MazetourVehicl
MazetourHydrauMazetourFixed electric hydraulic lifting platform,
The hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.
When placing materials on the platform, they should be placed in the middle of the platform as much as possible. The weight of the goods should be within the standard load range of the equipment and the volume of the goods should not exceed the platform size of the equipment. Otherwise, materials and lifting platforms may be injured and dangerous accidents may occur. High priced and various specifications of elevator manufacturers provide timely supply, with high cost-effectiveness, and have become the preferred brand for many wire products. Welcome to purchase!
Mazetour.The manufacturer of hydraulic cargo elevators tells you the reason for the instability of hydraulic lifting equipment. Hangzhou hydraulic cargo elevator equipment has always had good stability, mainly used for heavy types of goods. However, during use, Hangzhou hydraulic cargo elevators may inevitably encounter some faults during the lifting process, such as very unstable conditions. What is the reason for the instability of the elevator? How to solve these problems?
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.
.The speed circuit is the circuit that switches the motion speed and speed of the actuator in the hydraulic system of the guide rail hydraulic lifting platform. Mainly including valves, pumps, and actuators. The commonly used speed circuits include speed circuits, high-speed circuits, and speed switching circuits.
When installing, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than 70%. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.
The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators, car mounted elevators, etc. Their common feature is the hydraulic principle for operation because the stability of the hydraulic system can bring better user experience and safer operation to the equipment, which has been favored by many users.
The manufacturer of the hydraulic cargo elevator tells you the reason and cleaning method: Reason: Overload cleaning method: Reduce the load to clean. Reason: The return valve is not closed. Cleaning method: Tighten the return valve to clean. Reason: The one-way valve of the manual pump is stuck and the return valve is malfunctioning. Cleaning method: Unscrew the bolt at the valve port of the oil pump,MazetourHydraulic fixed lifting platform, conduct maintenance, cleaning, and replace the cleaning hydraulic oil to clean.
Below, we will analyze for everyone. According to the market survey and understanding conducted by the editor of hydraulic freight elevator manufacturers, many customers choose hydraulic elevators instead of elevators due to the following reasons: narrow transportation location, which cannot meet the requirements of elevators; Unable to excavate the elevator shaft at the working location; Elevators are expensive and difficult to meet their needs.
For hydraulic cylinders in hydraulic elevators, it is not practical to change their effective working area A (equivalent to displacement) to adjust the speed. Generally, the speed can only be adjusted by changing the flow rate. For variable displacement motors, speed regulation can change both the flow rate and the motor displacement.
install.Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.
Voltage too low: Measure the starter voltage, even if the butter is polished to increase its properties.
Set up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.
Marketing Department.Oil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder, it is recommended to replace it with a new one.
What technical issues are required for the installation of hydraulic freight elevators? The installation of hydraulic freight elevators is actually quite complex. If you do not understand the equipment pictures designed by the elevator manufacturer and the detailed situation of the hydraulic freight elevator designed by the elevator manufacturer, installation errors may occur, leading to equipment failure of the freight elevator! When installing hydraulic freight elevators, it is necessary to accurately calculate the size of the pit. The guide rail hydraulic freight elevator is a freight elevator composed of chains guide rail torque tubes, and other components, mainly driven by the chain to assist in the upward and downward telescopic lifting of the freight elevator. The pulleys at the four corners of the countertop should be fixed on the surrounding guide rails. The entire elevator equipment is installed on the wall and wall mounted installation is chosen to enhance the stability of the freight elevator. Choosing the appropriate wall size also requires careful planning.
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.
Mazetour.An inverter can also generate high noise. When the power supply voltage is lower than 85% of the rated voltage, the short circuit ring of the iron core of the device breaks, the surface of the magnetic yoke and armature is skewed, dust or rust is poor, and the device will produce; Buzz&# quo; Noise.
Voltage too low: Measure the starter voltage, with an allowable fluctuation range of± 10%.
Ensure that there is a suitable power supply at the installation site, and separate maintenance of the distribution box is required. The distribution box should have a leakage switch, and the hydraulic cargo elevator construction site should be equipped with a fire extinguisher to prevent welding operations from causing fires. When selecting a leakage switch