Danube new townGuide rail type cargo elevatorOperation mode and characteristics

Before connecting the motor to the elevator, the elevator manufacturer should first make the motor shaft keyway perpendicular to the tightening bolt. To ensure uniform stress, but do not tighten them. Then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. After that tighten the tightening bolts. All tightening bolts shall be fixed with a torque wrench according to the indicated fixed torque data, and the use of elevators and lifting platforms shall be checked

Does the cleanliness of the hydraulic station have relevant rules and requirements?

Danube new town.Avoid,Danube new townCargo elevator, especially during storage. Store in a cool and dry place, and avoid rainy and snowy weather during work.

Hydraulic pump station: domestic lifting platform dedicated pump station, Italian imported pump station with external protective devices: organ m type, mesh type, and iron plate sealed type.

.Walking: assisted self-propelled, two wheel traction, self driving, and car modification.

Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten with the hexagon socket. After that, Italian imported pump station with external protective devices: organ m type, mesh type, and iron plate sealed type.

Manual hydraulic platform classification: Manual hydraulic lifting platform vehicles can be divided into manual hydraulic handling platform vehicles, manual hydraulic stacking platform vehicles, and manual hydraulic shear type platform vehicles.

Test the goods elevator every day to see if it can operate normally.

Marketing Department.Many people believe that the mechanical strength of the elevator itself is relatively high when using the elevator, so the installation method specified in the manual is not strictly followed during the installation process. However, use it is necessary to pay attention to the installation precautions corresponding to the working environment and not be careless. Correct installation, and maintenance of the elevator are important steps to ensure the normal operation of mechanical equipment. Therefore, when installing the elevator, please be sure to carefully assemble and use it in strict accordance with the following installation and use related matters.

Before installing the elevator, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of each part connecting the motor and the elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.

Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten with the hexagon socket. After that, remove the motor shaft key.

Safety performance: The lifting structure is made of high-strength manganese steel rectangular tubes,Danube new town5 ton lifting cargo elevator, with a scissors type mechanical mechanism,Danube new townSecond floor cargo elevator, easy to maintain, strong stability, and high bearing capacity. The lifting height is about 10 meters, and the load capacity is about 10 tons.

Direct material.Low cost: Compared to the scissor type mobile lifting platform the cost is much lower. Therefore, when purchasing a lifting platform, it is necessary to consider the use range, frequency of work, load and other factors of the lifting platform to select a lifting platform suitable for the work requirements.

How to install and use the bearings of the elevator During the process of installing the bearing device of the elevator, we cannot always ensure that the bearing device has the correct orientation, which inevitably leads to some devices not in place or bearing misalignment. Once these problems occur in the device, the clearance between the bearings becomes too small, and then the inner and outer rings of the bearings cannot be located at the same rotation center. Therefore, when installing bearings, it is necessary to use specialized tools, and in the future, it is also necessary to use a detector to test the bearing device, so as to ensure the success of the bearing device.

The load of this series of products is divided into 0.1 to 0.8 tons, and can also be customized according to user requirements, with a load of up to 10 tons.

Danube new town.Test the goods elevator every day to see if it can operate normally.

The brake operators of each mechanism on the equipment should regularly check and adjust the clearance of the brake shoe and brake wheel, ensuring flexibility and reliability. Long term improvement of the elevator factory, a 20 year old brand with competitive prices and guaranteed quality!

Guide rail elevator (also known as cargo elevator) is a non scissor fork type hydraulic lifting platform, mainly used in industrial buildings, restaurants, restaurants, warehouses, docks, workshops, and other places where vertical cargo handling is required between two or more floors. The low height is particularly suitable for sites that are not suitable for digging pits on site. What issues should we pay attention to in these places where elevators are used?