Darbus Small b
Darbus 10 ton A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.
A one line boarding bridge suitable for special heavy-duty vehicles in special situations. If all the wheels of any multi axle vehicle are rigidly suspended on the frame of the trailer, it cannot be guaranteed that all the wheels will be suspended from the ground at the same time when driving on harsh roads, resulting in accidents such as wheel suspension and serious vehicle body accidents. It seriously affects the driving smoothness and handling stability of the vehicle. The use of a one line, two axle boarding bridge can ensure that all wheels have good contact with the road surface when driving on harsh road conditions, thereby reducing accidents such as vehicle body and improving vehicle driving smoothness and handling stability. The self steering boarding bridge is designed based on the principle of adjusting and stabilizing steering according to different loads. The hydraulic boarding axle beam and the steering pin fluctuation pressure bearing are connected together. When the vehicle is traveling in a straight line, the mass of the vehicle itself causes the upper and lower wavy pressure plates to mesh closely with each other, thereby maintaining the straight running state of the wheels. Whenever a semi trailer turns, the wavy tooth surface of the pressure bearing is misaligned, raising the axle beam and causing the wheels to automatically turn. The frictional resistance between the two pressure blocks also needs to undergo corresponding changes depending on the load on the boarding bridge. In addition, according to different loads, the steering angle limiter can automatically increase the steering angle. At the same time, the steering tie rod also causes the instantaneous center of rotation of two wheels to coincide. The anti slip device of the boarding bridge is welded with steel plates, which can effectively achieve anti slip function, safe and reliable. Anti collision blocks can effectively protect buildings and boarding bridges from damage. It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф The anchor bolt mounting bridge for M20 assembly is composed of a mechanical system, a hydraulic system, and an electrical system. The platform and chassis form a mechanical system. Elevating the platform to; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.
Darbus .The guide sleeve has air holes, sand holes shrinkage, and other conditions. Generally, there is a problem with the casting, which is the quality of the oil cylinder itself. At this time, it is necessary to find a manufacturer to replace the new boarding bridge. Normally, and frequent inspections should be conducted in these two areas. Hydraulic loading and unloading bridge is a specialized auxiliary equipment that maintains rapid loading and unloading of goods during the application process. The height adjustment function of the equipment makes the bridge in the middle of the truck guide sufficient to be built. Lifting platforms, trucks, and hydraulic loading and unloading bridges are commonly used cargo loading and unloading equipment.
The boarding bridge is convenient for unloading has strong stability, and low maintenance costs. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic, the boarding bridge is composed of mechanical systems, hydraulic systems, and electrical systems. Fully hydraulic drive, easy to operate and reliable to operate. The lip plate is connected to the platform using a full length shaft,Darbus Fixed boarding axle hydraulic pressure, which has high strength and good reliability. The use of imported seals ensures excellent sealing performance of the hydraulic system. Adopting imported integrated modular hydraulic station, with good sealing performance and long service life. Monthly maintenance of the landing bridge of the lifting platform. The landing bridge, like other handling tools, also needs regular maintenance in the future. Regular maintenance will appropriately extend the use of the landing bridge. Once the hydraulic oil becomes dark, sticky or has sand and gravel and other foreign matters it should be replaced in a timely manner; Each part should be filled with some oil separately, which can extend the service life of the bearing.
.The adjustable length of the cable chain can easily hook the truck, ensuring that the boarding bridge and truck always fit tightly.
The fixed hydraulic loading and unloading bridge is a specialized auxiliary equipment for fast loading and unloading of goods. Its height adjustment function allows a bridge to be built between the truck and the cargo platform in the warehouse. Forklifts and other transport vehicles can directly enter the truck for batch loading and unloading of goods, and only one person can work to achieve fast loading and unloading of goods. Boarding bridges reduces a large amount of labor for enterprises, improves work efficiency, and achieves greater economic benefits.
The boarding bridge is convenient for unloading, has strong stability, and low maintenance costs. Suitable for various vehicles on loading and unloading sites and places with relatively busy traffic, the boarding bridge is composed of mechanical systems, hydraulic systems, and electrical systems. Fully hydraulic drive, easy to operate and reliable to operate. The lip plate is connected to the platform using a full length shaft, which has high strength and good reliability. The use of imported seals ensures excellent sealing performance of the hydraulic system. Adopting imported integrated modular hydraulic station, with good sealing performance and long service life. Monthly maintenance of the landing bridge of the lifting platform. The landing bridge, like other handling tools,Darbus dock levelers , also needs regular maintenance in the future. Regular maintenance will appropriately extend the use of the landing bridge. Once the hydraulic oil becomes dark, sticky or has sand and gravel and other foreign matters, it should be replaced in a timely manner; Each part should be filled with some oil separately, which can extend the service life of the bearing.
