HagueElectric 
HagueTwo ton h
HagueCylinder Remove and disassemble the hydraulic lift cargo elevator lowering valve, blow out the plunger with compressed air, then install it and reinstall it.
Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
Hague.When the motor connection of the elevator is incorrect, when a coil, coil group, or one phase winding group is connected in reverse, it can cause serious three-phase current imbalance and cause the winding to overheat.
Good stability: The overflow valve can prevent excessive system pressure during upward movement. Emergency manual valve: In case of power failure, it can cause the elevator car to descend to the nearest floor position and open the door. Manual pump: When the system malfunctions, the manual pump can be operated to pump high-pressure oil to raise the car to the nearest floor position; Tank oil temperature protection: When the oil temperature in the tank exceeds the standard setting value, the oil temperature protection device sends a signal to suspend the use of the elevator. The elevator can only be started when the oil temperature drops.
.When installing, disassembling, and adjusting the rotating mechanism, it is important to ensure that the centerline of the reducer of the rotating mechanism is parallel to the centerline of the gear, and its meshing surface is not less than 70%. The meshing clearance should be suitable.
Pay attention to checking each steel wire rope for broken wires and loose strands. If it exceeds the relevant regulations,HagueGuide rail hydraulic lifting platform, it must be replaced immediately. The maintenance and upkeep of steel wire ropes should strictly follow the 85 regulations.
The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, the faster the lifting speed.
How to install and use the bearings of the elevator? During the process of using the bearing device of the elevator, we cannot always ensure that the bearing device has the right orientation, which inevitably leads to some devices not being in place or bearing displacement. Once these problems occur in the device it will cause the clearance between the bearings to become too small, and then make it impossible for the inner and outer rings of the bearings to be in the same rotation center. So it is necessary to use specialized tools when installing bearings, and in the future, it is also necessary to use a testing instrument to test the bearing installation, in order to ensure the success of the bearing installation.
A sign of slowing down has occurred. After the speed slows down, consider the hydraulic oil flow rate first. The factors that affect hydraulic oil flow include: hydraulic pipelines, hydraulic valves, hydraulic oil pumps, motor speed control assembly, etc. The following editor will introduce to you the four reasons for the slower speed and the mediation methods.
The reduction gearbox, gearbox, external meshing gear and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table. Professional scissor lift manufacturer with high prices, service, on-site settlement and honest operation!
Latest consultation.Use a heavy crane to lift the cage and lift it from above the standard section
The sinking of a cargo elevator is a phenomenon where the table surface drops due to gravity after a certain period of time when it rises to a designated position. Of course, the editor summarizes the ultimate solution.
The reduction gearbox, gearbox, external meshing gear and other parts as well as the hydraulic oil, are all carried out according to the requirements in the table. Professional scissor lift manufacturer with high prices, on-site settlement, they must be promptly eliminated. For a long time,HagueHydraulic scissor type lifting platform, the manufacturer of scissors lift has never changed hands to avoid price difference, and the price is 20% higher than the market value! More than one ton is more expensive!
Promotion.What are the common faults of hydraulic lifting platforms? The hydraulic lifting platform's oil cylinder is severely damaged, and uneven damage to the inner sealing ring or obstacles inside can easily cause uneven stress, resulting in uneven lifting height of the oil cylinder. It is recommended to carefully check whether the oil cylinder is normal.
Gear pump worn, aged or damaged; The solution is to replace the gear pump.
Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter,HagueHydraulic lifting platform, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
Hague.Before using the machine, the staff should carefully inspect the hydraulic and electrical systems to ensure that there are no leaks or bare leaks before use.
What are the common faults of hydraulic lifting platforms? The hydraulic lifting platform's oil cylinder is severely damaged, and uneven damage to the inner sealing ring or obstacles inside can easily cause uneven stress, resulting in uneven lifting height of the oil cylinder. It is recommended to carefully check whether the oil cylinder is normal.
Each department's electric brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than 50%