Xinfu8-meter h
XinfuMast type
XinfuHydraulicThe optional configurations of a fixed lifting platform include manual hydraulic power, movable flip plates that are easy to overlap with surrounding facilities, rolling or motorized roller tracks, organ type safety protective covers manual or motorized rotating workbenches, hydraulic overturning workbenches,XinfuHydraulic electric lifting platform, safety support rods to prevent the lifting platform from falling, stainless steel safety nets, electric or hydraulic lifting platform walking power systems, and universal ball countertops.
After 1500 hours of elevator operation, perform minor repairs to the mechanical and electrical systems.
Xinfu.Hydraulic elevators and load-bearing oil cylinders can directly act on the foundation pit requiring low shaft strength, and brick or brick concrete structure shafts.
Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.
.Remember not to overload, overload is the root cause of many faults.
The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.
Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.
When using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level 5, please stop using it; When the lifting height exceeds 10 meters, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platform
In addition, the lifting mechanism also needs to be equipped with powerful support frames. Therefore, the selection of lifting mechanism or lifting mechanism for hydraulic freight elevators cannot be generalized, frequent inspections and maintenance should be carried out, which not only extends the service life of the hydraulic elevator, but also enables it to exert greater power during operation. Of course hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).
Application process.Introduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it,XinfuSmall hydraulic lifting platform, forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, improve the efficiency of loading and unloading operations, speed up the flow of materials, and obtain greater economic benefits.
The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.
The hydraulic oil used in the system has the same brand, and the oil temperature is between 45~80 ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.
The speed circuit is the circuit that switches the motion speed and speed of the actuator in the hydraulic system of the guide rail hydraulic lifting platform. Mainly including valves, pumps, and actuators. The commonly used speed circuits include speed circuits, high-speed circuits, and speed switching circuits.
Application process.The smoothness of the gearbox, gearbox, external meshing gears, and hydraulic oil are all carried out according to the requirements in the smoothness table.
Hydraulic cargo elevators are mainly used for the transportation of high-altitude goods such as factory assembly lines, cargo warehouses, docks, buildings, logistics, etc. This product can achieve multi-point, interactive interlocking between upper and lower floors, achieving safe use and carrying capacity of 30 tons. The above are the fields in which hydraulic cargo elevators are applied and the characteristics of hydraulic cargo elevators that we want to share with everyone.
Reason: Manual pump and gear pump have severe oil leakage. Cleaning method: Replace the oil pump sealing ring to clean it. Reason: Gear pump is damaged, The oil pumped out has no pressure. Cleaning method: Replace the gear pump to clean the problem. Reason: Lack of hydraulic oil. Cleaning method: Add enough hydraulic oil to clean the problem. Reason: Circuit open. Cleaning method: Check the button and fuse to clean the problem. Reason: Filter blockage. Cleaning method: Replace or clean the problem. Reason: Support valve or electromagnetic directional valve malfunction. There are two situations: the input voltage of the electromagnetic coil is lack of 220V. The solenoid coil is burnt out and the valve core is stuck. Cleaning method: maintenance or replacement can be used to clean the natural descent of the lifting platform. Reason and cleaning method: one-way valve leakage cleaning method: check the check valve in the valve. Assuming there is dirt on the sealing surface of the check valve. Clean the check valve.
Xinfu.Voltage too low: Measure the starter voltage,XinfuFixed electric hydraulic lifting platform, with an allowable fluctuation range of± 10%.
There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.
I believe many people want to know about the maintenance issues of guide rail hydraulic lifting platforms, as it is related to their service life. During use, frequently check the connection of each part. If loose, tighten it. When the body is under pressure, the tightness of the connecting bolts of the body should be checked (the pressure state that can be used). All connecting shafts should have split pins and hydraulic cargo elevators should be fully opened.