SereniolaelevaWhen conducting a resistance check, it is necessary to disconnect the power supply. At this time, press the up button, and the lifting platform car does not rise. This may be a reversal of the motor after the three-phase power supply is connected, just change the two phase wires of the heavy machine.
From this, it can be seen that the hydraulic lifting platform truck needs to carefully inspect the hydraulic and electrical systems before use, so as to facilitate its use.
.When using a hydraulic lifting cargo elevator, it is necessary to have corresponding inspection routes. If the route malfunctions and the joint becomes loose, it is necessary to turn it on or off properly. In this case, there may be short lines or damaged components. Using a table for inspection is relatively better.
When a hydraulic lifting platform truck malfunctions, it is necessary to take time to prepare accordingly, and provide timely feedback or communicate with the manufacturer at this time. If a voltage range is used to detect a hydraulic lifting platform truck, it is necessary to turn on the power in this case. The circuit schematic is used to measure the electrical circuit. At this time, the voltage value can be measured, and the voltage value can also understand where the fault point is. Therefore, in this case, it is necessary to learn to analyze.
Especially when its pipes are in use, they are quite boring and can roll, they need to be blocked or tied tightly. This is relatively appropriate, so it is necessary to pay attention to these details during use. Especially for unmanned protective lifting platforms, it is not allowed to carry people during use, and it is strictly prohibited to carry people. If the electric lifting platform truck carries people during use the lifting platform is equipped with railings or anti crack valves, the main focus is on whether it is normal and whether there is noise during use. When faults are found which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.
To understand the operation of the mechanism, timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation, it is necessary to disassemble or adjust the rotating mechanism. In this case, it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course,Sereniola10 meter hydraulic lifting platform, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.
The manual hydraulic scissor platform vehicle has the following characteristics: suitable for long-distance transportation; Treadable feet and protective devices; Lightweight and easy to lift; Unique caster design ensures safety; The engineering handle design ensures comfortable operation for the operator.
To understand the operation of the mechanism, the main focus is on whether it is normal and whether there is noise during use. When faults are found, timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation, it is necessary to disassemble or adjust the rotating mechanism. In this case it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.
How much does it cost?.In the past, in large workshops, if goods had to be transferred from one place to another, it would be very expensive. For loading, unloading, and transferring 2 tons of goods it would require 10 people to work continuously for several hours, using forklifts to operate and multiple forklifts to work simultaneously for one or two hours. Moreover, using forklifts also required professional forklift drivers, and the cost of using them was often high. Is there any way to do this, Can it meet both rapid loading and unloading of goods and low-cost needs? Of course there is,SereniolaHydraulic lifting platform, that is the application of fixed loading and unloading platform trucks. A fixed loading and unloading platform truck is an auxiliary equipment that mainly completes the rapid loading and unloading of goods. It has an adjustment function, and the truck has a certain height to cross when transporting goods from the warehouse to the truck. However, a fixed loading and unloading platform truck can adjust the height and serve as a bridge to connect the truck and warehouse, meeting a large number of cargo handling needs, But such a large workload requires only one operator to operate, greatly saving labor costs and manpower, improving the production efficiency of the enterprise. Professional hydraulic lift truck manufacturer with high prices, service on-site settlement, and honest operation!
I believe many people are familiar with mobile elevating platform vehicles. In daily life, we often see that this elevating platform vehicle is used in many fields, the hydraulic lifting platform truck uses a dual protection structure which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform truck will be safer during operation. The process of operating the hydraulic lifting platform truck should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
The electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
property right.When using, the weight should be evenly distributed, mainly in the center of the countertop. However, for special cases, partial loading is allowed, but the longitudinal load cannot exceed half of the rated load. The horizontal load should not exceed one-third of the rated load, so this detail needs to be noted during use.
Firstly, an obvious advantage is its high safety performance. The guide rail hydraulic lifting platform car adopts heavy-duty chain transmission, hydraulic explosion-proof oil pipes, safety devices to prevent overloading, multiple limit switch protection, door and power outage protection, leakage protection,Sereniola10 meter hydraulic lifting platform, the safety factor of the guide rail hydraulic lifting platform car is still very high, much higher than that of ordinary platform cars.
When using, the weight should be evenly distributed, mainly in the center of the countertop. However, for special cases, partial loading is allowed, but the longitudinal load cannot exceed half of the rated load. The horizontal load should not exceed one-third of the rated load, so this detail needs to be noted during use.
Sereniola.Of course, the hydraulic lifting platform truck uses a dual protection structure, which can make the work relatively safer. When lifting, so that the lifting platform truck will be safer during operation. The process of operating the hydraulic lifting platform truck should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
The electric lifting platform truck needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
In the current society, pneumatic tires or polyurethane wheels are used in the market, so this type of lifting platform car has a very good texture and can be used in places such as home floors during use. Therefore, this type of mobile lifting platform car will not cause damage to the ground during use, making it very convenient to use. The elevator is made of manganese steel, especially its theme frame, which is not easy to corrode during use and is important for convenient storage.