Barletta Hydra
Barletta PriceThe lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.
Hydraulic cargo elevators have been used in some high-altitude operations in recent years, and now some hydraulic cargo elevators are gradually mentioned as large machinery such as tower cranes, becoming a better choice for some high-altitude operations. However, there are still certain limitations, such as height and improving the quality of goods, which have certain constraints.
Barletta .When working simultaneously at the upper and lower levels, a tight and firm protective partition, canopy or other isolation facilities must be erected in the middle of the boarding bridge, and workers must wear safety helmets.
There are many reasons for unstable workbench descent, such as overload, unstable support severe eccentric load, hydraulic oil impurities etc. In response to the above reasons, it can be solved by reducing the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.
.Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location,Barletta Hydraulic small lifting platform, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.
There are many reasons for unstable workbench descent, such as overload, unstable support, severe eccentric load, hydraulic oil impurities,Barletta Mobile hydraulic lifting platform, etc. In response to the above reasons, it can be solved by reducing the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.
There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.
Reason: The lowering valve is not tightly closed. Cleaning method: Check if the lowering valve is powered on. If there is no power supply, clear the malfunction of the lowering valve itself or replace the lowering valve. It is necessary to keep the valve of the lowering valve clean and flexible.
The above are common situations, and there are many other reasons based on the actual situation. Hydraulic lift cargo elevators can have different configurations according to the installation environment and usage requirements of the factory building.
Electrical equipment or component failures. Hydraulic elevator manufacturers tell you that the main reasons for high noise generated by electric motors are: bent or severely worn motor rotors, or damaged bearings, which cause electric motors to sweep and produce noise; The cooling fan of the electric motor is damaged or not firmly fixed, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.
install.Before installation, the installation personnel should confirm the infrastructure such as the foundation and shaft,Barletta Small hydraulic lifting and leveling, pay attention to alignment, leveling, and alignment points, and confirm that the foundation meets the requirements before construction.
Users should arrange dedicated personnel to operate hydraulic elevators, formulate usage details and safety precautions for hydraulic elevators based on their own situation, and hang them on the
The undercut length of the weld mm should not exceed 10% of the weld seam, and the depth should not exceed 0.4mm.
The contact of the travel switch must be firmly opened and closed, it is necessary to replace it immediately. The protection of steel wire ropes should strictly follow the rules of GB5144-85.
The above are common situations and there are many other reasons based on the actual situation. Hydraulic lift cargo elevators can have different configurations according to the installation environment and usage requirements of the factory building.
The contact of the travel switch must be firmly opened and closed, and the contact crater should be polished in a timely manner.
Barletta .Regularly inspect the hydraulic lifting equipment of the upper and lower materials to ensure the safety of the rail type elevator and the safety of the material supply to the rail type lifting platform.
Remember not to overload, overload is the root cause of many faults.
The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.