Busgow Freibur
Busgow FreiburI believe many people want to know about the maintenance issues of guide rail hydraulic lifting platforms, as it is related to their service life. During use, frequently check the connection of each part. If loose, tighten it. When the body is under pressure, the tightness of the connecting bolts of the body should be checked (the pressure state that can be used). All connecting shafts should have split pins and hydraulic cargo elevators should be fully opened.
The characteristics of the platform include reliable hydraulic system, large load-bearing capacity and rear hinge support.
Busgow Freiburg.When working on the dam crest, steep slopes, roofs, cliffs towers, suspension bridges, and other dangerous edges, safety nets or protective railings should be installed on the side facing the air. Otherwise, workers must use safety belts. Ice, snow, gravel, and soil on the steep slopes of steep cliffs, boarding bridges, or sidewalks must be regularly cleaned, and a 1-meter high railing must be installed on the outer side. Install an 18 centimeter high side board or soil ridge on the inner side of the railing to prevent falling objects from injuring people.
There are many reasons for unstable workbench descent, such as overload, unstable support, hydraulic oil impurities, etc. In response to the above reasons, it can be solved by reducing the load adjusting the center of gravity of the load, and replacing hydraulic oil wholesale for hydraulic cargo elevators.
.Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.
Road noise can also occur if tires are crushed against objects that are prone to noise. The shaking amplitude of the scissor type lifting platform is proportional to its lifting height. The higher the height, the greater the shaking. When using it at a working height of 10 meters, if possible,Busgow FreiburgMobile hydraulic lifting platform, please use safety protection measures
The manufacturer of hydraulic cargo elevators will tell you about the knowledge of specialized lifting platforms for unloading.
Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.
Due to the formation of a flow closed-loop, the volumetric speed regulation hydraulic elevator has good performance and high load stiffness. The hydraulic system using the volumetric speed regulation scheme has a higher efficiency and greater energy loss compared to the throttling scheme, as its output power is roughly equal to the power required for the elevator to move up. But using an elevator volume speed control system can only reduce the energy consumption during the upward process of the elevator. When the elevator goes down, the oil in the cylinder moves down the throttle valve under pressure, which will cause the temperature of the hydraulic system to rise. Not to mention anything else, just an intelligent alarm is enough to demonstrate the true value of hydraulic elevators.
Reason: Manual pump and gear pump have severe oil leakage. Cleaning method: Replace the oil pump sealing ring to clean it. Reason: Gear pump is damaged, The oil pumped out has no pressure. Cleaning method: Replace the gear pump to clean the problem. Reason: Lack of hydraulic oil. Cleaning method: Add enough hydraulic oil to clean the problem. Reason: Circuit open. Cleaning method: Check the button and fuse to clean the problem. Reason: Filter blockage. Cleaning method: Replace or clean the problem. Reason: Support valve or electromagnetic directional valve malfunction. There are two situations: the input voltage of the electromagnetic coil is lack of 220V. The solenoid coil is burnt out and the valve core is stuck. Cleaning method: maintenance or replacement can be used to clean the natural descent of the lifting platform. Reason and cleaning method: one-way valve leakage cleaning method: check the check valve in the valve. Assuming there is dirt on the sealing surface of the check valve. Clean the check valve.
total cost.The characteristics of the platform include reliable hydraulic system,Busgow FreiburgDouble shear hydraulic lifting platform, simple operation, large load-bearing capacity, and rear hinge support.
There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times Make the damping hole unobstructed, repair or replace the spring, reduce the flow of the remote control port, replace the oil, and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. 5. The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.
Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.
What are the methods for reducing shaking on lifting platforms? Reducing the shaking of the lifting platform can reduce the psychological obstacles of the operators ensure the smooth progress of the operation, and also greatly help improve safety. Warm reminder: safety, do not operate blindly. Lifts are widely used in many places, and their working principles vary. Today, we will analyze the working principles of elevators. The types of elevators are generally divided into the following: fixed elevators, This type of elevator uses hydraulic oil cylinders and pump stations to transmit power, in the form of a scissor fork type. According to customer requirements, the length of the support rod for the scissor fork, the number of layers, the angle of the angle axis, and the expansion and contraction of the oil cylinder complete the lifting operation. Its advantages are large load-bearing capacity, stable lifting, and high safety.
Inspection basis.Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, the oil is supplied by the pressure limiting variable pump, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.
The manufacturer of hydraulic cargo elevators tells you the precautions to be taken when installing hydraulic cargo elevators. Hydraulic cargo elevators work using hydraulic systems and are usually used for the transportation of large goods. Hydraulic cargo elevators are different from traditional shelf elevators. They use a new hydraulic system to reduce the occurrence of faults and utilize their own weight to reduce energy consumption when lowering goods. So, what should be paid attention to when installing hydraulic cargo elevators? The hydraulic cargo elevator manufacturer is here to tell you!
The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within 0.1MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above 400mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.
Busgow Freiburg. Road noise can also occur if tires are crushed against objects that are prone to noise. The shaking amplitude of the scissor type lifting platform is proportional to its lifting height. The higher the height, the greater the shaking. When using it at a working height of 10 meters, if possible, please use safety protection measures
Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.
When disassembling and adjusting the reverse organization of the equipment, and its meshing surface is not less than 70%. The meshing gap should be appropriate.