LeipzigIndoor 
Leipzig6-meterThe hydraulic lifting platform is a manually movable type, and the lifting power of the platform is a two machine or three-phase power supply. It has manual and electric power, and is also equipped with a hand pump for use in case of power outage. This series of platforms have the characteristics of flexible movement, stable lifting, and easy operation, and are mainly used in factories, government agencies, commercial stores, and the construction and decoration industry.
The characteristics of the platform include reliable hydraulic system, simple operation, large load-bearing capacity, and rear hinge support.
Leipzig.On the other hand, under the action of high pressure, the hydraulic system inevitably causes the hydraulic valve to flow back or the sealing components to produce oil. The main reasons for the natural descent of the hydraulic cargo elevator include the following points: replacement of the support valve due to leakage. The lowering valve is damaged or not powered on. Require the lowering valve to be kept clean on a daily basis, and if damaged, replace it with a new hydraulic lowering valve in a timely manner.
Next, the hydraulic cargo elevator manufacturer will explain the maintenance of the mechanical equipment of the elevator: the brakes of each organization should be frequently checked and adjusted to ensure the clearance between the brake pads and wheels is sensitive and reliable. On the surface, there should be no dirt present. If there is dirt, it is necessary to wash it off with gasoline or thinner.
.The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds 10 meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.
Protective device: In case of power or oil circuit failure there should be a safety rope to prevent the workbench from falling out of control. (Allow controlled descent)
The development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.
The elevator is evenly distributed at any position on the guide rail at 150% of the maximum load capacity, and should be stable at the maximum lifting height.
In addition,LeipzigIndoor hydraulic lifting platform car, the convenience of the layout is also a very important issue. For example, in areas with large or high waves, there may be layout issues when using a lifting mechanism. At this point, in order to facilitate the arrangement and prevent the hydraulic cargo elevator cylinder from being eroded by waves, a lifting structure should be selected to determine the installation position of the oil shoulder, during the lifting process of the cylinder, the connection between the two ends of the cylinder and other components must be hinged in the same square. In addition, whether it is the tail lifting ear type, the middle pin shaft type, or the head pin shaft type. The main advantage is that the effective area of the cylinder is large, and the overall installation height is low. The disadvantage is that if the cylinder stroke is large, there may be stability issues with the cylinder, and the cylinder layout may be difficult. The main advantage of the hydraulic cargo elevator lifting mechanism is that it does not have a stable transmission installation frame for height measurement. Therefore, this form can be considered in places with large drops. The sudden deafness oil type on the head can reduce the installation height, but if it is too large, the higher the lifting height, the faster the increase in force,LeipzigHydraulic lifting platform, which is not suitable for the use of the oil cylinder. Therefore when it is too large, the head pin type is not suitable. In order to comprehensively consider the height of the installation bracket and the force on the oil cylinder during the lifting process an intermediate installation method can be considered, and the installation position can be set at an appropriate height according to calculations.
The speed circuit is the circuit that switches the motion speed and speed of the actuator in the hydraulic system of the guide rail hydraulic lifting platform. Mainly including valves, pumps, and actuators. The commonly used speed circuits include speed circuits, high-speed circuits, and speed switching circuits.
Good quality.The downward movement of the hydraulic cylinder (i.e. lowering of heavy objects). The hydraulic oil enters the upper end of the hydraulic cylinder through the explosion-proof electromagnetic directional valve, and the return oil from the lower end of the hydraulic cylinder returns to the oil tank through the balance valve, throttle valve, and explosion-proof electromagnetic directional valve. To ensure a smooth descent of heavy objects and safe and reliable braking, a balance valve is installed on the return oil circuit to balance the circuit and maintain pressure, so that the descent speed does not change due to heavy objects. The throttle valve regulates the flow rate and the ascending and descending speed. To ensure safe and reliable braking and prevent accidents, a hydraulic control one-way valve, also known as a hydraulic lock, is added to ensure safe self-locking in the event of an accidental rupture of the hydraulic pipeline. An overload sound control alarm has been installed to distinguish between overload or equipment failure.
When the hydraulic oil is insufficient, the hydraulic pump will experience suction, causing air to enter the hydraulic oil and producing high noise.
After 10000 hours of operation on the hydraulic lift, major repairs will be carried out to the mechanical and electrical systems.
Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.
Design brand.When installing disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, it will affect the speed.
The guide rail type elevator has a structure of a straight top oil cylinder. The linear operation of the oil cylinder pulls the transmission chain, driving the lifting of the table to complete the operation. The guide rail type elevator is a popular form of cargo elevator in recent years, with the advantages of higher lifting height, stable operation and simple maintenance compared to the scissor fork type elevator.
Leipzig.The above are the working principles of three common elevators, and there are also some forms of elevators that are not common, such as cylinder mounted elevators,LeipzigHydraulic lifting platform, curved arm elevators, car mounted elevators, etc. Their common feature is the hydraulic principle for operation, because the stability of the hydraulic system can bring better user experience and safer operation to the equipment, which has been favored by many users.
The vibration range is proportional to the lifting height. The higher the height, the larger the shaking range, especially for mobile hydraulic cargo elevators. When the working height exceeds 10 meters, the wind ropes at the four corners of the hydraulic cargo elevator should be tightened to strengthen leg protection, increase stability, and reduce shaking.
When the hydraulic lifting platform is working, the load cannot exceed its rated load. When it is raised to a certain height, the larger the mass of the object, the greater the shaking