matter which method is used, the following STEPs should be followed. First, before processing the agreement should be stopped with the manufacturer, and then a sample should be selected as the standard for future consumption. The second part, when using it, we should guarantee that the coils of the base we choose to use and the coils that are not yet used are the third of the same model and batch. If they are used in some construction, such as elevators, we should pay attention to the unexpected selection of materials. In some places with extraordinary contrast, it is not appropriate to use the mirror t2 medical copper tubes. When processing, it is necessary to select the appropriate manufacturing process, such as weld grinding, how to restore the appearance. Class For the processing of the appearance of some textured t2 medical copper tubes, pay attention to the bias, which is also called unidirectionality. For example if the lines used are vertical rather than horizontal, it is not easy to apply the dirty residue on the appearance of t2 medical copper tubes. It is extremely easy when they are clean. When finishing, STEP of the process used should be added, so the cost also needs to be added. Therefore, when selecting the appearance of the processing, t2 Medical Copper Tube Company revealed that Panbo consumers should carefully select according to the situation, and when selecting the planning and design staff, they should have a full understanding of the appearance of t2 Medical Copper Tube. Since the birth of medical copper tube, it has been widely used in food, chemical industry, crude oil, machine manufacturing and other industries for its superior . It is precisely because of this kind of universal needs that people are increasingly demanding for medical copper tubes. Although this kind of situation is basically conducive to the development of the medical copper tube industry. Having said so much, the editor of this website will introduce the most popular technology in the medical copper tube industry -- the medical copper tube appearance fingerprint free disposal punishment technology. Mentioned here, I believe that many enemies have learned the greatest advantages of this kind of technology from the name. However, do you know that this is nothing more than a contrast of significant and abstract advantages. The most one-sided introduction is also my face. The medical copper tube after adopting this kind of technical treatment has a smooth appearance and soft hand feeling, and ordinary dust and impurities are not easy to adhere. Therefore, it is also extremely easy to clean. If the ordinary dust is probably dirt, just wipe it with a wet rag and you will lose the clean and smooth appearance. Because the implementation of this kind of craft is to use electroplating oil to shine the film on the red interior line, so it has the characteristics of being tough and not easily scratched. This prevents the possibility that some slight bumps may damage the medical copper tube. It also allows the medical copper tube to be used twice as quickly. Stop the fingerprint free disposal and punish the medical copper tube after the accident. It also loses great promotion in appearance. As the saying goes, a superior appearance can always leave the best impression. Therefore, compared with the medical copper tube after the punishment and the medical copper tube without the punishment, and the production process of the air conditioning copper pipe in the tower mainly includes cold drawing. Ring furnace heating process, piercing process, pipe rolling process, sizing process, cooling bed process, straightening process, pipe cutting soot blowing process, magnetic flux leakage detection process, surface inspection, length measurement and weighing to packaging and warehousing. Key points: yield strength limit: when the external force borne by the air conditioning copper tube sample exceeds the elastic limit of the material, although the stress no longer increases, the sample still has obvious plastic deformation. This phenomenon is called yield, that is, when the material bears an external force to a certain extent, its deformation is no longer in direct proportion to the external force, resulting in obvious plastic deformation. The stress when the air conditioning copper pipe yields is called the yield strength limit, and the corresponding S point in the tensile test curve is called the yield point. For air conditioning copper pipes with high plasticity, while for materials with low plasticity, there will be no obvious yield point so it is difficult to calculate the yield limit according to the external force at the yield point. Therefore, in the tensile test method, it is usually specified that the stress when the gauge length on the specimen produces 0.2% plastic deformation is taken as the conditional yield limit, in particular to a connecting structure of a copper tube and an aluminum row. At present, most of the copper aluminum transition joints have not been effectively protected. In this way, under the condition of long-time electrification and heating and affected by the water vapor or corrosive gas in the air, the parts at the connection point are more likely to be oxidized, resulting in the reduction of the effective contact area of the connection point, the increase of the contact resistance, and the excessive heating or even burning of the connection point.

The material cost of medical copper tube will not be less than 40 yuan. The better the material is, the higher the price will be. It is called &one cent, one cent&. Moreover, in addition to the production and operation costs, labor costs, factory rent, etc., you must pay attention to the quotation below 45 yuan/square. Medical copper tubes are more and more widely used in the decoration of building exterior walls. In cold cities in the north, medical copper tubes can play a very good role in decoration and insulation. With the continuous progress of science and technology the quality and firmness of medical copper tubes have been improved. However, as long as the decoration materials are used, they will inevitably crack during installation and construction. As time goes by, there will be aging to varying degrees in daily life. Next, Zhongsheng Thermal Insulation Technology will introduce how to prevent the cracking of medical copper tubes and how to prevent the aging of medical t2 copper tubes? Let's talk about these two issues. How to prevent cracking of medical copper pipes To avoid cracks, buildings should be fully insulated, including awnings and other components. Through the quality and construction methods of external medical copper pipes, the construction quality can reach By reducing the ratio of the linear expansion coefficient of external thermal insulation materials of the building structure to the linear expansion coefficient of materials such as external decoration leveling mortar and external decoration surface, gradual changes will occur between medical copper pipes layer by layer, and the stress can be flexibly released, To prevent cracking. How to prevent medical copper tube from aging? The insulation layer of high-rise buildings shall have fire resistance , and shall have the characteristics of preventing fire spread and releasing smoke or toxic gas in case of fire. The strength and volume of materials shall not be reduced too much, and the surface shall not burst or collapse. Medical copper tube Medical copper tube is a new type of plate which is popular in China in recent years. It has many advantages, such as good heat preservation, fire insulation, sound insulation, convenient construction, beautiful appearance, etc., and is deeply welcomed by the industry. The medical copper pipe may fall during use. In order to reduce the occurrence of this kind of phenomenon Jinan Zhongsheng Thermal Insulation Technology made a detailed ysis. Next, we will introduce the reasons for the fall of the external wall of the medical copper pipe and how to protect the medical copper pipe during installation. Reasons for the fall of the external wall of the medical copper pipe The medical copper pipe was not firmly fixed and moved, forming a push-pull effect, causing local hollowing of the insulation layer,Hamburg Altona15CRMO alloy plate, and long-term water seepage after cracks leading to the fall of the insulation layer. 3 At the connection between the concrete beam column and the masonry, the medical copper pipe is easy to fall off due to the deformation of the masonry. 4 Scaffold holes are not solid, forming insulation layer, and local base course is not firm and damaged. 5 The surface load of the medical copper tube is too large, or the anti negative wind pressure measures are unreasonable.