Hamburg Ames b
hamburger5 tonThe cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.
The hydraulic oil used in the system has the same brand, and the oil temperature is between 45~80 ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, the system should be drained while the oil is hot. After cleaning, clean the filter and add new oil after using a new filter element.
Hamburg North.Firstly,Hamburg NorthFixed hydraulic lifting platform, rust prevention is necessary. Because the part of the hydraulic cylinder needs to extend out of the cylinder during operation, it will naturally be corroded by oxides and acidic gases. This requires us to apply an appropriate amount of grease to protect it from erosion as a weight component. If we change the oil, we must open the box and use it for a long time to prevent the hydraulic cylinder from being used for a long time. In the operation of hydraulic cylinders, the speed should be appropriate and should not exceed 2m/s to extend the service life of the hydraulic cylinder. In addition, in order to protect the mechanism and safety, it is very important to install buffer devices internally to protect the hydraulic cylinder. The greater the pressure of the protective hydraulic cylinder, the heavier the load, and the greater its pressure. A specialized product manufacturing enterprise that integrates research and development, as well as service. A long-term professional elevator manufacturer
The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.
.A hydraulic elevator is a type of elevator equipment consisting of a walking mechanism, hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, explosion-proof electromagnetic directional valve, throttle valve, and balance valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.
When using an electric mobile scissor lifting platform outdoors, if the wind force exceeds level 5, please stop using it; When the lifting height exceeds 10 meters, the wind ropes at the four corners of the hydraulic lift platform should be tightened and fixed, and the support legs should be reinforced for protection and stability to avoid safety accidents caused by excessive swinging of the electric lifting platform
The optional configurations of a fixed lifting platform include manual hydraulic power, movable flip plates that are easy to overlap with surrounding facilities, rolling or motorized roller tracks, safety contact bars to prevent foot rolling,Hamburg NorthCylinder mounted hydraulic lifting platform, organ type safety protective covers, manual or motorized rotating workbenches, hydraulic overturning workbenches, safety support rods to prevent the lifting platform from falling, stainless steel safety nets, electric or hydraulic lifting platform walking power systems, and universal ball countertops.
The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators, curved arm elevators, car mounted elevators, etc. Their common feature is the hydraulic principle for operation, because the stability of the hydraulic system can bring better user experience and safer operation to the equipment which has been favored by many users.
The above are common situations, and there are many other reasons based on the actual situation. Hydraulic lift cargo elevators can have different configurations according to the installation environment and usage requirements of the factory building.
There are many reasons for unstable workbench descent, such as overload, unstable support, severe eccentric load, hydraulic oil impurities, etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.
Credit guarantee.Introduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, speed up the flow of materials improve the efficiency of loading and unloading operations, and obtain greater economic benefits.
After 10000 hours of operation on the hydraulic lift, and provide safety technical disclosure to the installation personnel for technical design.
The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.
Quality inspection report.Aluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work, and can only provide support for 1-2 people.
Therefore, the oil should be replaced regularly to ensure that the additives are effective. The filter can only absorb a limited amount of dirt particles and other impurities from the oil. Replace the filter according to the recommended cycle to keep the system clean.
. The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve hydraulic control one-way valve, throttle valve, and explosion-proof electromagnetic directional valve. In order to ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve and balance circuit are installed on the return oil circuit to maintain pressure and ensure that the descent speed is not affected by changes in heavy objects. The throttle valve regulates the flow rate and the lifting speed. To ensure safe and reliable braking and prevent accidents, a hydraulic one-way valve, also known as a hydraulic lock, is added to ensure safe self-locking when the hydraulic pipeline bursts. Install an overload sound alarm to distinguish between overload or equipment failure.
Hamburg North.There are many reasons for unstable workbench descent, such as overload, unstable support, severe eccentric load, hydraulic oil impurities, etc. In response to the above reasons, it can be solved by reducing the load, adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.
Hydraulic lift cargo elevators belong to high-altitude work equipment. Small shaking of the scissor type structure is normal, but excessive deviation is a symptom. It is necessary to find the cause and make correct judgments in a timely manner. Generally speaking, operations above 8 meters are generally allowed. Due to its own weight, devices above this height begin to vibrate in different ranges. The vibration range depends on factors such as weight, lifting height, and intensity of high-altitude operations.
When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.