LecceHydraulic
LecceCylinder When using, the weight should be evenly distributed, mainly in the center of the countertop. However, for special cases, partial loading is allowed, but the longitudinal load cannot exceed half of the rated load. The horizontal load should not exceed one-third of the rated load, so this detail needs to be noted during use.
Especially when its pipes are in use, they are quite boring and can roll, so in this case, they need to be blocked or tied tightly. This is relatively appropriate, so it is necessary to pay attention to these details during use. Especially for unmanned protective lifting platforms, it is not allowed to carry people during use, and it is strictly prohibited to carry people. If the electric lifting platform truck carries people during use, the lifting platform is equipped with railings or anti crack valves, which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.
Lecce.The lifting platform truck should be placed in a trench position and corresponding anti slip measures should be taken; Remove the gearbox of the equipment, remove the axle oil box, and take out the lower bearing and oil suction device; Slowly test drive and check if the surface around the axle diameter is severely damaged; If the damage is severe and tungsten is occupied, it should be polished smooth with an oilstone; Under the electric motor, place the sleeper on the trench edge on the inner side of the steel rail,Lecce20 meter hydraulic lift, use a jack to regularly pull the electric motor and remove the upper tile; How to solve the damage of important equipment in the lifting platform car? Check the status of the bearing pads and oil absorbers, investigate the cause of the damage,LecceScissor fork hydraulic lifting platform, replace the bearing pads, and clean the bearing oil box; After assembling all components, install a new oil suction device on the axle oil box and clean the axle oil; Gear oil of gear box shall be as specified; Burning of axle box bearings is a common occurrence, which is the burning of outer bearings. In severe cases, it can cause the axle box and wheel set to be fixed together, affecting equipment operation.
In the past in large workshops, if goods had to be transferred from one place to another, it would be very expensive. For loading, unloading, and transferring 2 tons of goods, it would require 10 people to work continuously for several hours, using forklifts to operate and multiple forklifts to work simultaneously for one or two hours. Moreover, using forklifts also required professional forklift drivers, and the cost of using them was often high. Is there any way to do this, Can it meet both rapid loading and unloading of goods and low-cost needs? Of course there is, that is the application of fixed loading and unloading platform trucks. A fixed loading and unloading platform truck is an auxiliary equipment that mainly completes the rapid loading and unloading of goods. It has an adjustment function, a fixed loading and unloading platform truck can adjust the height and serve as a bridge to connect the truck and warehouse, meeting a large number of cargo handling needs, But such a large workload requires only one operator to operate, greatly saving labor costs and manpower, improving the production efficiency of the enterprise. Professional hydraulic lift truck manufacturer with high prices, service on-site settlement, and honest operation!
.The characteristics of hydraulic lifting platform vehicles are very obvious, such as their overall weight being relatively light, and their maneuverability being relatively good, so they are relatively suitable. The mast columns of its system are equipped with guide wheels, so its lifting and lowering are relatively stable during use. Of course, it is also important to pay attention to the structure of the hydraulic lifting platform truck and ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.
To understand the operation of the mechanism, the main focus is on whether it is normal and whether there is noise during use. When faults are found, timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation it is necessary to disassemble or adjust the rotating mechanism. In this case, it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.
For lifting platform vehicles without manned protection, it is strictly prohibited to carry people during use. At the same time, attention should be paid during use to prevent damage to hands, feet, and clothing.
The safety of fixed loading and unloading platform vehicles is high. The platform vehicle device is made of steel plate and has many protrusions on it, which increases the friction force of the goods. The sliding of the goods due to low friction force is placed to complete the damage of the goods. This design can effectively prevent slipping, and the entire design is safe and easy to operate.
The lifting platform truck should be placed in a trench position and corresponding anti slip measures should be taken; Remove the gearbox of the equipment, and take out the lower bearing and oil suction device; Slowly test drive and check if the surface around the axle diameter is severely damaged; If the damage is severe and tungsten is occupied, investigate the cause of the damage, replace the bearing pads, and clean the bearing oil box; After assembling all components, install a new oil suction device on the axle oil box and clean the axle oil; Gear oil of gear box shall be as specified; Burning of axle box bearings is a common occurrence, which is the burning of outer bearings. In severe cases, it can cause the axle box and wheel set to be fixed together, affecting equipment operation.
The safety of fixed loading and unloading platform vehicles is high. The platform vehicle device is made of steel plate and has many protrusions on it, which increases the friction force of the goods. The sliding of the goods due to low friction force is placed to complete the damage of the goods. This design can effectively prevent slipping, and the entire design is safe and easy to operate.
Free consultation.The above detailed introduction, I believe everyone has a comprehensive understanding and understanding of the use of hydraulic elevators, and these details cannot be ignored during the use process.
The above detailed introduction, I believe everyone has a comprehensive understanding and understanding of the use of hydraulic elevators, and these details cannot be ignored during the use process.
The characteristics of hydraulic lifting platform vehicles are very obvious, such as their overall weight being relatively light, and their maneuverability being relatively good, allowing even a single person to operate, so its lifting and lowering are relatively stable during use. Of course it is also important to pay attention to the structure of the hydraulic lifting platform truck and ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.
The characteristics of hydraulic lifting platform vehicles are very obvious such as their overall weight being relatively light, and their maneuverability being relatively good, allowing even a single person to operate, so they are relatively suitable. The mast columns of its system are equipped with guide wheels, so its lifting and lowering are relatively stable during use. Of course, it is also important to pay attention to the structure of the hydraulic lifting platform truck and ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, some small and narrow channels are also possible, so we need to pay attention to this point.
Meticulous workmanship.When using a hydraulic lifting platform truck, there are many details that cannot be ignored. It mainly uses an external power supply, so when operating, the staff needs to master its operating knowledge, which is the basic content. At the same time, it is also necessary to master corresponding emergency response plans. When processing, it is also necessary to check the corresponding route, which is the basic content. So in addition, what preparations do hydraulic elevators need to master during use?
Failure lack of hydraulic oil, and oil leakage in the oil cylinder are all key issues for inspection. They must be cleaned once a week to prevent dust and debris from affecting normal operation.
The characteristics of hydraulic lifting platform vehicles are very obvious, such as their overall weight being relatively light, and their maneuverability being relatively good, allowing even a single person to operate, so they are relatively suitable. The mast columns of its system are equipped with guide wheels, so its lifting and lowering are relatively stable during use. Of course, it is also important to pay attention to the structure of the hydraulic lifting platform truck and ensure its compact structure, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.
Lecce.The quality of elevators on the market varies and many people have no way to choose when making purchases. If there is time,LecceStraight top hydraulic lifting platform, on-site inspections can be conducted to understand the size of production, such as the production process, which can be learned through on-site inspections. It is good to choose manufacturers with strong capabilities, as these manufacturers have good product quality and after-sales service. These products have a longer usage cycle, indicating that there are many details that cannot be ignored during the purchasing process. Our company has been engaged in various types of hydraulic lift truck price manufacturers and other materials for years, and operates with integrity. Welcome to call!
Of course, the hydraulic lifting platform truck uses a dual protection structure, which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform truck will be safer during operation. The process of operating the hydraulic lifting platform truck should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
The function of a fixed loading and unloading platform truck. The fixed loading and unloading platform truck meets the loading and unloading needs of goods, and has good load-bearing effect, convenient loading and unloading, low consumption, and easy operation. The stability of the loading and unloading process is strong, and the height can be adjusted and lifted to a suitable position to meet the loading and unloading of goods. The later maintenance is in place and the maintenance cost is low.