BazhouHydrauli
BazhouHydrauliAn inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage,BazhouIndoor hydraulic lifting platform car, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, dust or rust is poor, and the device will produce; Buzz&# quo; Noise.
Regularly check whether each organization is functioning properly and whether there is noise. If problems are found,BazhouMobile hydraulic lifting platform, they should be promptly cleaned up.
Bazhou.When working on scaffolding without scaffolding or without railings, if the height exceeds 5 meters, safety belts must be used or other reliable safety measures must be taken.
The lifting platform is a multifunctional heavy loading and unloading mechanical equipment which can be divided into fixed and mobile, guide rail and curved arm types. Fixed types include scissor elevators, chain elevators, loading and unloading platforms, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, to avoid any worries about after-sales service.
The undercut length of the weld mm should not exceed 10% of the weld seam, and the depth should not exceed 0.4mm.
The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.
When using hydraulic elevators, frequent inspections and maintenance should be carried out, which not only extends the service life of the hydraulic elevator, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).
High altitude work should always use tool bags. Tools with larger boarding bridges should be tied to sturdy components with ropes, and should not be placed randomly to prevent accidents caused by falling from a height.
There is noise inside the hydraulic cylinder. When replacing the hydraulic oil, there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible, even when arranging pipelines, it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.
Safety production.New reference wiring diagram 2. Elevator leg noise. Mobile elevators should open the legs before operation. In this case, if the legs lack butter noise will be generated.
There are many reasons for unstable workbench descent, such as overload unstable support,BazhouFixed hydraulic elevator, severe eccentric load, hydraulic oil impurities, etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.
The installation personnel should confirm and count the equipment details, confirm that there are no omissions in the shipped equipment details, check if the tools are complete, and ensure the smooth progress of the installation process.
After 1500 hours of elevator operation, perform minor repairs to the mechanical and electrical systems.
Promise and keep promise.The installation personnel should confirm and count the equipment details, confirm that there are no omissions in the shipped equipment details, check if the tools are complete, and ensure the smooth progress of the installation process.
When repairing the hydraulic system, only clean plastic plugs can be used to seal the end of the pipeline.
The contact of the travel switch must be firmly opened and closed, and the contact crater should be polished in a timely manner.
Bazhou.Hydraulic cargo elevators have been used in some high-altitude operations in recent years, and now some hydraulic cargo elevators are gradually mentioned as large machinery such as tower cranes, becoming a better choice for some high-altitude operations. However, which have certain constraints.
When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.
The undercut length of the weld mm should not exceed 10% of the weld seam, and the depth should not exceed 0.4mm.