El PragueFixed electric hydraulic lifting platformThe opening was stable and still weak

Electrical equipment or component failures. Hydraulic elevator manufacturers tell you that the main reasons for high noise generated by electric motors are: bent or severely worn motor rotors, or damaged bearings, which cause electric motors to sweep and produce noise; The cooling fan of the electric motor is damaged or not firmly fixed, resulting in high noise; The electric motor is not firmly fixed and can also cause vibration, producing high noise.

The precautions to consider when selecting a hydraulic lift oil tank include: considering the structure of the oil tank, the partition in the traditional oil tank cannot settle dirt. A vertical partition should be installed along the longitudinal axis of the oil tank, with a space left between one end of the partition and the end plate of the oil tank to connect the gaps on both sides of the partition. The inlet and outlet of the hydraulic pump are arranged on both sides of the partition at the disconnected end, so that the distance Z between the inlet and return oil is far,El PragueDouble fork hydraulic lifting platform, The hydraulic oil tank has more heat dissipation effect.

El Prague.Hydraulic oil is the blood of the cargo elevator. Maintaining the cleanliness of hydraulic oil is an important factor in extending the hydraulic freight elevator. How to maintain the cleanliness of hydraulic elevators?

Voltage too low: Measure the starter voltage, with an allowable fluctuation range of± 10%.

.When using hydraulic elevators, the main causes of noise are mechanical mechanism failures, hydraulic system failures, electrical equipment or component failures, etc. Today, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.

Stable and widely applicable cargo lifting equipment is mainly used for transporting goods between height differences in production lines; Material online and offline; Adjust the height of the workpiece during assembly; High altitude feeder feeding; Lifting of components during assembly of large equipment; Large machine material and cutting; The warehouse loading and unloading site is equipped with forklift and other transportation vehicles for rapid loading and unloading of goods.

Each brush should be kept clean on its surface, and the brush pressure should be adjusted to ensure that its area is not less than 50%.

Hydraulic elevator manufacturers remind us that the basic principle of the hydraulic elevator speed control circuit is that the system often needs to adjust the movement speed of the hydraulic cylinder and hydraulic motor to adapt to the working cycle needs of the main machine. The speed of hydraulic cylinders and hydraulic motors depends on the displacement and input flow rate. It can be seen that changing the flow rate or displacement can affect the speed of the cylinder and motor.

Therefore, the oil should be replaced regularly to ensure that the additives are effective. The filter can only absorb a limited amount of dirt particles and other impurities from the oil. Replace the filter according to the recommended cycle to keep the system clean.

After the pre installation is completed the pre installed equipment should be fixed, and the positions of cables, oil pipes and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws, and the hydraulic cargo elevator after reinforcement has robustness and safety.

total cost.The cylinder head oil seal is too tight or the rod is bent, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.

To consider its capacity, generally mobile equipment takes 2-3 times the high flow rate of pump Z, and fixed equipment takes 3-4 times.

Oil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder, it is recommended to replace it with a new one.

When using hydraulic elevators, the main causes of noise are mechanical mechanism failures,El PragueCustomized hydraulic lifting platform, hydraulic system failures, electrical equipment or component failures, etc. Today, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.

Inspection standard.Regularly check all wires and cables for damage. It is necessary to wrap and replace the damaged parts in a timely manner.

When maintaining hydraulic components, the workbench must be clean. The purpose of the inspection tool.

The installation personnel should have the qualification for installing hydraulic cargo elevators, carefully implement the special construction plan for installation and construction, and provide safety technical disclosure to the installation personnel for technical design.

El Prague.The optional configurations of a fixed lifting platform include manual hydraulic power, movable flip plates that are easy to overlap with surrounding facilities, rolling or motorized roller tracks, organ type safety protective covers, manual or motorized rotating workbenches, hydraulic overturning workbenches safety support rods to prevent the lifting platform from falling, stainless steel safety nets, electric or hydraulic lifting platform walking power systems, and universal ball countertops.

When using hydraulic elevators, the main causes of noise are mechanical mechanism failures, hydraulic system failures, the manufacturer of hydraulic cargo elevators will introduce to you the reasons for the noise generated by hydraulic elevators.

Lines of various safety equipment