Belo HorizonteSmall hydraulic lifting platformWhat is the packaging method

The use of cleaning oil and the brand used in the system

When using hydraulic elevators, the main causes of noise are mechanical mechanism failures, hydraulic system failures, etc. Today, resulting in a decrease in pressure and a natural descent of hydraulic cargo elevators. It is recommended to carefully check whether the oil pipes are intact and undamaged.

When the hydraulic system malfunctions oil leakage, the hydraulic elevator may experience problems with the hydraulic pump, motor, valve, and hydraulic installation after repairing the hydraulic system, which can easily cause vibration and generate significant noise.

.Regularly inspect the hydraulic lifting equipment of the upper and lower materials to ensure the safety of the rail type elevator and the safety of the material supply to the rail type lifting platform.

An inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, dust or rust is poor and the device will produce; Buzz&# quo; Noise.

Protective device: In case of power or oil circuit failure, there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)

When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.

The hydraulic system of the fixed lifting platform of the hydraulic cargo elevator is equipped with anti fall and overload safety protection devices, and operation buttons can be set on each floor and the lifting platform workbench to achieve multi-point operation.

When using hydraulic elevators, the main causes of noise are mechanical mechanism failures, hydraulic system failures, electrical equipment or component failures, etc. Today, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.

quality.The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point,Belo Horizonte5 ton hydraulic lifting platform, the oil seal or straightening rod must be replaced in a timely manner.

Reason: Cleaning method for internal leakage in the oil cylinder: Replace the sealing element of the oil cylinder. The lifting platform does not lower. Reason: The lowering valve is malfunctioning. Cleaning method: When pressing the lowering button, check whether the lowering valve is powered on. If there is no electricity, clean it as much as possible; If there is power, clear the malfunction of the lowering valve itself or replace the lowering valve. The sliding valve should be kept clean and.

Each box, distribution box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.

The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, The hydraulic oil tank has more heat dissipation effect.

Finance Department.When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than 70%. The meshing gap should be appropriate.

The load of goods and the tonnage of goods transported at once also affect the lifting speed. The optimal value for transporting goods on a lifting platform is speed. If it is too heavy,Belo Horizontefork lifter,Belo HorizonteHydraulic guide rail lifting platform, it will affect the speed.

The lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, guide rail and curved arm types. Fixed types include scissor elevators, chain elevators, loading and unloading platforms, and attached electric construction platforms.

Belo Horizonte.The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.

The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far, The hydraulic oil tank has more heat dissipation effect.

Materials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.