CasoriaAluminuAdvantages: Due to the wide selection of electronic control switches, the aluminum alloy elevator with remote operation system can be operated remotely even on harsh construction sites, improving the comfort of operation and convenient walking. On the basis of traditional aluminum alloy elevators, steel bar transportation devices and concrete transportation devices are installed, which can transport steel bars, concrete, and workers, greatly improving construction efficiency; The optional advanced stepless frequency control system enables the elevator to achieve stepless speed regulation of 0-60m/min.
It is strictly prohibited to run the engine for a long time in a closed garage. The exhaust gas of the aluminum alloy elevator engine contains carbon monoxide. This is a toxic gas that has been in low concentration for a long time
Casoria.Single set high-strength aluminum alloy mast elevator, with light weight and good maneuverability, it can be divided into: single mast aluminum alloy lifting platform: supported by single mast operating platform, which is an early aluminum alloy elevator. The entire machine is light in weight and flexible in movement, suitable for single person operation. After condensation, it can enter general standard doorways and elevators in buildings.
.With the continuous development of society, for the increasingly widespread use of the internet, many things can be solved on the internet. For mobile elevators, their prices also vary greatly. Due to various factors, their prices vary. So what are the reasons for the large price difference for aluminum alloy elevators? Below, I will take you to understand the reasons for the large price difference of aluminum alloy elevators.
Aluminum alloy elevators are a product of modern high-altitude operations. During their development, the performance and quality of aluminum alloy elevators have continuously strengthened, how much do you know about their scientific design solutions?
. Before the maintenance of the hydraulic aluminum alloy elevator starts, the tools used must be counted. After the maintenance is completed, the tools should be classified and organized, and counted to prevent the tools used for maintenance from being left inside the equipment, especially in the distribution box. When repairing the hydraulic system of the aluminum alloy elevator, it is necessary to keep the maintenance site clean and dust-free. When repairing and fastening screws for aluminum alloy elevators, it is necessary to use the correct diagonal first. When tightening screws, use a torque wrench to prevent excessive damage to the screws. After the maintenance is completed and before the power on test, it is necessary to count the number of maintenance personnel to ensure that there is no one inside the aluminum alloy elevator. This is very necessary for the maintenance of large fixed hydraulic elevators. After counting the number of people, inspecting and repairing the equipment and the maintenance site, the power transmission test can only be carried out. After the maintenance of the aluminum alloy elevator is completed, the equipment maintenance record must be filled out. The maintenance record should include the equipment maintenance date, the personnel participating in the maintenance the maintenance items, the brand, model and specification of the replaced parts, the effectiveness of the maintenance, and whether the equipment still has problems after the maintenance is completed.
Hydraulic lifting platform products are divided into curved arm hydraulic aluminum alloy elevators, scissor fork hydraulic aluminum alloy elevators, mast hydraulic aluminum alloy elevators, and straight arm hydraulic aluminum alloy elevators according to their working modes. Hydraulic aluminum alloy elevator is a replacement product of folding arm aluminum alloy elevator (lifting platform) and scissor fork aluminum alloy elevator (lifting platform). It can be widely used for the decoration and decoration of stations, airports, hotels, posts and telecommunications, municipal gardens, grain depots, cleaning companies, public building facades, or the installation and maintenance of power systems. This aluminum alloy elevator has the advantages of light weight self-propelled walking, electric starting, self supporting legs, simple operation, large working area,CasoriaAluminum alloy self-propelled elevator, and especially the ability to cross obstacles for high-altitude operations.
Compact structure, able to enter the car of general elevators, as well as smooth door openings and narrow passages.
Multi mast aluminum alloy lifting platform: the whole platform is refined by high-strength aluminum profiles. Due to the high strength of the profiles, the four mast structure is adopted, which has excellent stability, flexible operation, large load capacity, large platform area and convenient implementation. Its appearance allows for high lifting capacity in extremely small spaces. Minimize the deflection of the lifting platform.
