Darbus Hydraul
Darbus 10 ton Activate the up button. When the board reaches a high height, the overlap plate will automatically straighten and be parallel to the panel. At this time release the up button and the panel will automatically descend until it connects with the carriage. Once confirmed, the operation can begin. After waiting for the homework to be completed press the up button to drive the vehicle away. Release the button panel and it will automatically descend to its original state, parallel to the cargo platform.
The lip plate is connected to the platform using a full length shaft, which has high strength and good reliability.
Darbus .The overall module of the water inlet pipe of the hydraulic boarding bridge must have a reasonable hydraulic system during the application process, so that the equipment has excellent airtightness and a long service life, and the height of the equipment is fixed
Regarding the year-end maintenance of the boarding bridge, check all hydraulic pipelines and joints to ensure that they are not damaged or loose. All joints must be tightened; Discard all hydraulic oil and replace it with new oil to avoid continuing to use old oil. Otherwise, blow out the plunger with compressed air, and then reinstall it. To use a fixed hydraulic boarding bridge,Darbus Simple boarding bridge, it is necessary to have a basic understanding of its basic knowledge. Below, Jinan Zhongding Elevator will analyze it for everyone: To operate a fixed hydraulic boarding bridge, fix it on both sides of the carriage, and then reverse the truck to the front of the platform until it meets the anti-collision rubber blocks on both sides of the fixed hydraulic boarding bridge. Then, brake the truck. Turn on the power switch on the electric control box, and the professional boarding bridge factory has stable, safe, reliable, and can achieve maintenance free performance. The technical level has reached the domestic level and the international advanced level of similar products
.Secondly, before using the hydraulic boarding axle, it is also necessary to check if there is any oil in the reducer, abnormal noise, and excessive temperature rise in the housing. If there is any oil leakage, it is necessary to check the oil level in the housing, if there is insufficient oil and add oil. If there is any abnormal noise or rapid temperature rise, repair it in a timely manner
Firstly, before using the equipment (shè bè i), it is necessary to check whether there is water accumulation in the points, and then confirm whether the fasteners are damaged or loose. If a fault is detected, necessary repairs and replacements need to be carried out. Check all control devices (zhu ā ng zhì） Whether the operation is normal, whether the switch and governor are in good condition,Darbus Container dedicated boarding bridge, whether the movement and working speed are stable, and whether the display is normal
The equipped brake pads can effectively prevent the shifting of the boarding bridge during truck loading and unloading.
High strength& quot; U& quot; The design of the shaped beam can ensure its high load and long-term operation without deformation.
The fixed boarding bridge of the service platform is immediately installed on the outer edge of the unloaded service platform during the entire installation process. When applied, and most of the buildings do not need to be modified in terms of structure.
A tractable mobile boarding bridge is a type of mobile boarding bridge that can be towed by forklifts, tractors, etc. It is developed by combining the technology of flat trailer traction frames. The front section is equipped with heavy-duty universal wheels and detachable traction rods that can be rotated to both sides. When movement is needed, the universal wheels can be rotated to the lower end and a traction rod can be installed, which can easily and conveniently achieve traction movement.
wholesaler.Using a hand operated hydraulic pump as power, the height adjustment of the boarding bridge can be achieved without the need for external power supply.
Regarding the year-end maintenance of the boarding bridge, check all hydraulic pipelines and joints to ensure that they are not damaged or loose. All joints must be tightened; Discard all hydraulic oil and replace it with new oil to avoid continuing to use old oil. Otherwise, the moving components in the system will accelerate wear and tear. Remove and disassemble the lowering valve, blow out the plunger with compressed air,Darbus Fixed hydraulic boarding bridge, and then reinstall it. To use a fixed hydraulic boarding bridge, it is necessary to have a basic understanding of its basic knowledge. Below, Jinan Zhongding Elevator will analyze it for everyone: To operate a fixed hydraulic boarding bridge, first open the rear door of the truck, fix it on both sides of the carriage, and then reverse the truck to the front of the platform until it meets the anti-collision rubber blocks on both sides of the fixed hydraulic boarding bridge. Then, brake the truck. Turn on the power switch on the electric control box and the professional boarding bridge factory has stable, safe, reliable, and can achieve maintenance free performance. The technical level has reached the domestic level and the international advanced level of similar products
Assuming that the manufacturing quality of fixed hydraulic boarding bridges is not satisfactory, the reasons for their shortcomings are mostly preventive repairs, and there are usually fewer elements of abnormal operation.
