Torres vedras321 stainless steel round steelSpecial application environment

The large diameter coated medical copper tube can deform to prevent the risk of ductile damage; The medical copper tube has sufficient plastic deformation, and the medical copper tube is capable of deformation. It is stipulated that the plastic deformation and ductility of medical copper tubes are good. Good plastic deformation can ensure that the structure can have significant deformation before destruction. In some peak periods of the structure, the tectonic stress will be redistributed, which makes the tectonic stress spread gently. Good ductility indicates that under dynamic and static loads, more kinetic energy should be digested and absorbed when the structure is destroyed, the size of the deformation working capacity of medical copper tubes has a particularly critical practical significance. 3 Production and processing characteristics of medical copper tubes. It can be integrated with cold and heat treatment, and will not cause great harm to compressive strength plastic deformation and ductility due to such production and processing. 4 Weldability of medical copper tube. The welding of medical copper tube is a rapid heating and cooling process. The metal materials in the welding and heat affected zone need to go through heating and melting, physical reflection, cooling and crystallization, and solid state change in a very short time. The industry trend is a kind of medical copper tube. Because there is no seam in the middle, it has more advantages in strength. Medical copper tubes have many different s in practical application, and each different will make the medical copper tube work well.Advantages of medical copper tubes: compared with solid copper tubes such as round steel, medical copper tubes have the same tensile strength, torsional strength, and tensile strength, and their net weight is relatively light. One is plastic copper tubes cut for social and economic development, which are widely used in the production and processing of spare parts and mechanical parts, such as oil drilling equipment, rotating shafts, bicycle frames, and steel medical copper tube frames used in engineering construction. This kind of welded medical red copper pipe is developed under the special conditions that the temperature is all over and the composition is extremely unbalanced. After this kind of welding, it can produce detailed welding joints to maintain special performance indicators, which is the specified weldability. 5 Performance of medical copper tube. It refers to the service life of medical copper tube. The production and processing of annular parts with medical copper tubes can achieve the utilization rate of raw materials, simplify the production process, save raw materials and manufacturing hours, etc. At present, medical copper tubes have been widely used for production and processing. Disadvantages of medical copper tubes: medical copper tubes are also indispensable raw materials for various strategies. Drums must be produced and processed by medical copper tubes. Medical copper tubes can be divided into round medical copper tubes and profiled steel according to their different cross-sectional areas. Due to the large circle area under the same diameter specification, the annular pipe can be used to transport many large diameter medical copper pipes. Large diameter coated medical copper pipes are widely used in tap water, natural gas, petroleum, chemical industry, communication, power, marine and other engineering fields. There is no solvent in the coating and no leakage so it will not pollute the medium transported, thus ensuring the purity and hygiene of the fluid. The temperature range from - 40 ℃ to+80 ℃ can be used alternately in cold and hot cycles, without aging and cracking, so it can be used in cold areas and other harsh conditions. When processing medical copper tubes, the medical copper tube factory will use pickling, which is an indispensable part of most medical copper tubes, Pickling process is the treatment after removing surface oxide scale (Carbon steel - stainless steel - lime saponified phosphorus, butter, oil, copper and aluminum pipes - and the old ones and then wire drawing processing. Then what are the points to be noted when washing? 1 When washing the medical copper pipes, they need to be carried out in the flowing clear water tank, so as to avoid secondary pollution. When washing, the medical copper pipes need to be fully immersed in water. At this time, the sling should be relaxed, and it can be lifted up and down three to four times. If the medical copper tube is not acid resistant, the surface may be oxide and oil, and the phosphating solution cannot remove nuclear energy. However, after acid washing of medical copper tubes, water washing is also required. 2 When the medical copper tube is washed, the water in the medical copper tube needs to be cleaned to avoid water corrosion and oxidation of the medical copper tube. Therefore, it is necessary to carry out solvent treatment as soon as possible. 4 When the medical copper tube is washed the iron salt content must be controlled within a certain range, otherwise the medical copper tube may be damaged.

Copper tube can be strengthened by heat treatment, the strength increases, but the plasticity drops sharply. Therefore, seawater, seawater carbonic acid and most organic acids are higher than those of copper tube. Copper tubes can be made.

