BalmazuvarosEl
BalmazuvarosBuwith a scissors type mechanical mechanism, easy to maintain, strong stability,BalmazuvarosFreight elevator lifting, and high bearing capacity. The lifting height is about 10 meters, and the load capacity is about 10 tons.
The load of this series of products is divided into 0.1 to 0.8 tons, and can also be customized according to user requirements, with a load of up to 10 tons.
Balmazuvaros.The one-way valve is damaged. The one-way valve is designed to prevent oil return. If there is a problem, there will be some backflow, so it can be replaced at this time.
Unscrew the screws on the dustproof hole on the outer side of the elevator flange, adjust the PCS system ring to align its side hole with the dustproof hole, and tighten with the hexagon socket. After that, remove the motor shaft key.
.Precautions for using guide rail type elevators: Overloading and transporting flammable and explosive products are strictly prohibited.
The motor winding is short-circuited. When a short circuit fault occurs in the motor winding, causing the winding to overheat or even burn out.
Corrosion prevention measures for the body of aerial work vehicles Attention to small scratches The paint surface of aerial work vehicles often corrodes. In addition to common collisions, scratches, there can also be a paint peeling point that can cause a small rust over time. Because most of these scars are small and easy to ignore. Therefore, regularly inspect the engine compartment lid and surrounding areas and once found, go to a professional beauty shop for processing in a timely manner.
Before installing the elevator, confirm whether the motor and the elevator are intact, and strictly check whether the dimensions of each part connecting the motor and the elevator match. Here are the dimensions and fit tolerances of the positioning boss, input shaft, and elevator groove of the motor.
As we all know now, elevators and lifting platforms have been widely used in recent years to solve the problems we encounter in daily life. Because working at heights is a high-risk profession that requires the assistance of auxiliary tools to complete certain tasks, the use of elevators is undoubtedly emerging in the domestic machinery market and has been vigorously developed.
To ensure excellent power supply at the installation site, install a separate distribution box. When using the distribution box, the electrical leakage switch must meet the requirements for construction elevators. If the installed construction elevator is variable frequency, the selection of the leakage switch should be compatible with the frequency converter.
Test results.Incorrect connection of the elevator motor When a coil coil group, or one phase winding group is connected inversely, it can cause a serious imbalance in the three-phase current and cause the winding to overheat.
Is the water cooling and air cooling of the hydraulic station the same?
Prepare the foundation according to the foundation plan, pay attention to alignment, leveling,Balmazuvaros13 meter guide rail type cargo elevator,BalmazuvarosWorkshop lifting cargo elevator, and alignment, and ensure the level of the foundation and various usage requirements.
In addition, it is strictly prohibited to use a hammer during installation to prevent excessive axial or radial force from damaging the bearings or gears. Be sure to tighten the mounting bolts before tightening the tension bolts. Before installation, clean the anti rust oil on the motor input shaft, positioning boss, and elevator connection parts with gasoline or zinc sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.
recommend.Corrosion prevention measures for the body of aerial work vehicles Attention to small scratches The paint surface of aerial work vehicles often corrodes. In addition to common collisions, scratches, and small rocks on the drive tire, there can also be a paint peeling point that can cause a small rust over time. Because most of these scars are small and easy to ignore. Therefore, regularly inspect the engine compartment lid and surrounding areas, and once found, go to a professional beauty shop for processing in a timely manner.
What is the solution to the problem of rust on the surface of the spiral elevator? Sandpaper has a large loss on the spiral elevator itself. Specializing in products, renewable resources business, including: elevator factory
The water cooling of hydraulic stations is generally tubular water cooling, and the type selection is based on the heat load to calculate the heat exchange area while the air-cooled elevator is conducted using an air cooler, the type selection calculation is performed when the flow can be satisfied. Therefore and the heat exchange capacity is calculated based on the heat load. Then, the two types of cooling are different, and there are significant differences. Long-term lifting and lowering of cargo elevator factory
Balmazuvaros.Different. (Specific bearing capacity and lifting height can be designed and customized according to user requirements)
Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand cranking outriggers, and pull-out outriggers.
The water cooling of hydraulic stations is generally tubular water cooling, and the type selection is based on the heat load to calculate the heat exchange area, while the air-cooled elevator is conducted using an air cooler, and the heat exchange capacity is calculated based on the heat load. Then, the type selection calculation is performed when the flow can be satisfied. Therefore, the two types of cooling are different, and there are significant differences. Long-term lifting and lowering of cargo elevator factory