Busgow Freibur
Busgow FreiburThe combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.
There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.
Busgow Freiburg.The load of goods and the tonnage of goods transported at once also affect the lifting speed. The optimal value for transporting goods on a lifting platform is speed. If it is too heavy, it will affect the speed. The above is the knowledge about adjusting the lifting speed of hydraulic cargo elevators, hoping to be helpful to everyone. Long term improvement: The manufacturer has a complete range of products, excellent quality, there should be a device to make the workbench emergency descend.
.Therefore, in the hydraulic pipeline assembly line, it will not cause lifting. At this point, you only need to add enough hydraulic oil to run.
Reason: Cleaning method for internal leakage in the oil cylinder: Replace the sealing element of the oil cylinder. The lifting platform does not lower. Reason: The lowering valve is malfunctioning. Cleaning method: When pressing the lowering button, check whether the lowering valve is powered on. If there is no electricity clean it as much as possible; If there is power, clear the malfunction of the lowering valve itself or replace the lowering valve. The sliding valve should be kept clean and.
The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.
The above are common situations, and there are many other reasons based on the actual situation. Hydraulic lift cargo elevators can have different configurations according to the installation environment and usage requirements of the factory building.
The installation personnel should confirm and count the equipment details, confirm that there are no omissions in the shipped equipment details, check if the tools are complete and ensure the smooth progress of the installation process.
How much does it cost?.Considering the oil level in the oil tank, when all hydraulic cylinders in the system are extended, the oil level in the oil tank should not be lower than the Z-low oil level, and when the oil cylinders retract the oil level should not be higher than the Z-high oil level. In fact, most manufacturers have noticed the above issues. The reason for the introduction is that most users can learn more about the equipment itself when using elevators,Busgow FreiburgIndoor hydraulic lifting platform car, in order to facilitate equipment maintenance. Hydraulic cargo elevator manufacturers sincerely hope that you choose a legitimate manufacturer when purchasing elevators, to avoid any worries about after-sales service.
The downward movement of the hydraulic cylinder (i.e. lowering of heavy objects). The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, hydraulic control one-way valve, throttle valve, and explosion-proof electromagnetic directional valve. To ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve is installed on the return oil circuit to balance the circuit and maintain pressure, so that the descent speed does not change due to heavy objects. The throttle valve regulates the flow rate and the ascending and descending speed. To ensure safe and reliable braking and prevent accidents, a hydraulic control one-way valve, also known as a hydraulic lock, is added to ensure safe self-locking in the event of an accidental rupture of the hydraulic pipeline. An overload sound control alarm has been installed to distinguish between overload or equipment failure.
When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height, the larger the mass of the object, the greater the shaking
Reason: The lowering speed valve is out of adjustment. Cleaning method: If the lowering speed valve is adjusted, and if the adjustment is ineffective, replace it with a new valve.
management.When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than 70%. The meshing gap should be appropriate.
It must be abnormal. To solve the problem, the first step is to identify the cause of the problem. Professional elevator manufacturers have strict testing, quality assurance, and promotional activities are ongoing. Welcome to consult
Remember not to overload, overload is the root cause of many faults.
Busgow Freiburg.Introduction to the unloading lifting platform: The unloading lifting platform is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. With it,Busgow FreiburgHydraulic ladder,Busgow FreiburgDouble shear hydraulic lifting platform, forklifts can directly drive from the ground into the interior of car compartments for batch loading and unloading operations. The warehouse unloading platform products use manual hydraulic power and do not require power supply. Only one person needs to operate to achieve safe and fast loading and unloading of goods. It can reduce a lot of labor, improve the efficiency of loading and unloading operations, and obtain greater economic benefits.
When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height, the larger the mass of the object, the greater the shaking
Due to damage to the gear pump of the lifting cargo elevator equipment and no pressure lifting. Replace the gear pump.