Gujiaohydraulic liftIndustry Outlook

After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally, due to overload, insufficient power supply, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.

The guide rail type elevator has a structure of a straight top oil cylinder. The linear operation of the oil cylinder pulls the transmission chain, driving the lifting of the table to complete the operation. The guide rail type elevator is a popular form of cargo elevator in recent years, with the advantages of higher lifting height, stable operation, and simple maintenance compared to the scissor fork type elevator.

Gujiao.Based on experience new steel wire ropes will not suddenly break when used under normal circumstances, unless incorrect operation or safety protection devices fail, as the load borne by the steel wire may exceed its breaking capacity. The damage to the steel wire rope of the cargo elevator is mainly gradually formed during long-term use. After a certain period of repeated bending and friction, the steel wire on the surface of the steel wire rope will experience bending fatigue and wear, and the steel wire on the surface layer will gradually break. At this point, if it cannot be used again, it should be replaced in a timely manner to ensure the safety of the hydraulic platform.

There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, it is easy for hydraulic cargo elevator manufacturers to cause this problem.

.There is noise inside the hydraulic cylinder. When replacing the hydraulic oil, there was air in the hydraulic cylinder due to an operational error. Under high pressure, it is easy to generate cavitation and high-frequency noise. When the rod is bent or replaced with a new seal, the new seal is too tight, which can also produce significant noise. If it is a problem of tight sealing, the noise can be reduced after running in for a period of time. If the rod is bent, it needs to be corrected. In addition, hydraulic pipelines should use hoses as much as possible,GujiaoElectric lifting platform, even when arranging pipelines, it can reduce vibration and noise, and the pipelines should avoid dead bends as much as possible.

Stability: The workbench should evenly withstand 125% of the MAX load capacity and be stable at the MAX elevation.

Electrical equipment or component failures. Hydraulic elevator manufacturers tell you that the main reasons for high noise generated by electric motors are: bent or severely worn motor rotors, or damaged bearings, which cause electric motors to sweep and produce noise; The cooling fan of the electric motor is damaged or not firmly fixed, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.

Next, the hydraulic cargo elevator manufacturer will explain the maintenance of the mechanical equipment of the elevator: the brakes of each organization should be frequently checked and adjusted to ensure the clearance between the brake pads and wheels is sensitive and reliable. On the surface, pay attention to alignment it is necessary to wash it off with gasoline or thinner.

Based on the foundation plan, leveling and alignment to ensure the foundation level and various usage requirements. The access road for external construction elevators should be flat and have sufficient space for equipment parking.

After long-term use of the automatic lifting platform equipment, it is inevitable that some malfunctions will occur. In order not to affect work, it is necessary to promptly solve the difficulties in starting the motor and abnormal sounds. Generally due to overload, insufficient power supply, and a small cross-sectional area of the power supply cable, the starting voltage drop is too large and the price of the cargo elevator is reduced.

Quality improvement.The speed circuit is the circuit that switches the motion speed and speed of the actuator in the hydraulic system of the guide rail hydraulic lifting platform. Mainly including valves, pumps, and actuators. The commonly used speed circuits include speed circuits, high-speed circuits, and speed switching circuits.

Therefore, the wholesale manufacturers of hydraulic elevators remind that there are three main ways to adjust the speed control circuit: throttling speed control circuit: quantitative pump oil supply,GujiaoLogistics hydraulic lifting platform, using flow valves to adjust the flow in and out of the actuator to achieve speed control; In the volume throttling speed control circuit, and the flow rate into the actuator is adjusted by the flow valve to adapt the flow rate of the variable pump to the regulated flow rate of the speed control valve.

When using hydraulic elevators, frequent inspections and maintenance should be carried out, but also enables it to exert greater power during operation. Of course, hydraulic elevators also have their own regular repair times and protection methods: regular protection (carried out per shift).

Aluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work, and can only provide support for 1-2 people.

Standard requirements.Check valve leakage: If the natural wear of the check valve exceeds the specified value after long-term use, it will cause leakage. Disassemble and clean the check valve, and replace it if necessary.

One of the executing components of the hydraulic cargo elevator system is the hydraulic cylinder. The hydraulic cylinder is responsible for linear lifting or retraction. Its characteristics are light weight, high power, simple structure, convenient maintenance, low motion inertia, and convenient remote control. Hydraulic cylinders are widely used in various single acting hydraulic cylinders as an example to analyze the conversion of hydraulic energy into mechanical energy for linear motion.

Materials enter the production line at one end of the factory building, and the production process ends at the other end of the factory building with multiple separate platforms; This can greatly shorten the distance of material flow in the factory building.

Gujiao.The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators, curved arm elevators, car mounted elevators, etc. Their common feature is the hydraulic principle for operation, because the stability of the hydraulic system can bring better user experience and safer operation to the equipment, which has been favored by many users.

After 10000 hours of operation on the hydraulic lift, major repairs will be carried out to the mechanical and electrical systems.

The combined platform is often used in small workshops with small volume of goods. However, because this platform needs to complete two functions at the same time, it inevitably increases the distance of handling tools/vehicles in the workshop.