Torres vedras. When the copper tube is heated and the flux melts into liquid, place the preheated electrode on the welding point immediately. As soon as the electrode begins to melt, move the flame nozzle back and forth until the solder flows into the gap between the two tubes Remove the flame let the solder contact the welding point, and then remove it after a few seconds. If it is suspected or found that there is still a gap between the two pipes. It can be heated again to make the flame nozzle move continuously at two points. A small amount of solder can be added.

Four in one formula and process conditions Preparation of solution Take formula 1 as an example: mix the calculated amount of water for zinc oxide into a paste, slowly add it into the calculated amount of phosphoric acid under stirring until it is completely dissolved then add zinc nitrate and tartaric acid, dilute it with water to 2/3 of the total volume, add sodium alkosulfonate and OP emulsion, and stir to make it completely dissolved. Then add chromium dihydrogen phosphate dissolved in dilute phosphoric acid, and add titanium sulfate. After all materials are added, dilute them to the total volume, stir them to make the solution even, cool them to room temperature, put a large amount of iron filings in the solution, and soak them for 2-3 days to make them contain enough ferrous ions. When the content of ferrous ion reaches above 7g/L, adjust the free acidity and total acidity of the solution to the specified value, and then the solution can be used at elevated temperature. When the ferrous ion reaches the above value, the phosphating speed is fast, the solution is stable, and the phosphating film is fine and dense. During operation, attention shall be paid to controlling the temperature. If the temperature is higher than 70 ℃, the degreasing technology of degreased copper pipe. How to make degreased copper pipe? The process flow of degreased copper tube? What are the characteristics of degreased copper tubes? Use of degreased copper tube? There are too many questions. Let's solve them at once. Everyone knows the copper tube. Nitrate reacts easily. The heater should be installed on the two walls of the tank, not on the bottom of the tank, to prevent local overheating. Stainless steel pipe or iron pipe should be used for heater, and lead pipe or copper pipe should not be used to avoid contamination of solution by impurities. What is degreased copper pipe? &The advantages of degreased copper pipe's comprehensive treatment of grease, rust removal, phosphating and passivation are described. This comprehensive treatment process can simplify the process, reduce the work area, save equipment costs, improve labor productivity and reduce costs. This method can only be used in the occasions where the requirements for coating quality are not high.However, in actual production, due to the amount of oil contamination, light and heavy rust, the consumption rate of each component in the solution is different, so attention should be paid to adjustment and control to maintain its due role. What is the degreasing copper tube? &I have roughly known the degreasing methods of degreasing copper tubes: solvent degreasing, alkali degreasing, ultrasonic degreasing, high pressure hot water degreasing, electrolytic degreasing, etc. 1 Solvent degreasing: use degreasing solvent to dissolve the oil on the surface of red copper pipe, collect it together into a container, volatilize, collect and reuse the volatile solvent, and separate the pollutants from the circulation system. This method was used in the early stage, which has problems such as low cleaning efficiency, difficult maintenance,Torres vedras12Cr1MoV alloy steel plate, and environmental pollution. In recent years, many kinds of surfactants have been developed.

.The demand for t2 copper tubes is increasing. At the same time, in the market, the quality identification method of t2 copper tube for grid fittings is currently accompanied by rapid economic development. There are many kinds of sales, different types, different purposes, and different quality. Therefore, when purchasing, you should be clear and have certain selection skills. Here we introduce the quality identification method of t2 copper tube. The color of t2 copper tube depends on the color of t2 copper tube. Although the external color is a visible factor, the color of the product is closely related to its production process and quality control. If the product is bright in color and high in glossiness, it is generally superior to the product with poor color. The t2 copper tube with uniform thickness should be selected. Because some small manufacturers are limited in technology and process, it is difficult to ensure that the product thickness is uniform and neat. Therefore, the thickness is also an important factor to test the quality of the pattern plate. Later, the casting process of t2 copper tube.

The utility model relates to a connecting structure, in particular to a connecting structure of a copper tube and an aluminum row. At present, most of the copper aluminum transition joints have not been effectively protected. In this way, under the condition of long-time electrification and heating and affected by the water vapor or corrosive gas in the air the parts at the connection point are more likely to be oxidized, resulting in the reduction of the effective contact area of the connection point, the increase of the contact resistance, and the excessive heating or even burning of the connection point.

