DenverElevator
DenverHydrauliWhen using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level 5 please stop using it; When the lifting height exceeds 10 meters, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platform
What are the methods for reducing shaking on lifting platforms? Reducing the shaking of the lifting platform can reduce the psychological obstacles of the operators,DenverScissor fork hydraulic lifting platform, ensure the smooth progress of the operation, and also greatly help improve safety. Warm reminder: safety, do not operate blindly. Lifts are widely used in many places, and their working principles vary. Today, we will analyze the working principles of elevators. The types of elevators are generally divided into the following: fixed elevators, This type of elevator uses hydraulic oil cylinders and pump stations to transmit power, in the form of a scissor fork type. According to customer requirements, the length of the support rod for the scissor fork,DenverFreight elevator type hydraulic lifting platform, the number of layers, the angle of the angle axis, and the expansion and contraction of the oil cylinder complete the lifting operation. Its advantages are large load-bearing capacity, stable lifting, and high safety.
Denver.High altitude work should always use tool bags. Tools with larger boarding bridges should be tied to sturdy components with ropes,DenverHydraulic lifting platform lifting cargo elevator, and should not be placed randomly to prevent accidents caused by falling from a height.
The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point the oil seal or straightening rod must be replaced in a timely manner.
.I believe many people want to know about the maintenance issues of guide rail hydraulic lifting platforms, as it is related to their service life. During use frequently check the connection of each part. If loose, tighten it. When the body is under pressure, and the positions of cables, oil pipes, and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws, and the hydraulic cargo elevator after reinforcement has robustness and safety.
When placing materials on the platform, they should be placed in the middle of the platform as much as possible. The weight of the goods should be within the standard load range of the equipment, and the volume of the goods should not exceed the platform size of the equipment. Otherwise, materials and lifting platforms may be injured and dangerous accidents may occur. High priced and various specifications of elevator manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!
The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.
The hook or rope of the seat belt should be hung on a sturdy and sturdy component or a steel wire rope specifically designed for hanging the seat belt. Prohibit hanging on moving or unstable objects.
After 5000 hours of elevator operation, carry out medium maintenance on the mechanical and electrical systems.
recommend.Do you know the classification of simple cargo elevator lifting platforms? The manufacturer of the hydraulic cargo elevator is here to inform you.
The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.
Separate: Loading and unloading on different platforms.
Hydraulic elevator manufacturers remind us that the basic principle of the hydraulic elevator speed control circuit is that the system often needs to adjust the movement speed of the hydraulic cylinder and hydraulic motor to adapt to the working cycle needs of the main machine. The speed of hydraulic cylinders and hydraulic motors depends on the displacement and input flow rate. It can be seen that changing the flow rate or displacement can affect the speed of the cylinder and motor.
Installation material list.The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.
All high-altitude operations must first build scaffolding or take measures to prevent teams from falling before boarding the vehicle bridge.
Do not use hydraulic lifting equipment with malfunctioning issues. The problem should be resolved before carrying cargo.
Denver.The hydraulic oil used in the system has the same brand, and after each cleaning, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.
The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.
The undercut length of the weld mm should not exceed 10% of the weld seam, and the depth should not exceed 0.4mm.