Hong KongScissor fork hydraulic lifting platformWhat are the calculation methods of bearing capacity

After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally, due to overload, insufficient power supply, the starting voltage drop is too large and the price of the cargo elevator is reduced.

Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.

Hong Kong.In winter, when working outdoors at heights below minus 10 degrees Celsius, heating rest areas should be set up near the construction area if necessary. Heating equipment should be managed by dedicated personnel and attention should be paid to fire prevention.

After the pre installation is completed,Hong KongLarge hydraulic lifting platform, the pre installed equipment should be fixed, and the positions of cables, oil pipes, and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws, and the hydraulic cargo elevator after reinforcement has robustness and safety.

.When the hydraulic oil of the equipment is insufficient, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.

A hydraulic elevator is a type of elevator equipment consisting of a walking mechanism,Hong KongHydraulic lifting platform experiment, hydraulic mechanism, electric mechanism, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve, throttle valve, hydraulic control one-way valve, and balance valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.

Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.

After 5000 hours of elevator operation,Hong KongElectric hydraulic lifting platform truck, carry out medium maintenance on the mechanical and electrical systems.

Based on the foundation plan pay attention to alignment, and alignment to ensure the foundation level and various usage requirements. The access road for external construction elevators should be flat and have sufficient space for equipment parking.

Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.

Inspection environment.The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.

The smoothness of the gearbox, gearbox, external meshing gears, and hydraulic oil are all carried out according to the requirements in the smoothness table.

The electromagnetic coil of the electromagnetic directional valve is not firmly fixed, and frequent separation and suction can also produce high noise.

There is noise inside the hydraulic cylinder. When replacing the hydraulic oil, there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible, even when arranging pipelines, it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.

Total quality assurance.Motor not running: Check all components of the motor for damage and check if there are any problems with the circuit and wiring.

Hydraulic cargo elevators are mainly used for the transportation of high-altitude goods such as factory assembly lines, cargo warehouses, parking lots, docks, buildings, logistics, etc. This product can achieve multi-point, interactive interlocking between upper and lower floors, achieving safe use and carrying capacity of 30 tons. The above are the fields in which hydraulic cargo elevators are applied and the characteristics of hydraulic cargo elevators that we want to share with everyone.

The smoothness of the gearbox, external meshing gears, and hydraulic oil are all carried out according to the requirements in the smoothness table.

Hong Kong.The classification of lifting platforms is as follows: they are divided into mobile lifting platforms, automatic lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.

Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract, the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators, to avoid any worries about after-sales service.

Separate: Loading and unloading on different platforms.