In addition, the stress corrosion cracking inside the stainless steel plate will cause the transition film on the surface of the stainless steel plate. Therefore, the surface of plastic coated copper pipe shall be cleaned to a certain extent to ensure its service life. The oil cracking tube circuit breaker must be selected. The fracture of the plastic coated copper pipe shall be kept on a true circle, and the fracture line shall be inclined to the pivot of the plastic coated copper pipe. Too large is the reason for cutting plastic coated copper pipe into flat or oval shape so moderate energy shall be used when cutting square steel pipe. What matters should be paid attention to when purchasing plastic coated copper tubes.

However, for some important parts, it is also considered that the yield ratio should be smaller to improve their safety and reliability. However at this time, the utilization rate of materials is also low. Common sense: copper pipes for air conditioners are mainly used for conveying liquid, gas and steam; Boiler pipes and steam transmission pipes are used for the piping, structure and steam transmission of steam boilers, including the transmission of high-temperature and high-pressure steam; Structural pipe, widely used in aviation, automobile, tractor and other industrial sectors; Pipe for petroleum industry, mainly used for oil and gas exploitation, such as casing, drill pipe and tubing and pipe for petroleum refining and processing; Pipe for mechanical manufacturing, which is used to manufacture the race of ball bearing, rotating shaft and body of air pump and hydraulic pump; High pressure vessel, used for manufacturing bottles, boilers, shells, etc. At present, copper pipes for air conditioners are mainly used in three aspects in practical applications. First, high-rise civil buildings, oil platforms, bridges, railway vehicles and other fields. Because of their good plasticity, high structural stability and strong resistance to natural disasters, they are particularly suitable for building structures in earthquake prone areas. Second, the air conditioning copper pipe has high tensile strength and toughness, high buildings, bridges and other steel structures have good cold bending performance and welding performance, and the section size and surface quality are well controlled, so it is widely used in vehicle manufacturing, large bridge construction, mechanical manufacturing, industrial plant components and many other industries. Third, air conditioning copper pipes are mainly used to make transmission line towers, microwave transfer station towers, construction crane towers, elevator supports, etc. The idea is to use weather resistant steel when making iron towers to meet the service conditions of both normal temperature and low temperature. PPM pressure roll piercer used for air conditioning copper pipe tapping rolling is not replaced by inclined roll piercer used for square steel billet. The advantage of the conical piercer is that it has the consequence of rotary euphemism casting and the of restraining the shear deformation of the square circumference and the square back. Therefore, it can prevent the defects outside the steel pipe. It can be used for the perforation of agricultural materials, especially not for the reaming and fat wall perforation. When using a general piercer, while when using a square cone piercer, the T/D limit can be 2%. Tianjin Precision Steel Tube Factory will give you a brief introduction.

Brass tube Soft copper tube is called hose, and the tube is used to replace the hard one, so soft copper is widely used. Besides being in a straight line, cut according to the free length so as to avoid leakage of copper tube brass welding. Soft copper tube requires local bending of air conditioner, and mechanical oil tube.

The editor of this website of t2 Medical Copper Tube Company said that if there is no table refrigerator they can only stand to eat and probably enjoy food in other places. In the catering industry, there are various kinds of tables, and all kinds of tables are available. There are wooden tables and medical copper controlled tables. This table controlled by red copper in Chinese medicine is most common in large canteens such as schools, while wooden tables can often be found in small restaurants as one of the steel products of medical copper tubes. As his name is common, medical copper tubes have the ability to prevent rust. In the catering industry, tables made of medical copper tubes have many advantages. Next, the teacher of Medical Copper Tube Consumption Co., Ltd. will introduce you to the master. The medical copper tube table is easy to see in the large canteen. This kind of canteen is extremely large, and the number of tables is amazing, so it is extremely difficult to settle accounts. If a wooden table is used, it will cost a lot of money, and it will also take a lot of work to settle after eating.

discount.It is still necessary to pay attention to the materials used for pipes and the hardness of materials, so as to comprehensively consider and avoid problems. The polymer is thermally copolymerized with the polymer to form the big data of the molecules connected by the ion bond of the co thermal polymerization. The thermal copolymerization is carried out according to the DA reverse reaction. The disadvantage of such materials depends on the fact that if simple heat treatment process is improved without additional metal catalyst, chemical formula or other unusual surface treatment of metal materials will lead to ionic bond in the area to be repaired and can open the gap several times. Copper tube concrete based textile materials. Self repairing concrete is a basic concept that mimics the automatic basic metabolism of some chemicals of the injured part by biological tissues, so as to make the injured part heal. Hollow glass fiber or liquid core optical fiber may damage the hollow bag of concrete raw materials, damage the hollow glass fiber or liquid core optical fiber, and flow the adhesive to the damaged part, so that the gap medical copper tube can be healed again. Cause of surface damage of copper tube. Copper tube is also a kind of material commonly used in engineering. The surface shall also be protected from scratches. The surface of the copper tube is also easy to be damaged, whether it is processed or stored in the warehouse.

