TilburgCustomized hydraulic lifting platformAnalysis and maintenance of deformation problems

Materials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.

Regularly inspect the hydraulic lifting equipment of the upper and lower materials to ensure the safety of the rail type elevator and the safety of the material supply to the rail type lifting platform.

Tilburg.Generally speaking, for situations with large lifting loads and small lifting heights, a lifting mechanism should be selected. For situations with small loads but large lifting heights, a lifting mechanism should be selected. According to the initial structure of the jacking, in order to meet the stability requirements, the size and lifting type of the oil cylinder are increased, and in order to achieve the same effective area as the jacking force, a lifting mechanism should be selected.

Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.

.The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.

An inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage, the surface of the magnetic yoke and armature is skewed,TilburgHydraulic mobile lifting platform, dust or rust is poor, and the device will produce; Buzz&# quo; Noise.

Reason: Manual pump and gear pump have severe oil leakage. Cleaning method: Replace the oil pump sealing ring to clean it. Reason: Gear pump is damaged,TilburgHydraulic lifting table, The oil pumped out has no pressure. Cleaning method: Replace the gear pump to clean the problem. Reason: Lack of hydraulic oil. Cleaning method: Add enough hydraulic oil to clean the problem. Reason: Circuit open. Cleaning method: Check the button and fuse to clean the problem. Reason: Filter blockage. Cleaning method: Replace or clean the problem. Reason: Support valve or electromagnetic directional valve malfunction. There are two situations: the input voltage of the electromagnetic coil is lack of 220V. The solenoid coil is burnt out and the valve core is stuck. Cleaning method: maintenance or replacement can be used to clean the natural descent of the lifting platform. Reason and cleaning method: one-way valve leakage cleaning method: check the check valve in the valve. Assuming there is dirt on the sealing surface of the check valve. Clean the check valve.

The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.

The manufacturer of hydraulic cargo elevators tells you the precautions to be taken when installing hydraulic cargo elevators. Hydraulic cargo elevators work using hydraulic systems and are usually used for the transportation of large goods. Hydraulic cargo elevators are different from traditional shelf elevators. They use a new hydraulic system to reduce the occurrence of faults and utilize their own weight to reduce energy consumption when lowering goods. So, what should be paid attention to when installing hydraulic cargo elevators? The hydraulic cargo elevator manufacturer is here to tell you!

Materials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.

Management Department.Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended,TilburgFixed hydraulic lifting platform, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.

Stable and widely applicable cargo lifting equipment is mainly used for transporting goods between height differences in production lines; Material online and offline; Adjust the height of the workpiece during assembly; High altitude feeder feeding; Lifting of components during assembly of large equipment; Large machine material and cutting; The warehouse loading and unloading site is equipped with forklift and other transportation vehicles for rapid loading and unloading of goods.

Oil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder, it is recommended to replace it with a new one.

The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.

Work courses.When installing, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than 70%. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.

The above are common situations and there are many other reasons based on the actual situation. Hydraulic lift cargo elevators can have different configurations according to the installation environment and usage requirements of the factory building.

The lifting platform is placed on a horizontal support surface, and the concentrated load of MAX load capacity is placed at any position 300mm away from the periphery of the workbench. After lifting 100 times, each load-bearing component must not have deformation or cracks.

Tilburg.The guide rail type elevator has a structure of a straight top oil cylinder. The linear operation of the oil cylinder pulls the transmission chain, driving the lifting of the table to complete the operation. The guide rail type elevator is a popular form of cargo elevator in recent years, with the advantages of higher lifting height, stable operation, it is not practical to change their effective working area A (equivalent to displacement) to adjust the speed. Generally it is easy for hydraulic cargo elevator manufacturers to cause this problem.

For hydraulic cylinders in hydraulic elevators, the speed can only be adjusted by changing the flow rate. For variable displacement motors speed regulation can change both the flow rate and the motor displacement.