SyracuseManual
SyracuseHydrauReason: Manual pump and gear pump have severe oil leakage. Cleaning method: Replace the oil pump sealing ring to clean it. Reason: Gear pump is damaged, The oil pumped out has no pressure. Cleaning method: Replace the gear pump to clean the problem. Reason: Lack of hydraulic oil. Cleaning method: Add enough hydraulic oil to clean the problem. Reason: Circuit open. Cleaning method: Check the button and fuse to clean the problem. Reason: Filter blockage. Cleaning method: Replace or clean the problem. Reason: Support valve or electromagnetic directional valve malfunction. There are two situations: the input voltage of the electromagnetic coil is lack of 220V. The solenoid coil is burnt out and the valve core is stuck. Cleaning method: maintenance or replacement can be used to clean the natural descent of the lifting platform. Reason and cleaning method: one-way valve leakage cleaning method: check the check valve in the valve. Assuming there is dirt on the sealing surface of the check valve. Clean the check valve.
The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds 10 meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.
Syracuse.One of the executing components of the hydraulic cargo elevator system is the hydraulic cylinder. The hydraulic cylinder is responsible for linear lifting or retraction. Its characteristics are light weight, high power, simple structure, convenient maintenance, low motion inertia, and convenient remote control. Hydraulic cylinders are widely used in various single acting hydraulic cylinders as an example to analyze the conversion of hydraulic energy into mechanical energy for linear motion.
I believe many people want to know about the maintenance issues of guide rail hydraulic lifting platforms, as it is related to their service life. During use,SyracuseHydraulic lifting platform truck, frequently check the connection of each part. If loose, tighten it. When the body is under pressure, the tightness of the connecting bolts of the body should be checked (the pressure state that can be used). All connecting shafts should have split pins and hydraulic cargo elevators should be fully opened.
.The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.
Stability: The workbench should evenly withstand 125% of the MAX load capacity and be stable at the MAX elevation.
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.
The main device does not engage. When this fault occurs, check whether the three-phase power supply is normal, whether the internal and external emergency stop button switches, the electric lock switch are turned on, whether the three-phase electrical phase sequence is correct,SyracuseLifting table hydraulic pressure, and whether the relay working indicator light is on.
Today, we will share with you why hydraulic cargo elevators are ideal equipment for transporting goods?
This paper briefly introduces some matters that should be paid attention to in the selection of oil tank for hydraulic elevators. The main functions of the hydraulic oil tank for elevators in the hydraulic systems of hydraulic machinery such as elevators and hydraulic elevators are oil storage, heat dissipation, separation of air contained in oil and elimination of foam.
target.Oil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder, draw on the guide rail lifting platform, prohibit any idle personnel from entering the work area, ensure that the work area is free of clothing, and maintain a clean and tidy workplace.
There is air in front of the pilot valve of the elevator overflow valve noise overflow valve. The damping hole on the main valve core of the overflow valve is blocked by oil dirt, and the pilot valve and valve seat are matched without spring deformation or incorrect installation. The remote control port has excessive oil flow, low or high hydraulic oil viscosity, and resonance occurs with components in the circuit. Troubleshooting: Strengthen sealing, repeatedly adjust the pressure, exhaust and clean the valve body several times Make the damping hole unobstructed, repair or replace the spring, reduce the flow of the remote control port, replace the oil and other components. The pressure setting of other components should not be similar to the pressure setting of the relief valve. 5. The noise of the elevator pipeline is usually caused by excessive dead bends or loose fixed sleeves in the hydraulic pipeline.
The hydraulic lifting platform often checks the connection status of each part, and if there is any looseness it should be tightened. The connection bolts of the machine body should be checked for tightness when the elevator body is under pressure (the compression condition can be formed by rotating the arm). All connecting shafts need to have split pins and need to be fully opened.
Design brand.Solution: Check if the performance of the legs is good, even if the butter is polished to increase its properties.
What are the benefits of hydraulic cargo elevators compared to traditional elevator cargo transportation?
When the hydraulic system malfunctions, the hydraulic elevator may experience problems with the hydraulic pump, motor, valve, and hydraulic installation after repairing the hydraulic system, which can easily cause vibration and generate significant noise.
Syracuse.After the pre installation is completed, the pre installed equipment should be fixed, and the positions of cables, oil pipes,SyracuseFixed hydraulic lifting platform, and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws, and the hydraulic cargo elevator after reinforcement has robustness and safety.
Car mounted lifting platform: The car mounted lifting platform is designed to improve the mobility of the lifting platform by fixing it to a transport vehicle or truck. It receives power from the car engine and achieves the lifting function of the car mounted lifting platform. To adapt to high-altitude operations inside and outside the factory area.
Lifting mechanism: The workbench should be ensured to rise and fall smoothly, and there should be no jumping lifting phenomenon. All moving parts should be flexible when moving, and there should be no jamming devices. The lifting system of the elevator is divided into electric or manual hydraulic systems, and joints.