Wichito4-meter
WichitoWorkshoA type of elevator equipment consisting of a walking mechanism hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.
Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten the inner hexagon. Afterwards, remove the motor shaft key.
Wichito.Ensure excellent power supply at the installation site, install a separate distribution box, and the electrical leakage switch must meet the requirements for construction elevators when using the distribution box. If the installed construction elevator is variable frequency, the leakage switch should be compatible with the frequency converter when selecting it.
Aging and deterioration of hydraulic oil; The solution is to replace the hydraulic oil. A specialized product manufacturing enterprise that integrates research and development, as well as service. A long-term professional elevator manufacturer
.Single column aluminum alloy elevator: This series of products is indoor and widely used for high-altitude operations in various industries such as star hotels and large supermarkets. It has lifting balance, easy operation, and can enter general lobbies. It can enter and exit the elevator at will with low power consumption, and does not harm the ground during work. It can be used for wall work and exploration work, and there are no dead corners during work. The single column aluminum alloy electric elevator, equipped with gantry cross frame accessories is very suitable for maintenance work in cinemas, auditoriums, etc.
Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten the inner hexagon. Afterwards, remove the motor shaft key.
Three column aluminum alloy elevator: Three sets of masts support the synchronous lifting of the working platform, and the support structure is the same as that of a single masted platform, with super large load capacity and work stability. The overall lifting guardrail device has good strength and greatly reduces the height of the entire machine during transportation. It is very convenient for loading and unloading, and can be assembled or disassembled in one lift.
4: Small scale pneumatic or electric rust removal is based on the principle of using air compression to generate friction or electromagnetic effects to polish and remove rust on the surface of spiral elevators. It can be used for precision instrument push rods or for enterprises that require micro operation of spiral elevators.
What is the new price for fixed elevators? Fixed elevators are currently very popular in the market. Due to different manufacturers, materials, rated loads, and brand awareness, the prices of fixed elevators produced in the current domestic market vary. The prices of fixed elevators are: rated loads of 1-5 tons, an elevation of 7 meters, a table size of 2500mm * 2000mm, and around 27000-45000 yuan; The rated load is 1-3 tons, the lifting height is 0 meters the table size is 2300mm * 2000mm, and the price is around yuan. The rated load, lifting height, and table size of each fixed elevator vary in price. (Specific bearing capacity and lifting height can be designed and customized according to user requirements)
When working at heights exceeding 1.5 meters, safety nets or safety belts must be used.
Administration.During the use of hydraulic elevators, if not properly operated, there will always be problems. Many customers have reported that hydraulic elevators sometimes cannot be lifted. If the hydraulic lift pump can continue to work, other issues need to be considered. Below, the editor will explain the reasons for the hydraulic lift pump station not being oiled and solve the reasons for the hydraulic lift pump station not being oiled, as well as the solutions for mobile elevators The analysis of the pump station of hydraulic elevators such as guide rail elevators is as follows: the motor power supply is abnormal or reversed; The solution is to correctly connect the motor power supply or adjust the steering mailbox to ensure there is no hydraulic oil or insufficient oil; The solution is to add hydraulic oil.
The loading and unloading mobile boarding bridge has become a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.
The current should exceed the rated current, and even cause the motor to stop on its own. If the shutdown time is slightly longer and the power supply is not cut off, the winding will not only overheat severely, but also burn out. When a star connected motor is mistakenly connected into a triangle,WichitoMobile elevator, or a motor with multiple coil groups connected in series into a branch is mistakenly connected into two parallel branches, it will cause the winding and iron core to overheat, and in severe cases, the winding will be burned out.
Connect the motor naturally to the elevator. When connecting, it is necessary to ensure that the concentricity of the elevator output shaft and the motor input shaft is consistent, and the outer flanges of the two are parallel. Inconsistent alignment can lead to motor shaft breakage or elevator gear wear.
ranking.What is the solution to the problem of surface rust on the spiral elevator? The deficiency is that sandpaper has a significant loss on the spiral elevator itself.
Loosening: The newly processed and assembled components of high-altitude work platform equipment such as mobile elevators have a tendency to have geometric shapes and matching dimensions. In the early stages of equipment use, due to the influence of alternating loads such as impact and vibration, or factors such as heat and deformation, coupled with rapid wear and tear, it is easy to cause the previously fastened components of high-altitude work platform equipment such as mobile elevators to become loose.
The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, the faster the lifting speed.
Wichito.Characteristics of hydraulic elevators: Hydraulic lifting platform products are divided into curved arm hydraulic lifting machines, scissor fork hydraulic lifting machines, mast hydraulic elevators, and straight arm hydraulic elevators according to their working modes. Hydraulic elevator is a replacement product of folding arm elevator (lifting platform) and scissor fork elevator (lifting platform). It can be widely used for the decoration and decoration of stations, docks, airports, hotels, posts and telecommunications, municipal gardens, garages, public building facades, or the installation and maintenance of power systems etc. This elevator has the advantages of light weight, self-propelled walking, electric starting, self supporting legs, simple operation, large working area, and especially the ability to cross obstacles for high-altitude operations.
Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten the inner hexagon. Afterwards, remove the motor shaft key.
Many people believe that the mechanical strength of the elevator itself is relatively high when using it, so during the installation process, there is no