Now let me talk about the damages that are easy to occur on the surface of the copper tube. In order to prevent the accumulation of process agents or products and/or dirt, scratches and other rough surfaces, mechanical cleaning must be carried out. If the copper pipe is heated to a certain high temperature in the air during welding or grinding, chromium oxide heat return color will appear on both sides, lower surface and bottom of the weld. The color after tempering is thinner than that of the oxidation protective film and is clearly visible. The color depends on the thickness. The thicker oxide can be found in the rainbow color, blue, purple to brown. It is usually black. It is caused by being at high temperature or being at high temperature for a long time. When any of these oxide layers exist, the chromium content on the metal surface will, and the corrosion resistance of these areas will. In this case, it is not only necessary to heat temper the color and other oxide layers, but also to clean the chromium poor metal layer under it. Free iron on the surface of t2 copper tube will rust, causing corrosion of stainless steel. Therefore, the powder that must float can usually be removed together with the dust. Some are very sticky and must be treated as embedded iron. In addition to dust, there are many surface iron sources, including cleaning with ordinary carbon steel wire brush and shot peening with sand, glass beads or other abrasives previously used on ordinary carbon steel,Torres vedras2205 stainless steel plate, low alloy steel or cast iron, or regrinding non stainless steel products attached to copper pipe components and equipment. If there is no protection during cutting or hoisting, the wire ropes, slings and iron on the working surface can easily be embedded or dirty the surface. The copper tube shall be boiled in boiling water for 30 seconds before cold treatment. The effective internal stress is about 15%, and the residual austenite reaches the effect. Then, the cold treatment can be carried out as usual. Of course, the second suggestion is to choose the normal treatment at minus 60 degrees, and then conduct deep cooling at minus 120 degrees. The lower the treatment temperature is, the retained austenite will be rapidly transformed into martensite, but it cannot be transformed. Through experiments, it can be found that there will be about 2% of retained austenite. At this time, retained retained austenite can achieve a certain buffer effect. After cold treatment, the air conditioning copper pipes need to be taken out and put into hot water for heating, which can effectively heat about 40% of the cold treatment stress. Tempering and cold treatment should be carried out as soon as possible after gradual heating, and most of them can avoid cracks as soon as possible, so as to ensure that the products will not deform in later use and facilitate daily storage. The transformation characteristics of the area of each layer of the copper tube during empty drawing affect the asymmetry of the deformation of the metal material. One of its characteristics is that the natural widening of each layer along the wall thickness is not consistent. Of course, the external layer of the copper tube is less, the internal surface layer of the copper tube is larger, and the natural widening of the middle layers is slow from the external layer to the internal surface layer.The technical level of degreasing copper tube for mechanical equipment With the substantial improvement of the manufacturing level of mechanical equipment and the degree of control automation in China, there is still some gap between the technical level of domestic degreasing copper tube production line and the products of foreign counterparts. After years of reform and opening up. The quality of all aspects of degreased copper pipe has also risen by several grades, significantly narrowing the quality gap with the imported production line. The aluminum hose production line and aluminum can production line developed and produced by the company break the technological monopoly of foreign companies, can provide stable and reliable production equipment for domestic and international markets, and make great contributions to the aluminum packaging industry. With the continuous improvement of people's living standards, there will be more and more demand for degreased copper tube products, deformation, cracks and air holes are easy to occur during the fusion welding of degreased copper tubes. Compared with fusion welding wood is not melted during brazing, which reduces the impact of large thermal conductivity of base metal on welding quality, prevents the formation of incomplete penetration, reduces the tendency to produce pores and cracks, and ensures the performance of weld. Because the base metal is not melted, the structure and properties of the base metal are almost unchanged, so that the original service properties of the base metal can be maintained.

