Garman LakeHyd
Garman LakeLarAfter careful inspection, it was found that it was mainly caused by two reasons
Installing bearings for elevators may seem simple, but it is also important to pay attention to some details, such as: it is actually difficult to thrust bearings into the shaft pins when excessively installing them. However, sometimes, some people may think of using a hammer to hammer the bearings for convenience, and use brute force during installation. In fact, directly hitting the bearings with a hammer can cause significant damage to the bearings, which is the main reason for bearing damage and reducing the service life of the bearings. So when installing bearings, we must not go too far. Fortunately, we can place some soft cloth or cardboard on top of them before installing them.
Garman Lake.Readjust the overflow valve when the pressure is low. Adjust the oil level to be too low at 100% rated load, fill the hydraulic oil with suction oil, filter the blockage, and clean the oil suction section of the filter for air leakage. Check the oil suction pipe and joints; Tighten the joint. Replace the connector if necessary.
Each box, distribution box, etc. is usually kept clean, and dust on electrical equipment should be quickly swept away.
.When using the distribution box, the electric leakage switch meets the requirements for construction elevators. If the fixed elevator installed is variable frequency, the selection of the leakage switch should be compatible with the frequency converter.
The surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than 50%. Specializing in product and renewable resource business, including: scissor lift manufacturers
High altitude work is now also very common, and elevators are also highly demanded by the market. Many high-rise transportation tasks are completed by elevators with high efficiency and reassuring safety. However, attention should also be paid to the installation of the elevator, otherwise there may be problems,Garman LakeHydraulic lifting platform fixed hydraulic, and no one wants to see such a situation happen. What are the installation precautions for elevators?
Drain and discard the hydraulic oil from the hydraulic lifting cargo elevator. For the outdoor guide rail elevator, tighten the joint and remove the oil filter. After cleaning, clean it with compressed air, and then return it to the oil tank and connect the pipeline.
A sign of slowing down has occurred. After the speed slows down, consider the hydraulic oil flow rate first. The factors that affect hydraulic oil flow include: hydraulic pipelines, hydraulic valves, hydraulic oil pumps, motor speed control assembly, etc. The following editor will introduce to you the four reasons for the slower speed and the mediation methods.
Check the rollers, intermediate shafts,Garman LakeIndoor hydraulic lifting platform car, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
device management.Mobile elevators are generally used in skyscrapers where electric elevators are used, as there is no need to stop midway, so fast elevators are needed. First go to the high-rise sky lobby (high-rise elevator lobby, Skylobby) from the ground, and then transfer to the ordinary elevator to the destination. Some new elevators use elevator pre calling systems, which can pre call designated floors in the lobby. These passenger elevators can be decorated beautifully according to customer needs. Some passenger elevators are also equipped with air conditioning and television, while others are set up in the cabin, so that customers can enjoy the scenery outside while riding.
Guide rail type cargo elevators are a type of equipment for transporting heavy objects up and down, and have great applications in factories, workshops and other places. For this type of heavy machinery, its daily maintenance and upkeep are very important, because some small details can have a significant impact on the operation safety of the equipment if not paid attention to. Therefore, maintaining, and cleaning the elevator, be sure to support the support rod.
Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than 50%
ranking.Guide rail type cargo elevators are a type of equipment for transporting heavy objects up and down, and have great applications in factories, and other places. For this type of heavy machinery its daily maintenance and upkeep are very important, because some small details can have a significant impact on the operation safety of the equipment if not paid attention to. Therefore, attention should be paid to the daily maintenance of cargo elevators.
Secondly, there should be no dirt on the friction surface. If there is any dirt, it needs to be washed off with gasoline or thinner; The reduction gearbox, gearbox, external meshing gear, and other parts of the equipment, must be tested according to the requirements in the table; The correct maintenance method for hydraulic guide rail elevators is to regularly check the steel wire ropes in various parts for any breakage or looseness. If this phenomenon is found, it should be replaced in a timely manner. The maintenance of the steel wire ropes must be strictly carried out in accordance with the specifications; Check the connection status of each part according to the braking regulations. If there is any looseness, it should be tightened in a timely manner. The tightness of the connecting bolts of the equipment should be checked when the body is under pressure. All connecting shafts should be equipped with split pins; According to regulations, check the normal operation of each mechanism, whether there is noise or malfunction, and adjusting the rotating mechanism of the equipment disassembling, it is important to ensure that the centerline of the reducer and gear is parallel, and the meshing clearance is appropriate; Regularly conduct a comprehensive inspection of the equipment to check if there is any damage to the wires and cables, and if there is any overheating of the motor. Replace and eliminate the fault in a timely manner before continuing operation; Ensure the bearings of the motor, each box, distribution box, and electrical
Check the rollers, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
Garman Lake.Check the rollers, intermediate shafts,Garman LakeHydraulic lifting platform manufacturer, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
The application scenarios of mobile elevators may require several or even dozens of passenger elevators in some office buildings and hospitals. In order to increase the speed, efficiency, and usable area of electric elevators, most high-rise buildings will divide electric elevators into arrays, with each group responsible for a portion of the floors, and make different adjustments and scheduling based on the usage mode of different floors at different times.
Remove and disassemble the hydraulic lift cargo elevator lowering valve, blow out the plunger with compressed air, then install it and reinstall it.