San FranciscoF
San FranciscoHConsidering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators,San FranciscoHydraulic lifting platform, to avoid any worries about after-sales service.
Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.
San Francisco.Usage and instructions for steel wire ropes in elevators: The steel wire ropes of the steel wire ropes require very high strength, usually made of high-quality carbon steel with a carbon content of 0.5% -0.8%. They are widely used as transmission components in elevators. Due to its large load-bearing capacity, light weight, smooth operation,San FranciscoMobile hydraulic lifting table supply, no noise, suitable for high-speed transmission, high strength, strong overload capacity and reliable operation, it has become a commonly used rope for hydraulic elevators.
Oil leakage from the oil cylinder: If it is a problem with the sealing ring, it is recommended to replace it with a new one.
.The hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.
There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.
When encountering signs of overheating in the electric motor, it is necessary to park the car in a timely manner clean the problem, and continue running. The motor bearings should be smooth and outstanding.
After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally, due to overload, insufficient power supply, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.
When working at heights,San FranciscoPrice of lifting hydraulic platform, except for relevant personnel, the greater the shaking. When using it at a working height of 10 meters, if possible, please use safety protection measures
recommend.Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.
When the hydraulic oil of the equipment is insufficient, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.
Oil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder, it is recommended to replace it with a new one.
This paper briefly introduces some matters that should be paid attention to in the selection of oil tank for hydraulic elevators. The main functions of the hydraulic oil tank for elevators in the hydraulic systems of hydraulic machinery such as elevators and hydraulic elevators are oil storage, heat dissipation, separation of air contained in oil and elimination of foam.
Honesty is the foundation.An inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed dust or rust is poor, and the device will produce; Buzz&# quo; Noise.
If working on a grid like platform, wooden boards should be laid to prevent tools and equipment from falling.
Next, there should be no dirt present. If there is dirt, it is necessary to wash it off with gasoline or thinner.
San Francisco.The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump, conduct maintenance, cleaning, and replace the cleaning hydraulic oil to clean.
Voltage too low: Measure the starter voltage, with an allowable fluctuation range of± 10%.
The installation personnel should have the qualification for installing hydraulic cargo elevators, carefully implement the special construction plan for installation and construction, and provide safety technical disclosure to the installation personnel for technical design.