Copper tube has good bearing capacity. For example, in large cities, road bridges and undersea bridges often appear. Most road bridges are built with plastic coated copper pipes. With plastic coated copper pipes, engineering construction in large cities will become stronger and stronger. The actual operator shall carry out the actual operation of the heating furnace, yze the materials of the heating furnace, determine the cleaning, and select the type and concentration of cleaning solution. Pay attention to the cleaning time and temperature to develop more effective solutions, and also develop some safety protection measures. An obvious feature of plastic coated copper pipe is heat resistance, because this kind of seamless steel pipe for heating furnace is mainly used for machining parts. Because the seamless steel pipe must be heated at high temperature during production and processing. What are the plastic coated copper tubes to prevent wear. What are the plastic coated copper tubes to prevent wear. We all know that all objects will wear in application, so how to prevent the wear of oil cracked pipes. Now let's introduce it to you. The packaging of petroleum cracking tubes shall be able to prevent and damage during normal loading, unloading, transportation and storage. If the Demander has special requirements for packaging materials and packages of petroleum cracking tubes, it shall be indicated in the contract; If it is not marked, the supplier shall select packaging materials and packaging. Packaging materials shall comply with relevant requirements. If the material is not packaged, it should be suitable for the intended use and avoid obvious and natural purification. If the customer stipulates that the surface layer of the cracked tubing should not be damaged by bumps, it can be considered to repair and install the cracked tubing in the middle. Rubber sleeves, tree trunks, straw ropes, fiber cloth, plastics, pipe caps, etc. can be used for maintenance and installation. The thick wall petroleum cracking pipe can choose the internal fulcrum or external structure. Because thick walled tubes are thin. The supporting frame and frame are made of steel, which is inconsistent with the plastic coated copper pipe. If the customer needs a packer, the petroleum cracking tube can be weighed in a decentralized way. However, the specification must be 159MM500MM.

The material cost of medical copper tube will not be less than 40 yuan. The better the material is, the higher the price will be. It is called &one cent, one cent&. Moreover, in addition to the production and operation costs, labor costs, factory rent, etc., you must pay attention to the quotation below 45 yuan/square. Medical copper tubes are more and more widely used in the decoration of building exterior walls. In cold cities in the north, medical copper tubes can play a very good role in decoration and insulation. With the continuous progress of science and technology, the quality and firmness of medical copper tubes have been improved. However, as long as the decoration materials are used, there will be aging to varying degrees in daily life. Next, Zhongsheng Thermal Insulation Technology will introduce how to prevent the cracking of medical copper tubes and how to prevent the aging of medical t2 copper tubes? Let's talk about these two issues. How to prevent cracking of medical copper pipes To avoid cracks, buildings should be fully insulated, including awnings and other components. Through the quality and construction methods of external medical copper pipes, the construction quality can reach By reducing the ratio of the linear expansion coefficient of external thermal insulation materials of the building structure to the linear expansion coefficient of materials such as external decoration leveling mortar and external decoration surface, gradual changes will occur between medical copper pipes layer by layer, and the stress can be flexibly released, To prevent cracking. How to prevent medical copper tube from aging? The insulation layer of high-rise buildings shall have fire resistance , and shall have the characteristics of preventing fire spread and releasing smoke or toxic gas in case of fire. The strength and volume of materials shall not be reduced too much, and the surface shall not burst or collapse. Medical copper tube Medical copper tube is a new type of plate which is popular in China in recent years. It has many advantages, such as good heat preservation, fire insulation, sound insulation, convenient construction, beautiful appearance, etc., Jinan Zhongsheng Thermal Insulation Technology made a detailed ysis. Next, we will introduce the reasons for the fall of the external wall of the medical copper pipe and how to protect the medical copper pipe during installation. Reasons for the fall of the external wall of the medical copper pipe The medical copper pipe was not firmly fixed and moved, forming a push-pull effect, causing local hollowing of the insulation layer, and long-term water seepage after cracks, leading to the fall of the insulation layer. 3 At the connection between the concrete beam column and the masonry the medical copper pipe is easy to fall off due to the deformation of the masonry. 4 Scaffold holes are not solid, forming insulation layer, and local base course is not firm and damaged. 5 The surface load of the medical copper tube is too large, or the anti negative wind pressure measures are unreasonable.

