FlorenceFoot operated hydraulic lifting platformStructural parts of routine maintenance knowledge

Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.

Secondly, the maintenance of the guide rail type hydraulic lifting platform is also very simple, using oil cylinders and chain transmission, with very few moving components, so the maintenance workload is not very high. Moreover, this type of lifting cargo elevator has a very compact structure and uses fewer bearings resulting in a longer service life.

Florence.Of course, the hydraulic lifting platform uses a dual protection structure, which can make the work relatively safer. When lifting, so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.

The drive motor can stop the movement of the rack on the pillar.

.Later, when there is a major malfunction of the lifting platform, it should be repaired by professional personnel as soon as possible. After the malfunction occurs,FlorenceFixed electric hydraulic platform, it should not be used again to avoid accidents, personnel and property losses.

Tail signature:

Replace with

Small typesetting Copyright Shu ICP Bei No. 11019783-1

To understand the operation of the mechanism the main focus is on whether it is normal and whether there is noise during use. When faults are found, timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation it is necessary to disassemble or adjust the rotating mechanism. In this case, it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.

When using the elevator, it is strictly prohibited to lift them.

Honesty is the foundation.Everyone knows that construction elevators are used during the construction process because they have stability, and are widely used in the field of high-rise buildings due to their small size and other advantages.

Check the hydraulic oil quality and level. When the lifting platform is raised to a high position, the hydraulic oil level should be 40-50 millimeters higher than the bottom of the oil tank. When the color of the hydraulic oil darkens, the oil becomes sticky, or there are foreign objects such as gravel in the oil, the hydraulic oil should be replaced in a timely manner. The hydraulic system of the lifting platform should be checked for hydraulic and pipeline connections. If the pipeline is damaged, it should be replaced immediately; When there is looseness in the connection part tighten the pipe joint.

When the motor overheats, it should be stopped immediately, and after troubleshooting, it should continue to operate. The motor bearings should be in good condition.

The reduction gearbox, gearbox, and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table.

Affordable price.Leading spaces in blank lines Full width: Font size: Replace: Replace

Of course, the hydraulic lifting platform uses a dual protection structure, which can make the work relatively safer. When lifting,FlorenceElectric lifting hydraulic platform, an appropriate working surface can be selected, so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course,FlorenceDual track hydraulic lifting platform, the hydraulic electrical system does not need to be adjusted in this situation.

Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors, wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.

Florence.The drive motor can stop the movement of the rack on the pillar.

Of course, when choosing a lift, it is also necessary to consider its production. If a manufacturer has a large production capacity, it indicates its strong strength, especially the construction lift has relatively high requirements for production technology. Therefore, when making a purchase, it is important to consider the factory building and process of its production, all of which are very important.

Convert to Simplified Chinese Convert to Traditional Chinese without converting the number of blank lines between paragraphs before and after: