HanshanSingle What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and elevator are intact, and strictly check whether the dimensions of each part connected to the motor and elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.
Single column aluminum alloy elevator: This series of products is indoor and widely used for high-altitude operations in various industries such as star hotels and large supermarkets. It has lifting balance, easy operation, no pollution, and does not harm the ground during work. It can be used for wall work and exploration work and there are no dead corners during work. The single column aluminum alloy electric elevator, equipped with gantry cross frame accessories, is very suitable for maintenance work in cinemas, auditoriums, etc.
Hanshan.Hydraulic boarding axle; Streamline” The open hinge joint design increases the welding area by more than three times compared to ordinary tubular joints, effectively extending the service life and simplifying maintenance.
Emergency bolts not tightened; The solution is to tighten the emergency valve.
.Remove and disassemble the lowering valve, blow the valve core clean with compressed air, and then reinstall it.
Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.
Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten the inner hexagon. Afterwards, remove the motor shaft key.
Curved arm elevator: a lifting device used for high-altitude operations, which can cross obstacles for high-altitude operations. When the platform is lifted to any position, it can operate while walking, with a compact structure and flexible turning. The width of its site can ensure that the equipment enters narrow passages and crowded working areas. The backup power device can operate the work platform to reset, and is a convenient transportation method that can be towed to any place.
Improper use of oil: Inadequate maintenance of high-altitude work platform equipment such as mobile elevators can also lead to small fitting gaps of components, making it difficult for oil to form a uniform oil film on the friction surface. Additionally, due to assembly and other reasons, it is difficult to ensure the uniformity of fitting gaps, thereby reducing efficiency and causing early abnormal wear of equipment components; In severe cases it may cause scratches or bite on the friction surface of precision fitting, leading to the occurrence of abnormal equipment noise.
The operation of the single column aluminum alloy elevator is relatively convenient. The gantry is easy to assemble across the frame, with labor-saving operation and flexible movement. It can cross obstacles such as fixed seats with a height of up to 1m, and can operate stably on steps. Made of high-strength rectangular steel pipes, with good rigidity and stability. Equipped with universal casters for flexible mobility. The span of the two end brackets can be adjusted, which is suitable for crossing different obstacles. The two end brackets are vertically adjustable and can be used for operations on slopes or steps with a certain slope.
The cheapest.Use a heavy crane to lift the cage and accurately position it from above the standard section; Place the two suspension cages on the guide rail frame and slowly place them on the buffer spring. Prepare the drive frames of the two suspension cages and adjust each back wheel and roller to a position with a large gap to facilitate the installation of the drive frame. Install a standard section on the basic part of the elevator using heavy equipment and tighten the connecting bolts. Install two sets of drive frames above each suspension cage using heavy equipment and thread the connecting pins,HanshanFixed scissor lift, and install the cage top guardrail.
What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC200/200 models, first install the suspension cage before installing the drive plate).
Hydraulic lifting platforms are widely used in factory maintenance, with reliable quality and perfect performance.
Remove and disassemble the lowering valve and decoration of hotels in industrial and mining enterprises, blow the valve core clean with compressed air, and then reinstall it.
Direct material.Aging and deterioration of hydraulic oil; The solution is to replace the hydraulic oil. A specialized product manufacturing enterprise that integrates research and development, as well as service. A long-term professional elevator manufacturer
The correct use of hydraulic elevators can extend their service life and also play an important role. So how should they be used?
What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and elevator are intact, and strictly check whether the dimensions of each part connected to the motor and elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.
Hanshan.The appearance of hydraulic boarding bridges to customers, and the demand for boarding bridges is also increasing. However, there are not many manufacturers of corresponding boarding bridges. Many boarding bridge companies are leather bag companies, and they do not produce them themselves, resulting in high prices. What is important is that they do not have a good understanding of the technology of car booths, and there are often deviations when passing on the technical requirements of direct customers to the manufacturers. Therefore, customers who purchase boarding bridges can directly find professional manufacturers. When choosing a boarding bridge, frequency of work, utilization,HanshanElectric elevator mechanism, rated weight, and other factors of the product, and choose a boarding bridge that is suitable for the requirements of the unit. Conduct market research based on the proposed technical parameters. The first condition for selecting a supplier is to consider the manufacturer of the boarding axle, and then the after-sales service capability. As long as it is a fixed boarding bridge with good product quality excellent performance, it can be chosen at a reasonable price.
Four column aluminum alloy elevator: the whole elevator is made of high-strength aluminum profiles. Due to the high strength of the profiles, the four mast structure is adopted,HanshanFully electric self-propelled elevator, which has excellent stability, flexible operation, large load capacity, large platform area and convenient implementation. Its appearance allows for high lifting capacity in extremely small spaces. Minimize the deflection of the lifting platform.
Install two more standard sections. Check and adjust the verticality of the guide rail frame with a theodolite to ensure that the error in two mutually perpendicular directions meets the requirements of Table 1. The above two parts are about the installation precautions for the elevator. If your work involves operating or installing the elevator, everyone must pay attention to safety.