VicenzaIndoor 
VicenzaHydraulVicenza10 meter lifting hydraulic platform,
Materials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.
Volume speed control circuit: Speed control is achieved by adjusting the displacement of a variable pump or variable motor.
Vicenza.Firstly, rust prevention is necessary. Because the part of the hydraulic cylinder needs to extend out of the cylinder during operation, it will naturally be corroded by oxides and acidic gases. This requires us to apply an appropriate amount of grease to protect it from erosion as a weight component. If we change the oil, we must open the box and use it for a long time to prevent the hydraulic cylinder from being used for a long time. In the operation of hydraulic cylinders, the speed should be appropriate and should not exceed 2m/s to extend the service life of the hydraulic cylinder. In addition, in order to protect the mechanism and safety, it is very important to install buffer devices internally to protect the hydraulic cylinder. The greater the pressure of the protective hydraulic cylinder, the heavier the load, and the greater its pressure. A specialized product manufacturing enterprise that integrates research and development, as well as service. A long-term professional elevator manufacturer
Aluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work, and can only provide support for 1-2 people.
.Lines of various safety equipment
When the hydraulic oil of the equipment is insufficient, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.
After 10000 hours of operation on the hydraulic lift, major repairs will be carried out to the mechanical and electrical systems.
The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.
The manufacturer of hydraulic cargo elevators tells you the reason for the instability of hydraulic lifting equipment. Hangzhou hydraulic cargo elevator equipment has always had good stability, mainly used for heavy types of goods. However, during use Hangzhou hydraulic cargo elevators may inevitably encounter some faults during the lifting process, such as very unstable conditions. What is the reason for the instability of the elevator? How to solve these problems?
When placing materials on the platform, they should be placed in the middle of the platform as much as possible. The weight of the goods should be within the standard load range of the equipment, and the volume of the goods should not exceed the platform size of the equipment. Otherwise materials and lifting platforms may be injured and dangerous accidents may occur. High priced and various specifications of elevator manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!
Job description.The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.
The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface,VicenzaPrice of hydraulic platform lift truck, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.
Lifting mechanism: The workbench should be ensured to rise and fall smoothly, and there should be no jumping lifting phenomenon. All moving parts should be flexible when moving, and there should be no jamming devices. The lifting system of the elevator is divided into electric or manual hydraulic systems, pipelines, and joints.
Test conclusion.Reason: The lowering speed valve is out of adjustment. Cleaning method: If the lowering speed valve is adjusted, and if the adjustment is ineffective, please contact the manufacturer in a timely manner to avoid exceeding the warranty period.
When the hydraulic system malfunctions, the hydraulic elevator may experience problems with the hydraulic pump, motor, valve, and hydraulic installation after repairing the hydraulic system, which can easily cause vibration and generate significant noise.
Vicenza.The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.
After the pre installation is completed, the pre installed equipment should be fixed, and the positions of cables, oil pipes and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws, and the hydraulic cargo elevator after reinforcement has robustness and safety.
Stability: The workbench should evenly withstand 125% of the MAX load capacity and be stable at the MAX elevation.