Washington DCH
Washington DCEalso known as lifting stages
Application and characteristics of stage elevators: Stage elevators, are specifically installed on the stage and used for lifting and rotating the stage. They are called stage elevators. It has multiple functions such as lifting, rotating, and tilting, and adopts protective measures such as self-locking, interlocking, travel switch, mechanical limit, hydraulic explosion-proof, etc.
Small typesetting Copyright Shu ICP Bei No. 11019783-1
Washington DC.To understand the operation of the mechanism, the main focus is on whether it is normal and whether there is noise during use. When faults are found, timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation, it is necessary to disassemble or adjust the rotating mechanism. In this case it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.
Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
.We
When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.
Regardless of the type of lifting platform used, people are more concerned about the stability during use. Because the stability not only affects the actual use effect, but also has varying degrees of impact on the safety during use, it is necessary to pay appropriate attention. The same applies when using fixed loading and unloading platforms, but many times the stability of this type of platform can be trusted. The reason for saying this is because the manufacturer has taken this issue into account during production and manufacturing, and the following aspects are taken to avoid this situation.
Regularly check the connection of each part, and tighten it if there is any looseness
When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, there may be short lines or damaged components. Using a table for inspection is relatively better.
Drain all the hydraulic oil in the oil tank,Washington DCManned hydraulic lifting platform, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
how.Secondly, for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, and after changing the hydraulic oil it must be automatically lifted and lowered 2 to 3 times to ensure that the air in the oil cylinder is completely discharged, maintain sufficient space, and ensure that the lifting platform can be lifted to the rated lifting height.
Shafts must have split pins and be sufficient.
The purpose of the stage elevator: The telescopic stage adopts an effective guidance system, which reduces the gap between the telescopic stage and the fixed stage during the translation process, ensures smooth operation, and continuously changes speed. The synchronous device adopts a low speed and large torque drive,Washington DCSimple hydraulic lifting platform, making the stage parallel, free, and retractable in place during the stretching process, and can automatically achieve leveling. Suitable for cultural and entertainment venues such as halls, cinemas, multifunctional halls, studios cultural sports venues, hotels, etc.
When the motor overheats, it should be stopped immediately, and after troubleshooting, it should continue to operate. The motor bearings should be in good condition.
Inspection standard.When the motor overheats, it should be stopped immediately, and after troubleshooting, it should continue to operate. The motor bearings should be in good condition.
When a hydraulic lifting platform malfunctions, it is necessary to take time to prepare accordingly. At this time, it is necessary to provide timely feedback or communicate with the manufacturer. If a voltage range is used to detect the hydraulic lifting platform, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
Update Log
Washington DC.Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, but does not have a price advantage. Therefore, a power source is used as the lifting power source, it must be cleaned with gasoline or rare materials.