Rio de Janeiro
Rio de Janeiro2. The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages. The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.
A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function,Rio de JaneiroSimple forklift boarding bridge, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system, and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, improving work reliability.
.Chinese manufacturer of boarding bridges, dedicated to mobile lifting (sh ē Ten series of hydraulic lifting platform products, including platform self-propelled aerial work platform, fixed lifting platform, TTW guide type cargo lift, aluminum alloy (melting point 660 ℃) lifting platform, jacketed lifting platform, car mounted lifting platform, disabled lifting platform, lifting stage, boarding bridge, etc, All properties owned by the company
Activate the up button. When the board reaches a high height, the overlap plate will automatically straighten and be parallel to the panel. At this time, release the up button and the panel will automatically descend until it connects with the carriage. Once confirmed, the operation can begin. After waiting for the homework to be completed, press the up button to drive the vehicle away. Release the button panel and it will automatically descend to its original state, parallel to the cargo platform.
Anti collision block: This device can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф 2. Anchor bolt structure for M20 assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. Platform with& quot; U& quot; Shaped steel as the skeleton with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability. Professional Tideng Axle Factory quality assurance. Discount activities are underway, welcome new and old customers to come for consultation
Fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles to move and load goods in batches inside the truck. With only one person working, fast loading and unloading of goods can be achieved. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.
. Embedded boarding bridge: Embedded boarding bridge, as the name suggests, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device.
Equipment environment, fixed hydraulic boarding bridge itself application requirements, selecting appropriate equipment, can achieve very good application effect. It is a specialized auxiliary equipment for completing the rapid loading and unloading of goods. Horizontal load problems are often encountered in mobile lifting channels and vehicular lifting channels. How do we understand the additional load on fixed hydraulic boarding bridges? The additional load refers to the load that the lifting channel is subjected to under normal operating conditions under non recurring actions.
Sincere service.Product features: Fully hydraulic drive, easy to operate and reliable to operate.
A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other,Rio de Janeiro10 ton fixed boarding bridge, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system, and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.
The rear folding transition plate and forklift traction hook can easily move the boarding bridge. A layer of toothed anti-skid plates or checkered plates is laid on top of the bridge body. The mesh is twisted and hollow, which not only improves the reliability of work, dirt, rainwater, and ice and snow. This equipment is particularly suitable for explosion-proof and flammable places, without generating sparks and no worries. The power can be configured as: manual hand pump power. Electric power. Ensure that the oil cylinder is processed by iron cutting and rolling. Several maintenance and upkeep items for the fixed boarding bridge: each rotating shaft pin should be maintained regularly to reduce wear and enhance flexibility in use; The use of hydraulic oil should follow the specified model, usually 46 # or 68 #, which should be changed every six months and the oil tank should be cleaned; All rotating parts should be regularly cleaned, and the market should clean the dust, oil, iron blocks, etc. on them. During maintenance, do not use water to clean them directly; Regularly inspect all parts for signs of detachment, welding, or looseness, and promptly handle them to avoid breakage during loading; If there is a large area of paint peeling off the ground, it should also not be re applied to avoid rust and corrosion. Hydraulic boarding bridges have become an essential loading and unloading equipment in logistics warehousing. What precautions should be taken when using the equipment? Next, the boarding bridge manufacturer - editor will provide a detailed introduction (xiá ng xì)
All comply with relevant national and industry technical standards, which can be divided into fixed and mobile, guide rail type,Rio de JaneiroPlatform type boarding bridge, folding arm lifting, and curved arm type. Fixed types include scissor fork type lifting cargo elevators, chain elevators, loading and unloading platforms, and attached electric construction platforms. The mobile hydraulic loading bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment, and is an auxiliary equipment for cargo loading and unloading used in conjunction with forklifts. With the help of a mobile loading bridge, forklifts can directly enter the interior of car containers for bulk loading and unloading operations. The car mounted hedge trimmer improves the trimming quality saves labor, improves work efficiency, and has a 40 times higher rate than manual trimming, without any safety hazards; Can form different plant shapes. Used for pruning road greening plants. The green belt trimming machine mainly rotates the head, side, and bottom films to complete the trimming of the top, side, and lawn of the green belt. The machine has a simple appearance, is very convenient to move, is easy to operate, and can adjust the height freely. It can also trim the top, side, and lawn of the green belt at the same time, saving a lot of manpower. The hydraulic cargo elevator must be installed in a closed wellbore environment, and the actual situation of the wellbore determines the specifications and dimensions of the final hydraulic cargo elevator. This includes the width and depth of the shaft, as well as the conditions of the pit and machine room. Hydraulic oil is an important operating medium for fixed hydraulic boarding bridges, which is abstractly compared to the quality of blood hydraulic oil in fixed hydraulic boarding bridges, which indirectly affects the service life of hydraulic lifting channels. Pure and impure hydraulic oil is the key to ensuring the operation of fixed hydraulic boarding bridges. When making a purchase, it is important to carefully reflect, observe the color, and prevent internal environmental purification when storing together.
Marketing Department.Secondly before using the hydraulic boarding axle, it is also necessary to check if there is any oil in the reducer, abnormal noise, and excessive temperature rise in the housing. If there is any oil leakage, it is necessary to check the oil level in the housing, if there is insufficient oil, and add oil. If there is any abnormal noise or rapid temperature rise, repair it in a timely manner
The problem of sealing ring damage is common in almost all hydraulic systems, such as oil cylinders. It may be due to poor quality of the sealing ring itself, insufficient compression of the sealing ring, etc. When the sealing ring is lifted and lowered for a long time, it causes varying degrees of wear and tear on the sealing ring. This is a common cause, leading to gaps in the sealing performance of the sealing ring, resulting in oil leakage. At this time, only the damaged sealing ring needs to be found Just replace it with a new one.
3. Mobile boarding bridges are used in places where there is no loading and unloading platform on site or where mobile loading and unloading of goods is required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Only one person is required to operate without the need for power supply, which can achieve safe and fast loading and unloading of goods.
Rio de Janeiro.Fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles to move and load goods in batches inside the truck. With only one person working, fast loading and unloading of goods can be achieved. It enables enterprises to reduce a large amount of labor improve work efficiency, and obtain greater economic benefits.
A tractable mobile boarding bridge is a type of mobile boarding bridge that can be towed by forklifts, etc. It is developed by combining the technology of flat trailer traction frames. The front section is equipped with heavy-duty universal wheels and detachable traction rods that can be rotated to both sides. When movement is needed, the universal wheels can be rotated to the lower end and a traction rod can be installed, which can easily and conveniently achieve traction movement.
Precautions for safe use of fixed hydraulic boarding bridges When operating the machine, it is necessary to operate it in a safe manner. Unfamiliar personnel should not do so. During the operation, do not stand bystanders around. Be sure to carry the load according to the rated load, and do not overload or deviate. The rated load of the fixed hydraulic boarding bridge specified by the manufacturer is the total weight of the loaded goods and forklifts, not the weight of the goods alone. This is something that customers and friends should know. If there is detachment or deformation of the boarding bridge, please do not use it to avoid serious accidents. The boarding bridge is mainly an auxiliary device for loading and unloading goods, which greatly improves the loading and unloading power (referring to the amount of work done by objects in a unit of time), and is something that logistics companies (Company) cannot do less. If the power of the boarding bridge operation (zuò yì) is to be durable, no problems can appear during the operation. Perhaps the problems can be dealt with in a timely manner. Regarding identifying the cause of the hydraulic system problem of the boarding bridge, It is beneficial for us to use the boarding bridge correctly and provide homework