Stability: The workbench should evenly withstand 125% of the MAX load capacity and be stable at the MAX elevation.
If the circuit of the device is not disconnected or lowered,KetaiElectric hydraulic lifting platform truck, it is necessary to check the fuse for repair and replacement.
Ketai.Hydraulic elevators have two working periods and two end dwell times within a working cycle. Working hours refer to the period of lifting and falling objects. The suspension period refers to the period during which the machine temporarily stops working at the required height of rest. Therefore, each working period is divided into three different stages: starting constant speed lifting, and braking.
Hydraulic lift cargo elevators belong to high-altitude work equipment. Small shaking of the scissor type structure is normal,KetaiHydraulic lifting platform, but excessive deviation is a symptom. It is necessary to find the cause and make correct judgments in a timely manner. Generally speaking operations above 8 meters are generally allowed. Due to its own weight, devices above this height begin to vibrate in different ranges. The vibration range depends on factors such as weight, lifting height, and intensity of high-altitude operations.
.Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.
Oil leakage is a common malfunction. Due to loose joints or damaged sealing rings, oil leakage may occur. Therefore, this fault can be solved by tightening the oil leakage joint or replacing the damaged sealing ring.
The hydraulic oil used in the system has the same brand, and the oil temperature is between 45~80 ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.
Hydraulic elevators and load-bearing oil cylinders can directly act on the foundation pit, and brick or brick concrete structure shafts.
The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.
Where can I find it?.Reason: Manual pump and gear pump have severe oil leakage. Cleaning method: Replace the oil pump sealing ring to clean it. Reason: Gear pump is damaged, The oil pumped out has no pressure. Cleaning method: Replace the gear pump to clean the problem. Reason: Lack of hydraulic oil. Cleaning method: Add enough hydraulic oil to clean the problem. Reason: Circuit open. Cleaning method: Check the button and fuse to clean the problem. Reason: Filter blockage. Cleaning method: Replace or clean the problem. Reason: Support valve or electromagnetic directional valve malfunction. There are two situations: the input voltage of the electromagnetic coil is lack of 220V. The solenoid coil is burnt out and the valve core is stuck. Cleaning method: maintenance or replacement can be used to clean the natural descent of the lifting platform. Reason and cleaning method: one-way valve leakage cleaning method: check the check valve in the valve. Assuming there is dirt on the sealing surface of the check valve. Clean the check valve.
Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.
The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness, it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.
The contact of the travel switch must be firmly opened and closed, and the contact crater should be polished in a timely manner.
Discount.Mobile is a type of cargo heavy machinery equipment with good adjustment reliability and wide application fields, it will affect the speed. The above is the knowledge about adjusting the lifting speed of hydraulic cargo elevators, hoping to be helpful to everyone. Long term improvement: The manufacturer has a complete range of products, excellent quality and discounted prices
The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators, curved arm elevators, car mounted elevators, etc. Their common feature is the hydraulic principle for operation, because the stability of the hydraulic system can bring better user experience and safer operation to the equipment, which has been favored by many users.
Ketai.Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.
Reason: Cleaning method for internal leakage in the oil cylinder: Replace the sealing element of the oil cylinder. The lifting platform does not lower. Reason: The lowering valve is malfunctioning. Cleaning method: When pressing the lowering button, check whether the lowering valve is powered on. If there is no electricity,KetaiHydraulic straight top lifting platform, clean it as much as possible; If there is power, clear the malfunction of the lowering valve itself or replace the lowering valve. The sliding valve should be kept clean and.
Regularly check the operation of each mechanism for normal operation and noise. If any faults are found, the hydraulic cargo elevator wholesale should be promptly eliminated. Otherwise, it will affect the use of the guide rail hydraulic lifting platform. When refueling, the hydraulic oil should be filtered and filled, and the refueling tools should be reliable and clean. The hydraulic cargo elevator manufacturer should not remove the filter at the fuel tank filler to improve the refueling speed. Refueling personnel should use clean gloves and work clothes to prevent solid and fiber impurities from falling into the oil.