TurkuFactory e
Turku4-meter sTurkuElectric scissor lift,
Hydraulic pump station: domestic lifting platform dedicated pump station, Italian imported pump station with external protective devices: organ m type,TurkuConvenient mast elevator, mesh type, which has a certain impact on work efficiency and needs to be removed. So what is the solution to the surface rust of the spiral elevator?
Turku.Hydraulic boarding axle; Streamline” The open hinge joint design increases the welding area by more than three times compared to ordinary tubular joints elevators are widely used and are involved in many industries. The spiral elevator is no exception and has a very good effect. But sometimes the surface of the spiral elevator will rust, effectively extending the service life and simplifying maintenance.
The product has a sturdy structure a large load-bearing capacity, smooth lifting, simple and convenient installation and maintenance, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will share with you some common knowledge about daily maintenance of outdoor elevators: When personnel enter the interior of the lifting platform for maintenance,Turku10 meter automatic elevator, they must hang the elevator to prevent sudden lowering of the platform and causing casualties.
.High altitude work requires the use of tool bags, and heavier and larger high-altitude work tools should be hung on stable components and cannot be placed randomly to avoid the occurrence of high-altitude falling accidents.
Curved arm elevator: a lifting device used for high-altitude operations, it can operate while walking, with a compact structure and flexible turning. The width of its site can ensure that the equipment enters narrow passages and crowded working areas. The backup power device can operate the work platform to reset, and is a convenient transportation method that can be towed to any place.
What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, a pad iron must be used below the screws to increase the force surface between the nuts and the floor to reduce the impact of the nuts on the floor; Insert steel plate shims of different thicknesses between the chassis and the foundation stone at the anchor bolts to adjust the verticality of the guide rail frame; Install three standard sections and measure the verticality of the guide rail frame using a theodolite to ensure the verticality of each main pipe in both directions. After adjusting the verticality of the guide rail frame, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC200/200 models, first install the suspension cage before installing the drive plate).
Curved arm elevator: a lifting device used for high-altitude operations, which can cross obstacles for high-altitude operations. When the platform is lifted to any position, it can operate while walking, with a compact structure and flexible turning. The width of its site can ensure that the equipment enters narrow passages and crowded working areas. The backup power device can operate the work platform to reset, and is a convenient transportation method that can be towed to any place.
Now that you understand how to use a hydraulic lift, it provides us with a safe working environment for our operators, and improves the efficiency and quality of the lowering work.
Install two more standard sections. Check and adjust the verticality of the guide rail frame with a theodolite to ensure that the error in two mutually perpendicular directions meets the requirements of Table 1. The above two parts are about the installation precautions for the elevator. If your work involves operating or installing the elevator, everyone must pay attention to safety.
manufacturer.During the use of hydraulic elevators, if not properly operated, there will always be problems. Many customers have reported that hydraulic elevators sometimes cannot be lifted. If the hydraulic lift pump can continue to work, other issues need to be considered. Below, the editor will explain the reasons for the hydraulic lift pump station not being oiled and solve the reasons for the hydraulic lift pump station not being oiled, as well as the solutions for mobile elevators The analysis of the pump station of hydraulic elevators such as guide rail elevators is as follows: the motor power supply is abnormal or reversed; The solution is to correctly connect the motor power supply or adjust the steering mailbox to ensure there is no hydraulic oil or insufficient oil; The solution is to add hydraulic oil.
2: Chemical rust removal mainly involves the use of acid to react with the metal components of the screw elevator to remove rust products from the rust surface of the push rod. This type of rust removal is mainly used for large mechanical screw elevators, and attention should be paid to protecting precision devices such as electronic instruments from acid corrosion during use.
Hydraulic lifting platforms are widely used in factory maintenance, municipal construction, and decoration of hotels in industrial and mining enterprises, with reliable quality and perfect performance.
High altitude operations involving single person work such as high-altitude cleaning. Products, professional elevator manufacturers ensure safe trading
How much does it cost?.Walking: assisted self-propelled, two wheel traction, self driving, and car modification.
Before use, carefully check the grounding wire, safety devices, buffer springs etc. Ensure a safe usage environment.
Many people believe that the mechanical strength of the elevator itself is relatively high when using it, so during the installation process, there is no
Turku.Introduction to Fixed Boarding Bridge Loading and unloading Mobile Boarding Bridge is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.
Dirty normally closed valve; The solution is to remove the normally closed valve and use cleaning agent or cleaning.
Loose or leaking connection between the oil suction pipe and the gear pump; The solution is to tighten the suction pipe.