HuvdopElevator
HuvdopConstrucThe oil filter is severely blocked; The solution is to clean the oil filter or replace the hydraulic oil. Professional elevator manufacturers guarantee quality, service, and quality. Your satisfaction is our pursuit! Welcome to inquire by phone
Walking: assisted self-propelled,HuvdopCar mounted scissor lift, two wheel traction, self driving, and car modification.
Huvdop.At this point, if the high-altitude work platform is overloaded, it may cause damage to the components and cause some mechanical failures.
Preparation before folding and installation of the elevator. Carefully prepare a special construction plan for installation and provide safety technical disclosure to the installation personnel.
.Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten the inner hexagon. Afterwards, remove the motor shaft key.
Outdoor elevators and factory cargo elevators are heavy lifting mechanical equipment. Outdoor elevators are used for transporting goods between floors of buildings and are specialized hydraulic cargo elevator products. They are mainly used for transporting goods up and down between various working floors; Vertical garage and car lift between garage floors. The hydraulic system of the product is equipped with anti fall and overload protection devices, and operation buttons can be set on each floor and lifting platform workbench to achieve multi-point operation.
Install two more standard sections. Check and adjust the verticality of the guide rail frame with a theodolite to ensure that the error in two mutually perpendicular directions meets the requirements of Table 1. The above two parts are about the installation precautions for the elevator. If your work involves operating or installing the elevator, everyone must pay attention to safety.
What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC200/200 models, first install the suspension cage before installing the drive plate).
The double column aluminum alloy lifting platform is designed with beautiful and generous appearance, and is made of high-strength aluminum alloy material. It has a large load-bearing capacity, usually ranging from 6-14 meters in height, and can carry a load of 150-300 kilograms. Large countertop design allows for one to two people to work simultaneously.
Single column aluminum alloy elevator with easily recognizable operation panel,HuvdopCustomized lifting platform by manufacturer, multiple mechanical, electrical, and hydraulic safety protection and advanced integrated hydraulic electricity
Good quality.Welcome from home, able to easily deliver goods to high-rise buildings. Among them, hydraulic elevators are more popular among people, and people can choose the one that suits them according to their actual situation. However, during normal work, it is important to pay attention to the lifting speed of hydraulic elevators and avoid making mistakes. So what factors will affect the lifting speed of hydraulic elevators?
The power unit adjustment, whether it is a scissor type lifting platform or a guide rail type lifting cargo elevator, is composed of the power unit and the oil cylinder. The power unit has four outlets during production, which can be adjusted to increase or decrease the hydraulic oil flow rate of the oil cylinder. We can adjust the motor speed or the electro-hydraulic proportional valve to adjust the hydraulic oil flow rate; What factors will affect the lifting speed of hydraulic elevators? The longer the hydraulic oil pipe the longer the lifting time. Therefore, during installation, the length of the oil pipe should be minimized as much as possible within the allowable range of the design; On the basis of adjusting the power unit, and corresponding adjustments can be made while ensuring that the equipment meets normal demand and safety.
What kind of function can be achieved by installing the elevator? Before installation, confirm whether the motor and elevator are intact, and strictly check whether the dimensions of each part connected to the motor and elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.
Three column aluminum alloy elevator: Three sets of masts support the synchronous lifting of the working platform, and the support structure is the same as that of a single masted platform, with super large load capacity and work stability. The overall lifting guardrail device has good strength and greatly reduces the height of the entire machine during transportation. It is very convenient for loading and unloading, and can be assembled or disassembled in one lift.
Service first.The elevator has a strong load-bearing capacity and is suitable for two people (who can carry a certain amount of weight tools and materials) to climb high at the same time; Various non-standard products can also be customized according to different environments to meet different needs.
The concept of hydraulic boarding bridge is the power system of the boarding bridge. The large oil cylinder lifts the entire equipment inclined plate. When it is raised to a large height,HuvdopBuilding elevators, the small oil cylinder begins to operate, extending the hinge tongue plate. All equipment plates are made of high-quality high height patterned steel plates and profiles, which are effectively welded and have a long service life.
What are the installation precautions for elevators? The folding fence and cage of the elevator should be cleaned of the foundation surface, and the foundation bolts should be installed properly. If the construction elevator is installed on the floor, tighten the four foundation bolts; Adjust the verticality of the fence door frame as above and tighten the remaining anchor bolts; Install the buffer spring; Connect the other half of the fence to the front half with bolts; Adjust the verticality and tighten the anchor bolts as above, and release the brake on the motor inside the suspension cage. (For SC200/200 models, first install the suspension cage before installing the drive plate).
Huvdop.Preparation before folding and installation of the elevator. Carefully prepare a special construction plan for installation and provide safety technical disclosure to the installation personnel.
Aging and deterioration of hydraulic oil; The solution is to replace the hydraulic oil. A specialized product manufacturing enterprise that integrates research and development, as well as service. A long-term professional elevator manufacturer
Reset the brake; Installation and maintenance section. The maintenance section is generally installed in the fourth section. Long term promotion of downgrading manufacturers, 20 year old brand, with price advantages and guaranteed quality!