Where can I find it?.According to the number of masts, it can be divided into: single mast aluminum alloy lifting platform: supported by single mast operating platform, which is an early aluminum alloy elevator. The entire machine is light in weight and flexible in movement, suitable for single person operation. After condensation, it can enter general standard doorways and elevators in buildings.
Method for hydraulic oil leakage in aluminum alloy elevator: Check if the pipe joints are loose and try to tighten them. Check if the viscosity of the hydraulic oil used is too low. When checking the leakage point of the hydraulic oil system generally, the place where hydraulic oil seeps out is the leakage point, but it is not ruled out that the leaked hydraulic oil may accumulate along the pipeline deviating from the leakage point. Therefore, it is important to carefully search during inspection. High priced aluminum alloy elevator manufacturers of various specifications welcome scrap merchants, industrial companies, and power departments to visit and negotiate with the company!
Aluminum alloy elevator is a multifunctional high-altitude work equipment that uses electric hydraulic transmission. It has the advantages of light weight, self walking, electric starting, self supporting legs, simple operation, large working surface, it requires overall maintenance. Below is an introduction to the maintenance precautions for the mobile aluminum alloy elevator.
Double masted aluminum alloy lifting platform: a new generation product of the design, made entirely of high-strength aluminum profiles. Due to the high strength of the profiles the deflection of the lifting platform is minimal. Adopting a double mast column structure, it has a large load capacity, a large platform area, excellent stability, and convenient implementation. Its appearance allows for high lifting capacity in extremely small spaces. This elevator is widely used for three masted aluminum alloy lifting platforms: three sets of masts support the operation platform for synchronous lifting, and the support structure is the same as a single masted platform, with super large load capacity and work stability. The overall lifting guardrail device has good strength and greatly reduces the height of the entire machine during transportation. It is very convenient for loading and unloading, and can be assembled or disassembled in one lift. The elevator has a strong load-bearing capacity and is suitable for two people (who can carry a certain amount of weight tools and materials) to climb high at the same time; Various non-standard products can also be customized according to different environments to meet different needs.
average method.Firstly, the maintenance process should be carried out on the premise of ensuring the safety of staff. Before repairing the aluminum alloy elevator, the power must be disconnected and the power must be verified and hung up; No power transmission, people working&# quo; Identification plate for. During the maintenance process, it is not allowed to disconnect the grounding wire of the aluminum alloy elevator. If it is necessary for maintenance work, after the maintenance is completed,CasoriaHydraulic aluminum alloy elevator, the grounding wire must be connected before the power test can be conducted. When replacing spare parts for aluminum alloy elevators, it is necessary to ensure that the spare parts are intact and of the same model. Items such as valves and seals should be placed in dry and dust-free packaging. When hydraulic aluminum alloy elevator maintenance requires entering the platform for internal work, after the aluminum alloy elevator is lifted, the working surface of the aluminum alloy elevator must be fixed or supported firmly with a crane or other equipment,
The double masted aluminum alloy elevator is made of high-strength and high-quality aluminum alloy material, which has the advantages of beautiful appearance, small size, light weight, balanced lifting, safety and reliability. It is widely used in factories, hotels, restaurants stations, airports, theaters, exhibition halls, and other places. It is a good safety partner for maintenance equipment, painting decoration, changing lighting fixtures, electrical appliances, cleaning and maintenance, and other purposes.
The cost of aluminum alloy elevators also depends on the cost of the product. Products with different material specifications have different functions, lifespan, and safety performance. When it comes to aluminum alloy elevators many people only focus on price, neglecting safety and durability.
Casoria.Each box,Casoria9-meter aluminum alloy elevator, distribution box, etc. should be kept clean regularly and dust on electrical equipment should be promptly cleaned.
Strictly follow the operating instructions of the aluminum alloy elevator for safe use, and strictly prohibit illegal operations.
Method: Check the length or diameter of the power supply lead. When the wire length is not more than 25 meters, the wire diameter should not be less than 1m ²; When the wire length is not greater than 50 meters, the wire diameter should not be less than 5m ². You can try fixing the plug directly to the socket without moving the cable.