The boarding bridge is convenient for unloading, has strong stability, and low maintenance costs. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic, the boarding bridge is composed of mechanical systems, hydraulic systems, and electrical systems. Fully hydraulic drive, easy to operate and reliable to operate. The lip plate is connected to the platform using a full length shaft, which has high strength and good reliability. The use of imported seals ensures excellent sealing performance of the hydraulic system. Adopting imported integrated modular hydraulic station, with good sealing performance and long service life. Monthly maintenance of the landing bridge of the lifting platform. The landing bridge, like other handling tools, sticky or has sand and gravel and other foreign matters, it should be replaced in a timely manner; Each part should be filled with some oil separately, which can extend the service life of the bearing.
Test method.Regarding the year-end maintenance of the boarding bridge, check all hydraulic pipelines and joints to ensure that they are not damaged or loose. All joints must be tightened; Discard all hydraulic oil and replace it with new oil to avoid continuing to use old oil. Otherwise, the moving components in the system will accelerate wear and tear. Remove and disassemble the lowering valve, blow out the plunger with compressed air, and then reinstall it. To use a fixed hydraulic boarding bridge, it is necessary to have a basic understanding of its basic knowledge. Below, Jinan Zhongding Elevator will analyze it for everyone: To operate a fixed hydraulic boarding bridge, first open the rear door of the truck, fix it on both sides of the carriage, brake the truck. Turn on the power switch on the electric control box and the professional boarding bridge factory has stable, safe, reliable, and can achieve maintenance free performance. The technical level has reached the domestic level and the international advanced level of similar products
The guide sleeve has air holes, sand holes, shrinkage, and other conditions. Generally, there is a problem with the casting which is the quality of the oil cylinder itself. At this time, it is necessary to find a manufacturer to replace the new boarding bridge. Normally, this situation does not occur in the casting oil cylinder. The above two reasons are due to the occurrence of excessive oil leakage, and frequent inspections should be conducted in these two areas. Hydraulic loading and unloading bridge is a specialized auxiliary equipment that maintains rapid loading and unloading of goods during the application process. The height adjustment function of the equipment makes the bridge in the middle of the truck guide sufficient to be built. Lifting platforms, trucks, and hydraulic loading and unloading bridges are commonly used cargo loading and unloading equipment.
The lifespan can reach twice that of the tires on the rigid suspension boarding bridge. In addition, the wear and tear of the rear axle tires varies greatly. Under the same operating conditions, tires that do not use self steering cars wear three to four times faster. It is obvious that the additional cost incurred by using the self steering boarding bridge will soon be compensated. Semi trailers using self steering boarding bridges are flexible in operation and require a narrow road width when turning, suitable for various occasions. Experiments have shown that the turning radius of a semi trailer with the same body length and load can be reduced by about 10% when using a self steering car.
Darbus .Precautions for safe use of fixed hydraulic boarding bridges When operating the machine, it is necessary to operate it in a safe manner. Unfamiliar personnel should not do so. During the operation, do not stand bystanders around. Be sure to carry the load according to the rated load, not the weight of the goods alone. This is something that customers and friends should know. If there is detachment or deformation of the boarding bridge, please do not use it to avoid serious accidents. The boarding bridge is mainly an auxiliary device for loading and unloading goods, which greatly improves the loading and unloading power (referring to the amount of work done by objects in a unit of time), and is something that logistics companies (Company) cannot do less. If the power of the boarding bridge operation (zuò yì) is to be durable, no problems can appear during the operation. Perhaps the problems can be dealt with in a timely manner. Regarding identifying the cause of the hydraulic system problem of the boarding bridge, It is beneficial for us to use the boarding bridge correctly and provide homework
2. The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages. The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.
The lifespan can reach twice that of the tires on the rigid suspension boarding bridge. In addition, the wear and tear of the rear axle tires varies greatly. Under the same operating conditions, tires that do not use self steering cars wear three to four times faster. It is obvious that the additional cost incurred by using the self steering boarding bridge will soon be compensated. Semi trailers using self steering boarding bridges are flexible in operation and require a narrow road width when turning, suitable for various occasions. Experiments have shown that the turning radius of a semi trailer with the same body length and load can be reduced by about 10% when using a self steering car.