AnthonyPrice o
AnthonyCustomi
AnthonyCustomiand the workbench is evenly loaded to 125% of the maximum load capacity. After lifting 100 times, each load-bearing component must not have deformation or cracks.
After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.
Anthony.Low power consumption: Hydraulic elevators are driven by the pressure generated by their own weight, greatly saving energy. Long term improvement of various brand products such as elevator manufacturers, with complete designated products and quality assurance
Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.
.The downward movement of the hydraulic cylinder (i.e. lowering of heavy objects). The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control one-way valve, throttle valve, and explosion-proof electromagnetic directional valve. To ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve is installed on the return oil circuit to balance the circuit and maintain pressure, so that the descent speed does not change due to heavy objects. The throttle valve regulates the flow rate and the ascending and descending speed. To ensure safe and reliable braking and prevent accidents, a hydraulic control one-way valve, also known as a hydraulic lock, is added to ensure safe self-locking in the event of an accidental rupture of the hydraulic pipeline. An overload sound control alarm has been installed to distinguish between overload or equipment failure.
The hydraulic elevator overflow valve can also generate high noise. When air is mixed in hydraulic oil, the overflow valve is stuck or severely worn the spring of the overflow valve is fatigued and deformed, resulting in unstable pressure regulation of the overflow valve, and the relief time of the overflow valve is too short, it is easy to cause the pilot valve performance of the overflow valve to be partially stable, causing air to vibrate inside the pilot valve and generate noise. So we need to regularly clean the overflow valve. When the overflow valve is damaged or severely worn, it should be replaced.
Set up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.
Wholesale manufacturers of hydraulic cargo elevators have found that the market demand for hydraulic cargo elevators is also increasing. More importantly, some cargo loading and unloading work, as well as decoration, hotels, logistics warehouses, etc., are commonly used in these situations, especially in the decoration industry. I have seen many decoration companies use small hydraulic cargo elevators, which are also specially processed and manufactured, and have some differences from the hydraulic cargo elevators we often see. There are significant differences in structure, shape, and height, and the prices of hydraulic cargo elevators also vary. The hydraulic cargo elevators used in the decoration industry have a low lifting height, some only 2 meters,AnthonyHydraulic cylinder lifting platform, and do not require many materials. He mainly promotes people, not goods, and rarely promotes goods, so the load is small, but not inferior to the use of other hydraulic cargo elevators. He is stable, safe, interpretable, and durable enough to make hydraulic cargo elevators a good helper in the decoration industry. The function of hydraulic cargo elevators is gradually improving with our needs,AnthonyMobile hydraulic lifting platform/lifting platform, and the properties we require are different. Wholesale manufacturers of hydraulic cargo elevators also manufacture according to our requirements.
How to maintain the cleanliness of hydraulic elevators. If more high-quality hydraulic oil is added, it can prevent oil changes or blockage of system components. However, these additives will lose their effectiveness after a period of time.
Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.
Encyclopedic knowledge.Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.
The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.
Reason: The lowering speed valve is out of adjustment. Cleaning method: If the lowering speed valve is adjusted, and if the adjustment is ineffective, replace it with a new valve.
An inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.
When working simultaneously at the upper and lower levels, a tight and firm protective partition, canopy or other isolation facilities must be erected in the middle of the boarding bridge, and workers must wear safety helmets.
Reason: Manual pump and gear pump have severe oil leakage. Cleaning method: Replace the oil pump sealing ring to clean it. Reason: Gear pump is damaged, The oil pumped out has no pressure. Cleaning method: Replace the gear pump to clean the problem. Reason: Lack of hydraulic oil. Cleaning method: Add enough hydraulic oil to clean the problem. Reason: Circuit open. Cleaning method: Check the button and fuse to clean the problem. Reason: Filter blockage. Cleaning method: Replace or clean the problem. Reason: Support valve or electromagnetic directional valve malfunction. There are two situations: the input voltage of the electromagnetic coil is lack of 220V. The solenoid coil is burnt out and the valve core is stuck. Cleaning method: maintenance or replacement can be used to clean the natural descent of the lifting platform. Reason and cleaning method: one-way valve leakage cleaning method: check the check valve in the valve. Assuming there is dirt on the sealing surface of the check valve. Clean the check valve.
Anthony.The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil,AnthonyMovable hydraulic lifting platform, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.
Each box distribution box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.
To consider its capacity, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.