DresdenDouble shear hydraulic lifting platformWhat should be paid attention to when using

and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.

Dresden.When working on the dam crest, steep slopes, roofs, cliffs, towers, suspension bridges and other dangerous edges, safety nets or protective railings should be installed on the side facing the air. Otherwise, workers must use safety belts. Ice, snow, gravel, and soil on the steep slopes of steep cliffs, boarding bridges, or sidewalks must be regularly cleaned, and a 1-meter high railing must be installed on the outer side. Install an 18 centimeter high side board or soil ridge on the inner side of the railing to prevent falling objects from injuring people.

The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.

. There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow,Dresden3-meter hydraulic lifting platform, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, exhaust and clean the valve body several times, repair or replace the spring,Dresden12 meter hydraulic lifting platform, reduce the flow of the remote control port, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. 5. The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.

The installation personnel should have the qualification for installing hydraulic cargo elevators, carefully implement the special construction plan for installation and construction, and provide safety technical disclosure to the installation personnel for technical design.

Hydraulic cargo elevators have been used in some high-altitude operations in recent years, and now some hydraulic cargo elevators are gradually mentioned as large machinery such as tower cranes, becoming a better choice for some high-altitude operations. However there are still certain limitations, such as height and improving the quality of goods, which have certain constraints.

Separate: Loading and unloading on different platforms.

The hydraulic pump also has an impact on the flow rate of hydraulic oil. If the hydraulic pump is used for a long time, it is also prone to problems. When the speed of the hydraulic lifting table slows down, it is necessary to check whether the oil supply of the hydraulic pump is firm and firm.

Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.

The cheapest.Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.

The undercut length of the weld mm should not exceed 10% of the weld seam, and the depth should not exceed 0.4mm.

Introduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it, forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, improve the efficiency of loading and unloading operations, speed up the flow of materials, and obtain greater economic benefits.

When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.

Management Department.Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.

Many operating factories often require the use of hydraulic cargo elevators, which can be lifted and lowered, it will be helpful for future maintenance. The power unit of the fixed chain elevator for hydraulic lifting of cargo elevators drives the hydraulic oil to generate pressure, causing the oil cylinder to move back and forth to drive the lifting platform,DresdenPrice of lifting hydraulic platform, thus achieving the adjustment of lifting speed. The power unit adjustment, whether it is a scissor type lifting platform or a track type lifting platform, which can be adjusted in size to increase or decrease the hydraulic oil flow rate of the oil cylinder Adjustable motor speed or electro-hydraulic proportional valve to adjust hydraulic oil flow rate; The longer the oil pipe and hydraulic oil pipe, the longer the rise time. So during installation, try to minimize the length of the pipeline within the allowable range of the design; On the basis of adjusting the power device, the size of the oil pipeline can also be adjusted, and corresponding adjustments can be made while ensuring that the equipment meets normal demand and safety.

The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators, curved arm elevators, car mounted elevators, etc. Their common feature is the hydraulic principle for operation, because the stability of the hydraulic system can bring better user experience and safer operation to the equipment, which has been favored by many users.

Dresden.The installation personnel should confirm and count the equipment details, confirm that there are no omissions in the shipped equipment details, check if the tools are complete, and ensure the smooth progress of the installation process.

The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, and frequent separation and suction can also produce high noise.

Emergency descent device: When a power driven chain elevator loses power, there should be a device to make the workbench emergency descend.