High strength& quot; U& quot; The design of the shaped beam can ensure its high load and long-term operation without deformation.
It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф 2. Anchor bolt structure for M20 assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system, and electrical system. The platform and chassis form a mechanical system. The platform is based on&quo; U” Shaped steel as the skeleton with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of 10 kilometers/hour when the forklift is fully loaded without bending, improving work reliability.
Using a hand operated hydraulic pump as power, the height adjustment of the boarding bridge can be achieved without the need for external power supply.
Service first.Main technical indicators: Large dynamic load: 6T Large static load: 6T Large width: 2M Large length: 4M Electric hydraulic imported from France assembled mobile hydraulic boarding bridge is widely used in cargo platforms and mobile loading and unloading places without loading and unloading equipment and is a cargo auxiliary equipment used in conjunction with forklifts. With the help of this equipment, forklifts can directly enter the interior of the car compartment for batch loading and unloading operations. Only one person is required to operate without the need for power supply, which can achieve safe and fast loading and unloading of goods. It can not only reduce your labor intensity, but also double the efficiency of loading and unloading operations, speed up the flow of materials, and obtain greater economic benefits.
The use of imported seals ensures excellent sealing performance of the hydraulic system.
The rear folding transition plate and forklift traction hook can easily move the boarding bridge. A layer of toothed anti-skid plates or checkered plates is laid on top of the bridge body. The mesh is twisted and hollow, which not only improves the reliability of work, but also prevents the accumulation of grease, rainwater, with manual hydraulic power,Darbus Boarding bridge type boarding bridge, without generating sparks and no worries. The power can be configured as: manual hand pump power. Electric power. Ensure that the oil cylinder is processed by iron cutting and rolling. Several maintenance and upkeep items for the fixed boarding bridge: each rotating shaft pin should be maintained regularly to reduce wear and enhance flexibility in use; The use of hydraulic oil should follow the specified model, usually 46 # or 68 # which should be changed every six months and the oil tank should be cleaned; All rotating parts should be regularly cleaned, and the market should clean the dust, sand, oil, etc. on them. During maintenance, do not use water to clean them directly; Regularly inspect all parts for signs of detachment, welding, or looseness, and promptly handle them to avoid breakage during loading; If there is a large area of paint peeling off the ground, it should also not be re applied to avoid rust and corrosion. Hydraulic boarding bridges have become an essential loading and unloading equipment in logistics warehousing. What precautions should be taken when using the equipment? Next, the boarding bridge manufacturer - editor will provide a detailed introduction (xiá ng xì)
A tractable mobile boarding bridge is a type of mobile boarding bridge that can be towed by forklifts, tractors, etc. It is developed by combining the technology of flat trailer traction frames. The front section is equipped with heavy-duty universal wheels and detachable traction rods that can be rotated to both sides. When movement is needed, the universal wheels can be rotated to the lower end and a traction rod can be installed, overheating, and air intake. There is a close internal connection between these three unfavorable factors, and any one of them will result in one or more achievements. Theoretical proof shows that 75% of the reasons for fixed hydraulic boarding bridges are caused by these three factors.
At the beginning, it is essential to inspect and maintain the fixed hydraulic boarding bridge before or after use, and pay attention to whether it can be used correctly
Before delivery for use, it is necessary for us to conduct static and dynamic experiments on the fixed hydraulic boarding bridge equipment to achieve different application effects. Based on the equipment environment of the elevator and the application requirements of the fixed hydraulic boarding bridge itself, selecting appropriate equipment can achieve very good application effects. It is a specialized auxiliary equipment for completing the rapid loading and unloading of goods. The fixed hydraulic boarding bridge is used indoors or outdoors, and whether it is a fixed lifting channel or a mobile lifting channel. The fixed hydraulic boarding bridge helps to ensure the safe operation of our equipment. The countertop adopts a specially designed diamond grid plate with reliable strength, which can ensure long-term use without deformation. Its diamond shaped mesh structure fully ensures excellent anti slip performance, making the forklift have better climbing and maneuverability. Even in rainy and snowy weather, normal use can still be guaranteed.
Darbus .The equipped brake pads can effectively prevent the shifting of the boarding bridge during truck loading and unloading.
Product features: Fully hydraulic drive, easy to operate and reliable to operate.
Used as a bridging device between forklifts and trucks, facilitating loading and unloading of goods. Large dynamic load: 6T, large static load: 6T, large length: 4M. There are many classifications, generally divided into mobile boarding bridges and fixed boarding bridges. General: Solid tires with a length of 11M and a width of 1M. The Ramp loading and unloading platform is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and safely turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to safely and quickly enter and exit transportation vehicles for loading and unloading operations.