KarigalinElectA type of elevator equipment consisting of a walking mechanism, hydraulic mechanism electric mechanism,Karigalin8 meter mobile elevator, and support mechanism. The hydraulic oil forms a certain pressure by the vane pump, and enters the lower end of the hydraulic cylinder through an oil filter, explosion-proof electromagnetic directional valve,KarigalinScissor fork high-altitude elevator, throttle valve, hydraulic control one-way valve, and balance valve, causing the hydraulic cylinder to move upwards and lift heavy objects. The return oil at the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic directional valve,Karigalin80 meter elevator, and its rated pressure overflow valve is adjusted. The pressure gauge observes the reading value on the pressure gauge.
Gear pump worn, aged or damaged; The solution is to replace the gear pump. Professional elevator manufacturers have advanced technology, strict testing, more affordable prices and more discounts. Welcome to consult
Karigalin.Improper use of oil: Inadequate maintenance of high-altitude work platform equipment such as mobile elevators can also lead to small fitting gaps of components, making it difficult for oil to form a uniform oil film on the friction surface. Additionally, due to assembly and other reasons, it is difficult to ensure the uniformity of fitting gaps, thereby reducing efficiency and causing early abnormal wear of equipment components; In severe cases, it may cause scratches or bite on the friction surface of precision fitting, leading to the occurrence of abnormal equipment noise.
Dirty normally closed valve; The solution is to remove the normally closed valve and use cleaning agent or cleaning.
.The size of the oil cylinder should be minimized as much as possible while meeting the design requirements. The smaller the size of the oil cylinder, the faster the lifting speed.
Many people believe that the mechanical strength of the elevator itself is relatively high when using it, so during the installation process, there is no
4: Small scale pneumatic or electric rust removal is based on the principle of using air compression to generate friction or electromagnetic effects to polish and remove rust on the surface of spiral elevators. It can be used for precision instrument push rods or for enterprises that require micro operation of spiral elevators.
According to different needs, different power modes can be selected, such as three-phase AC power supply, single-phase AC power supply, DC power supply, and internal combustion power supply. With manual hydraulic equipment, lifting operations can be carried out in places with power outages or no power supply, and components can be added. When the platform length is insufficient, it can be extended to the required direction, and then the operating power can be increased. It is a must-have product of modern large-scale construction and equipment, and a necessity for high-altitude safety and civilized production.
The power system inspection is the core and the key to ensuring its normal operation is to use the hydraulic elevator. The sound of its operation can be used to determine whether it is operating normally and whether there is noise.
The hook of the seat belt should not be hung on unstable or moving objects.
Welcome to inquire.The seat belt needs to be inspected every six months, with a load of 225 kilograms. The test time is five minutes. After the test, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
4: Small scale pneumatic or electric rust removal is based on the principle of using air compression to generate friction or electromagnetic effects to polish and remove rust on the surface of spiral elevators. It can be used for precision instrument push rods or for enterprises that require micro operation of spiral elevators.
What is the solution to the problem of surface rust on the spiral elevator? The deficiency is that sandpaper has a significant loss on the spiral elevator itself.
Work courses.During the use of hydraulic elevators, if not properly operated, there will always be problems. Many customers have reported that hydraulic elevators sometimes cannot be lifted. If the hydraulic lift pump can continue to work, other issues need to be considered. Below, the editor will explain the reasons for the hydraulic lift pump station not being oiled and solve the reasons for the hydraulic lift pump station not being oiled, as well as the solutions for mobile elevators The analysis of the pump station of hydraulic elevators such as guide rail elevators is as follows: the motor power supply is abnormal or reversed; The solution is to correctly connect the motor power supply or adjust the steering mailbox to ensure there is no hydraulic oil or insufficient oil; The solution is to add hydraulic oil.
Check the overall structure for any deformation and damage to important components, especially load-bearing support rods, etc.
The oil filter is severely blocked; The solution is to clean the oil filter or replace the hydraulic oil. Professional elevator manufacturers guarantee quality, service, and quality. Your satisfaction is our pursuit! Welcome to inquire by phone
Karigalin.The oil filter is severely blocked; The solution is to clean the oil filter or replace the hydraulic oil. Professional elevator manufacturers guarantee quality, service, and quality. Your satisfaction is our pursuit! Welcome to inquire by phone
2: Chemical rust removal mainly involves the use of acid to react with the metal components of the screw elevator to remove rust products from the rust surface of the push rod. This type of rust removal is mainly used for large mechanical screw elevators, and attention should be paid to protecting precision devices such as electronic instruments from acid corrosion during use.
Use a heavy crane to lift the cage and accurately position it from above the standard section; Place the two suspension cages on the guide rail frame and slowly place them on the buffer spring. Prepare the drive frames of the two suspension cages and adjust each back wheel and roller to a position with a large gap to facilitate the installation of the drive frame. Install a standard section on the basic part of the elevator using heavy equipment and tighten the connecting bolts. Install two sets of drive frames above each suspension cage using heavy equipment and thread the connecting pins, and install the cage top guardrail.