Hamburg Ames bOutdoor elevators and factory cargo elevators are heavy lifting mechanical equipment. Outdoor elevators are used for transporting goods between floors of buildings, and operation buttons can be set on each floor and lifting platform workbench to achieve multi-point operation.
The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, the faster the lifting speed.
Hamburg North.Novice operators: Due to their lack of understanding or lack of understanding of the operation methods of high-altitude work platforms such as mobile elevators, it is easy for them to make mistakes and cause equipment malfunctions. Operators in this area need to patiently learn and pass training before they can operate and use them.
Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
.Teach you how to choose elevator cables. When choosing elevator cables, you should follow the following two principles: good electrical parameters; During the movement of the cable with the elevator, there will be a section in the middle that undergoes bending deformation due to gravity, causing changes in electrical parameters such as impedance and distributed capacitance of the cable. Poor quality cables have significant parameter changes when subjected to force deformation,
Introduction to Fixed Boarding Bridge Loading and unloading Mobile Boarding Bridge is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed,Hamburg North14 meter aluminum alloy elevator, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.
High altitude operations involving single person work such as high-altitude cleaning. Products, tens of millions of products for you to choose from, professional elevator manufacturers ensure safe trading
The method is that it may cause increased wear and inflexibility of the parts, and it is also important to pay attention to the installation precautions corresponding to the working environment and not be careless. Proper installation, use, and maintenance of elevators are important steps to ensure the normal operation of mechanical equipment. Therefore, when installing the elevator, and carefully assemble and use it.
Regularly check for water accumulation and humidity. It is inevitable for high-altitude work vehicles to drive in rainy and snowy weather, or muddy roads. The bottom and some gaps, as well as the indoor floor, are prone to accumulation of sludge. If the owner does not clean them in a timely manner, this will cause moisture to hide. Therefore, the outer edges of the wheel hub, doors, bottom corners of tree trunks, keyholes and wiper brackets, and other areas of activity should be regularly inspected, and the drainage holes of the doors and various parts should be kept unobstructed to ensure that the car seat covers such as humidity, carpets, and floors, prevent rusting of accessories.
High altitude work requires the use of tool bags,Hamburg North30 meter platform elevator, and heavier and larger high-altitude work tools should be hung on stable components and cannot be placed randomly to avoid the occurrence of high-altitude falling accidents.
new product.Dirty normally closed valve; The solution is to remove the normally closed valve and use cleaning agent or cleaning.
Walking: assisted self-propelled, two wheel traction, self driving, and car modification.
Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
The product has a sturdy structure,Hamburg North6-meter mobile elevator, a large load-bearing capacity, smooth lifting, simple and convenient installation and maintenance, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will share with you some common knowledge about daily maintenance of outdoor elevators: When personnel enter the interior of the lifting platform for maintenance, different power modes can be selected, such as three-phase AC power supply, DC power supply, and internal combustion power supply. With manual hydraulic equipment, lifting operations can be carried out in places with power outages or no power supply, and components can be added. When the platform length is insufficient, it can be extended to the required direction, and then the operating power can be increased. It is a must-have product of modern large-scale construction and equipment, and a necessity for high-altitude safety and civilized production.
The question of how to extend the service life of hydraulic lifting platforms will be briefly discussed here. Many people may not be familiar with this type of equipment especially those who do not know which factories are producing such equipment. It is recommended that friends can search online because many companies selling and producing this type of equipment now have their own official websites, There is a more detailed introduction on maintenance and upkeep knowledge online, and the paint of elevators is not only a beautiful layer; Clothing&# quo; It is also the primary protective layer. Paint can isolate the air, avoid direct contact between steel and air, and slow down the progress of corrosion. However, there are some common knowledge that you are not aware of. Next, let me ask us to explain the tips for anti-corrosion treatment of the paint layer of the lifting channel: choose a trustworthy brand for the paint of the elevator, be cheap, and not greedy. We cannot demand quality, only price. For example, Chenhong, Lipang, and others are trustworthy brands; Apply anti rust paint directly after shot peening. Suitable for general mineral oils and hydraulic fluids, not suitable for aqueous hydraulic fluids. Due to not being constrained by the conditions of handling elevators, large elevators often choose this acid pickling and phosphating method. Suitable for all media, but constrained by acid pickling and phosphating tanks, the elevator cannot be too large; Sand blasting and plastic spraying. Suitable for all media elevators, but restricted by drying equipment, the lifting channel cannot be too large;
Walking: assisted self-propelled, two wheel traction, self driving, and car modification.
Hamburg North.The power unit adjustment, whether it is a scissor type lifting platform or a guide rail type lifting cargo elevator, the longer the lifting time. Therefore which can be adjusted to increase or decrease the hydraulic oil flow rate of the oil cylinder. We can adjust the motor speed or the electro-hydraulic proportional valve to adjust the hydraulic oil flow rate; What factors will affect the lifting speed of hydraulic elevators? The longer the hydraulic oil pipe, during installation, the length of the oil pipe should be minimized as much as possible within the allowable range of the design; On the basis of adjusting the power unit, the size of the oil pipeline can also be adjusted, and corresponding adjustments can be made while ensuring that the equipment meets normal demand and safety.
When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs guardrails or safety nets should be installed on the side facing the air, hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve, throttle valve, hydraulic control one-way valve, and balance valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.