BusiaFixed hyd
BusiaCustomizeWhat are the maintenance rules for the mechanical equipment of hydraulic elevators? The brakes of each mechanism should be regularly inspected and adjusted to ensure flexibility and reliability. On the friction surface, there should be no dirt present, and any dirt must be washed off with gasoline or thinner.
After entering winter, elevators are prone to some small problems and malfunctions, which requires users to perform seasonal maintenance and upkeep on the elevator. Below, the editor will briefly introduce the winter maintenance precautions and key points of the elevator.
Busia.What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and elevator are intact, and strictly check whether the dimensions of each part connected to the motor and elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.
Mobile elevators are generally used in skyscrapers where electric elevators are used, as there is no need to stop midway, so fast elevators are needed. First go to the high-rise sky lobby (high-rise elevator lobby, Skylobby) from the ground, and then transfer to the ordinary elevator to the destination. Some new elevators use elevator pre calling systems, which can pre call designated floors in the lobby. These passenger elevators can be decorated beautifully according to customer needs. Some passenger elevators are also equipped with air conditioning and television,BusiaDouble shear hydraulic lifting platform, while others are set up in the cabin, so that customers can enjoy the scenery outside while riding.
.Regularly check all wires and cables for damage. Timely bandage and replace damaged parts. Various scissor lift manufacturers have formal qualifications. Welcome to inquire by phone and sincerely invite cooperation!
What are the advantages of installing a guide rail type elevator for goods? The advantages of civil engineering are easy to install: there is no need for a machine room above the shaft, and the top layer can be installed at a height of more than 5 meters. The computer room can be located within a radius of 15 meters of the shaft, occupying an area of only 3-4 square meters. The hydraulic elevator is not equipped with a counterweight device to improve the utilization rate of the shaft area. The load and load cylinder of the hydraulic elevator directly act on the foundation pit, and the strength requirement for the shaft is low. A brick structure or brick concrete structure shaft is sufficient.
Talking about the daily maintenance and use of hydraulic lifting platform motors. Overloading is strictly prohibited, as overloading can increase the burden on the motor and in severe cases, cause the motor to burn out.
Every month, it should be ensured to add butter twice to the transmission position where the grease nipple is located. For areas where butter cannot be added, it is necessary to clear the oil circuit or replace the grease nipple until butter can be added. Otherwise, it is prohibited to use the equipment.
A type of elevator equipment consisting of a walking mechanism hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump and enters the lower end of the hydraulic cylinder through the oil filter, isolation electromagnetic directional valve, throttle valve, hydraulic control one-way valve, and balance valve causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the isolation electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.
Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
how much.Avoid, especially during storage. Store in a cool and dry place, and avoid rainy and snowy weather during work.
Hydraulic oil should be kept clean and replaced every 6 months; When repairing, maintaining, and cleaning the elevator, be sure to support the support rod.
The pressure of the lifting platform is very important. When lifting goods, the general lifting platform will prompt, which serves as protection. Therefore, now lifting platforms are equipped with pressure gauges. Hydraulic machinery should remind everyone to pay attention to the following points: the precautions for using small lifting platforms are based on pressure. Their load-bearing capacity is very poor and their size is small. When using the lifting platform, it is necessary to pay attention to its use. If overloaded, it will cause structural damage to the lifting platform. We have mentioned this many times before when using it.
The seat belt needs to be inspected every six months, with a load of 225 kilograms. The test time is five minutes. After the test, check whether the seat belt is broken or deformed, and keep records of the experiment. Any unqualified seat belts should be immediately stopped from use.
The cost is reasonable.Avoid, especially during storage. Store in a cool and dry place,BusiaElectric hydraulic lifting platform, and avoid rainy and snowy weather during work.
Hydraulic lifting platforms can be divided into: four wheel mobile, two wheel traction, car modification, car type, auxiliary self-propelled, so what precautions should we pay attention to during the break-in period when using a hydraulic lifting platform? Today, the editor will share this topic with everyone.
Busia.The product has a sturdy structure, smooth lifting, simple and convenient installation and maintenance,BusiaMicro hydraulic lifting platform, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will tell you about the level
The correct construction inspection of the airport is to first inspect the foundation to see if there is any water accumulation and to see if the grounding system meets the requirements. We also need to see how the structural bolts of this frame are tightened, and whether there are any cracks in the welds. We need to set them according to the instructions. In mechanical transmission, it can be divided into two types: open type and closed type. Of course there are also many safety equipment for elevators.
The pressure of the lifting platform is very important. When lifting goods, the pressure of the lifting platform will test the weight of the goods. If it is overloaded, the general lifting platform will prompt, which serves as protection. Therefore, now lifting platforms are equipped with pressure gauges. Hydraulic machinery should remind everyone to pay attention to the following points: the precautions for using small lifting platforms are based on pressure. Their load-bearing capacity is very poor and their size is small. When using the lifting platform, it is necessary to pay attention to its use. If overloaded, it will cause structural damage to the lifting platform. We have mentioned this many times before when using it.