CampelMobile boarding bridge Fixed boarding bridgeHow to perform preventive maintenance

A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.

All comply with relevant national and industry technical standards, and customer satisfaction has always been our eternal pursuit. The fully automatic lifting platform is a multifunctional heavy loading and unloading mechanical equipment, which can be divided into fixed and mobile, guide rail type, folding arm lifting, and curved arm type. Fixed types include scissor fork type lifting cargo elevators, chain elevators, loading and unloading platforms, and attached electric construction platforms. The mobile hydraulic loading bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment, and is an auxiliary equipment for cargo loading and unloading used in conjunction with forklifts. With the help of a mobile loading bridge, forklifts can directly enter the interior of car containers for bulk loading and unloading operations. The car mounted hedge trimmer improves the trimming quality, improves work efficiency, without any safety hazards; Can form different plant shapes. Used for pruning road greening plants. The green belt trimming machine mainly rotates the head, side, and bottom films to complete the trimming of the top, side, and lawn of the green belt. The machine has a simple appearance, is very convenient to move, is easy to operate and can adjust the height freely. It can also trim the top,CampelSimple boarding bridge, side, and lawn of the green belt at the same time, saving a lot of manpower. The hydraulic cargo elevator must be installed in a closed wellbore environment, and the actual situation of the wellbore determines the specifications and dimensions of the final hydraulic cargo elevator. This includes the width and depth of the shaft, as well as the conditions of the pit and machine room. Hydraulic oil is an important operating medium for fixed hydraulic boarding bridges, which is abstractly compared to the quality of blood hydraulic oil in fixed hydraulic boarding bridges, which indirectly affects the service life of hydraulic lifting channels. Pure and impure hydraulic oil is the key to ensuring the operation of fixed hydraulic boarding bridges. When making a purchase, it is important to carefully reflect, observe the color, smell the scent, and prevent internal environmental purification when storing together.

Campel.At the beginning, it is essential to inspect and maintain the fixed hydraulic boarding bridge before or after use, and pay attention to whether it can be used correctly

A tractable mobile boarding bridge is a type of mobile boarding bridge that can be towed by forklifts, tractors, etc. It is developed by combining the technology of flat trailer traction frames. The front section is equipped with heavy-duty universal wheels and detachable traction rods that can be rotated to both sides. When movement is needed, the universal wheels can be rotated to the lower end and a traction rod can be installed, which can easily and conveniently achieve traction movement.

.Using a hand operated hydraulic pump as power, the height adjustment of the boarding bridge can be achieved without the need for external power supply.

　　3. Mobile boarding bridges are used in places where there is no loading and unloading platform on site or where mobile loading and unloading of goods is required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Only one person is required to operate without the need for power supply, which can achieve safe and fast loading and unloading of goods.

It is understood that the mobile liquid boarding bridge is a specialized auxiliary equipment for cargo loading and unloading used in conjunction with forklifts. The mobile liquid loading and unloading bridge is a specialized auxiliary equipment used in conjunction with forklifts for cargo loading and unloading. By using artificial hydraulic power, the height adjustment of the boarding bridge can be achieved without the need for external power supply. The adjustable length of the cable chain is used to hook the vehicle, ensuring that the boarding bridge always fits tightly with the vehicle even in case of displacement. The mobile wheel is made of solid tires, which do not require inflation. It is sturdy and durable, combined with brake pads to ensure safe operation.

Regarding the year-end maintenance of the boarding bridge, check all hydraulic pipelines and joints to ensure that they are not damaged or loose. All joints must be tightened; Discard all hydraulic oil and replace it with new oil to avoid continuing to use old oil. Otherwise, the moving components in the system will accelerate wear and tear. Remove and disassemble the lowering valve, blow out the plunger with compressed air, and then reinstall it. To use a fixed hydraulic boarding bridge, it is necessary to have a basic understanding of its basic knowledge. Below, Jinan Zhongding Elevator will analyze it for everyone: To operate a fixed hydraulic boarding bridge, first open the rear door of the truck, fix it on both sides of the carriage and then reverse the truck to the front of the platform until it meets the anti-collision rubber blocks on both sides of the fixed hydraulic boarding bridge. Then, brake the truck. Turn on the power switch on the electric control box, and the professional boarding bridge factory has stable, safe, reliable, and can achieve maintenance free performance. The technical level has reached the domestic level and the international advanced level of similar products

It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф 2. Anchor bolt structure for M20 assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. The platform is based on&quo; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.

　　3. Mobile boarding bridges are used in places where there is no loading and unloading platform on site or where mobile loading and unloading of goods is required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Only one person is required to operate without the need for power supply, which can achieve safe and fast loading and unloading of goods.

resources.Install anti rolling foot skirts on both sides to prevent accidental injury to the toe platform.