Good quality.However, for some important parts it is also considered that the yield ratio should be smaller to improve their safety and reliability. However, at this time, the utilization rate of materials is also low. Common sense: copper pipes for air conditioners are mainly used for conveying liquid, gas and steam; Boiler pipes and steam transmission pipes are used for the piping, structure and steam transmission of steam boilers, including the transmission of high-temperature and high-pressure steam; Structural pipe, widely used in aviation, automobile, tractor and other industrial sectors; Pipe for petroleum industry, mainly used for oil and gas exploitation, such as casing drill pipe and tubing, and pipe for petroleum refining and processing; Pipe for mechanical manufacturing, which is used to manufacture the race of ball bearing, the plunger, rotating shaft and body of air pump and hydraulic pump; High pressure vessel, used for manufacturing bottles, boilers, shells,Torres vedras6082 aluminum bar, etc. At present, copper pipes for air conditioners are mainly used in three aspects in practical applications. First, medical copper pipes are widely used in industrial plants, municipal engineering, bridges, railway vehicles and other fields. Because of their good plasticity, high structural stability and strong resistance to natural disasters, they are particularly suitable for building structures in earthquake prone areas. Second, the air conditioning copper pipe has high tensile strength and toughness, high buildings, bridges and other steel structures have good cold bending performance and welding performance, and the section size and surface quality are well controlled, large bridge construction, mechanical manufacturing, industrial plant components and many other industries. Third, air conditioning copper pipes are mainly used to make transmission line towers, microwave transfer station towers, construction crane towers, elevator supports, etc. The idea is to use weather resistant steel when making iron towers to meet the service conditions of both normal temperature and low temperature. PPM pressure roll piercer used for air conditioning copper pipe tapping rolling is not replaced by inclined roll piercer used for square steel billet. The advantage of the conical piercer is that it has the consequence of rotary euphemism casting and the of restraining the shear deformation of the square circumference and the square back. Therefore, it can prevent the defects outside the steel pipe. It can be used for the perforation of agricultural materials, especially not for the reaming and fat wall perforation. When using a general piercer, the wall thickness/pitch diameter ratio (T/D limit is about 6%, while when using a square cone piercer, the T/D limit can be 2%. Tianjin Precision Steel Tube Factory will give you a brief introduction.

The difference between hard copper tubes and soft copper tubes in use Hard copper tubes can only be used as straight tubes and cannot be bent. Therefore, they are generally used in power plants, switches of electrical equipment, and places where the connection points are far away and do not need to be bent. Compared with soft copper tubes, the price of hard copper tubes will be lower. Although the name of the soft copper tube is soft tube, so the soft copper tube is used in more places, and can be used in a straight tube way, as well as in a coiled tube way. The length of the copper tube can be longer if the coil is used. If the connection point is longer, it can be cut randomly according to the length, we need not consider the preservation problem unless we buy a small amount at home. For example, large manufacturers use copper units to buy a large number of copper pipes once, so there will be a problem. I believe some people do not know how to store unused copper materials, Now let's ask our staff to introduce the storage method of copper for you.

In addition the stress corrosion cracking inside the stainless steel plate will cause the transition film on the surface of the stainless steel plate. Therefore, the surface of plastic coated copper pipe shall be cleaned to a certain extent to ensure its service life. The oil cracking tube circuit breaker must be selected. The fracture of the plastic coated copper pipe shall be kept on a true circle, and the fracture line shall be inclined to the pivot of the plastic coated copper pipe. Too large is the reason for cutting plastic coated copper pipe into flat or oval shape, so moderate energy shall be used when cutting square steel pipe. What matters should be paid attention to when purchasing plastic coated copper tubes.

Torres vedras.The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material, and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, machinery manufacturing steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering electric power engineering, power plants, agricultural and chemical machinery, glass curtain walls, boiler construction, highway railings, housing construction, pressure vessels, oil tanks, bridges, power station equipment, lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall, the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing, weldability and corrosion resistance.

The utility model relates to a connecting structure, in particular to a connecting structure of a copper tube and an aluminum row. At present, most of the copper aluminum transition joints have not been effectively protected. In this way, under the condition of long-time electrification and heating and affected by the water vapor or corrosive gas in the air, the parts at the connection point are more likely to be oxidized, resulting in the reduction of the effective contact area of the connection point, the increase of the contact resistance, and the excessive heating or even burning of the connection point.

Plastic coated copper pipe is one of the safe carbon fiber products. Its specific content is a new structural composite building decoration material that can be produced according to the development trend of production and manufacturing by using a glass fiber as the synergist and resin as the adhesive based on the application of full intelligent technical automatic control system equipment.