PreacherBoardi
PreacherSimpleThe fixed hydraulic boarding bridge has three fundamental elements: purification, overheating, and air intake. There is a close internal connection between these three unfavorable factors, and any one of them will result in one or more achievements. Theoretical proof shows that 75% of the reasons for fixed hydraulic boarding bridges are caused by these three factors.
There are generally several forms of axle 1. Embedded boarding bridge, as the name suggests, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device. Its design is usually fully standardized as early as the structural design of buildings.
Preacher.In general there are several reasons for hydraulic cylinder oil leakage: damage to the oil seal ring on the cylinder, etc. The cylinder body of the oil cylinder is damaged. Oil leakage caused by defects such as air holes, sand holes, and shrinkage porosity in the guide sleeve.
Adopting imported integrated modular hydraulic station, with good sealing performance and long service life.
. 2. The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction, the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages. The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.
There are generally several forms of axle 1. Embedded boarding bridge, as the name suggests, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device. Its design is usually fully standardized as early as the structural design of buildings.
The lip plate is connected to the platform using a full length shaft,PreacherCustomized mobile hydraulic boarding bridge, which has high strength and good reliability.
Secondly, before using the hydraulic boarding axle, it is also necessary to check if there is any oil in the reducer, abnormal noise, and excessive temperature rise in the housing. If there is any oil leakage, it is necessary to check the oil level in the housing, and add oil. If there is any abnormal noise or rapid temperature rise, repair it in a timely manner
Function: Convenient unloading strong stability, and low maintenance cost. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic. Loading and unloading platforms, lifting platforms, and unloading platforms: anti slip device: This device is welded from steel plates, which can effectively achieve anti slip function and is safe and reliable. Various legitimate qualifications for boarding bridge factories. Welcome to inquire by phone and sincerely invite cooperation!
Install anti rolling foot skirts on both sides to prevent accidental injury to the toe platform.
Highly recommended.Main technical indicators: Large dynamic load: 6T Large static load: 6T Large width: 2M Large length: 4M Electric hydraulic imported from France assembled mobile hydraulic boarding bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment, and is a cargo auxiliary equipment used in conjunction with forklifts. With the help of this equipment, forklifts can directly enter the interior of the car compartment for batch loading and unloading operations. Only one person is required to operate without the need for power supply, which can achieve safe and fast loading and unloading of goods. It can not only reduce your labor intensity, but also double the efficiency of loading and unloading operations, speed up the flow of materials, and obtain greater economic benefits.
Adopting anti slip patterned steel plates, the platform has good anti slip performance.
The boarding bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles can move and load goods in bulk inside the truck. Only one person needs to work to achieve rapid loading and unloading of goods. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.
There is a support rod that ensures the safety of maintenance personnel entering the interior of the boarding bridge for maintenance.
Project scope.A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition,PreacherMovable hydraulic boarding bridge, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system, and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, improving work reliability.
Fixed loading and unloading bridge: The fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and obtain greater economic benefits.
The following is a brief introduction to the storage of hydraulic oil in fixed hydraulic boarding bridges for a wide range of users: when stopping the hydraulic oil drum and filling it is necessary to achieve three passes and pass when receiving oil; Filtering during barrel rotation: When refueling the equipment, it is too cold to ensure the cleanliness of the bucket mouth, oil injection port, oil barrel, etc., to prevent impurities from entering the oil port and forming hydraulic oil purification.
Preacher.Using a hand operated hydraulic pump as power, the height adjustment of the boarding bridge can be achieved without the need for external power supply.
There is a support rod that ensures the safety of maintenance personnel entering the interior of the boarding bridge for maintenance.
Using a hand operated hydraulic pump as power, the height adjustment of the boarding bridge can be achieved without the need for external power supply.