Regarding the year-end maintenance of the boarding bridge, check all hydraulic pipelines and joints to ensure that they are not damaged or loose. All joints must be tightened; Discard all hydraulic oil and replace it with new oil to avoid continuing to use old oil. Otherwise, the moving components in the system will accelerate wear and tear. Remove and disassemble the lowering valve, blow out the plunger with compressed air, and then reinstall it. To use a fixed hydraulic boarding bridge, it is necessary to have a basic understanding of its basic knowledge. Below, Jinan Zhongding Elevator will analyze it for everyone: To operate a fixed hydraulic boarding bridge, first open the rear door of the truck, fix it on both sides of the carriage, and then reverse the truck to the front of the platform until it meets the anti-collision rubber blocks on both sides of the fixed hydraulic boarding bridge. Then, brake the truck. Turn on the power switch on the electric control box, and the professional boarding bridge factory has stable, safe, reliable, and can achieve maintenance free performance. The technical level has reached the domestic level and the international advanced level of similar products

There are generally several forms of axle 1. Embedded boarding bridge, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device. Its design is usually fully standardized as early as the structural design of buildings.

Set up a new oil warehouse testing system: Before entering the hydraulic lifting channel, hydraulic oil should be stopped from sampling and testing. Unqualified oil should be stopped from entering the warehouse, and the quality of the warehouse should be strictly controlled. A special hydraulic oil protection system should be set up: the oil should be stored and stored according to the brand when entering the warehouse, and disorderly storage should be prohibited. It should be stored in a dry and ventilated place in the open air for daily rain and rain, and should not be close to the fire fixed hydraulic boarding bridge. Label storage system should be established for mixed types, It is necessary to fill out labels in a timely manner and conduct regular sampling and testing: In order to ensure the quality of the oil products leaving the warehouse, it is necessary to conduct seven regular inspections of the hydraulic oil inventory. Any unqualified oil products found after testing should be disposed of in a timely manner and containers should not be used for regular cleaning. Containers containing hydraulic oil should be cleaned regularly, and special personnel should be assigned to handle some of the more precise parts in the fixed hydraulic boarding bridge. Although mechanical hydraulic drive is labor-saving and convenient, and its preventive maintenance is not very clear. The fixed boarding bridge is for convenient repair and maintenance. It will not affect the normal operation of the equipment.

Latest consultation.Function: Convenient unloading, strong stability, and low maintenance cost. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic. Loading and unloading platforms, lifting platforms, and unloading platforms: anti slip device: This device is welded from steel plates, which can effectively achieve anti slip function and is safe and reliable.

At the beginning, it is essential to inspect and maintain the fixed hydraulic boarding bridge before or after use, and pay attention to whether it can be used correctly

Used as a bridging device between forklifts and trucks, facilitating loading and unloading of goods. Large dynamic load: 6T, large static load: 6T, large width: 2M, large length: 4M. There are many classifications, generally divided into mobile boarding bridges and fixed boarding bridges. General: Solid tires with a length of 11M and a width of 1M. The Ramp loading and unloading platform is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and safely turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to safely and quickly enter and exit transportation vehicles for loading and unloading operations.

Campel.Chinese manufacturer of boarding bridges, dedicated to mobile lifting (sh ē Ten series of hydraulic lifting platform products, including platform, self-propelled aerial work platform, fixed lifting platform,CampelBoarding bridge type boarding bridge, TTW guide type cargo lift, aluminum alloy (melting point 660 ℃) lifting platform, folding arm lifting platform, car mounted lifting platform, disabled lifting platform, lifting stage, boarding bridge, etc, All properties owned by the company

All comply with relevant national and industry technical standards, and customer satisfaction has always been our eternal pursuit. The fully automatic lifting platform is a multifunctional heavy loading and unloading mechanical equipment, guide rail type, folding arm lifting, and curved arm type. Fixed types include scissor fork type lifting cargo elevators, chain elevators, loading and unloading platforms, and attached electric construction platforms. The mobile hydraulic loading bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment and is an auxiliary equipment for cargo loading and unloading used in conjunction with forklifts. With the help of a mobile loading bridge, forklifts can directly enter the interior of car containers for bulk loading and unloading operations. The car mounted hedge trimmer improves the trimming quality, saves labor improves work efficiency, without any safety hazards; Can form different plant shapes. Used for pruning road greening plants. The green belt trimming machine mainly rotates the head, side, and bottom films to complete the trimming of the top, side, and lawn of the green belt. The machine has a simple appearance, is very convenient to move,CampelBoarding Bridge Mobile Boarding Bridge, is easy to operate, and can adjust the height freely. It can also trim the top, side, and lawn of the green belt at the same time saving a lot of manpower. The hydraulic cargo elevator must be installed in a closed wellbore environment, and the actual situation of the wellbore determines the specifications and dimensions of the final hydraulic cargo elevator. This includes the width and depth of the shaft, as well as the conditions of the pit and machine room. Hydraulic oil is an important operating medium for fixed hydraulic boarding bridges, which is abstractly compared to the quality of blood hydraulic oil in fixed hydraulic boarding bridges, which indirectly affects the service life of hydraulic lifting channels. Pure and impure hydraulic oil is the key to ensuring the operation of fixed hydraulic boarding bridges. When making a purchase it is important to carefully reflect, smell the scent, and prevent internal environmental purification when storing together.

Using a hand operated hydraulic pump as power, the height adjustment of the boarding bridge can be achieved without the need for external power supply.