St. Louis Hydr
St. Louis ManuThe boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.
When using the elevator, we should listen for any abnormal noise. If there is any abnormal noise, we should immediately stop using it to avoid serious damage to the elevator.
St. Louis .It can be seen that the hydraulic lifting platform needs to carefully inspect the hydraulic and electrical systems before use, so as to facilitate its use.
After working for 10000 hours, it should be stopped immediately, and after troubleshooting, it should continue to operate. The motor bearings should be in good condition.
Drain all the hydraulic oil in the oil tank, open the oil tank, take out the oil suction filter, clean it, and return it to the oil tank. Install it in its original position. Fill the fuel tank with new oil.
We
The electric lifting platform needs to work under load according to the regulations on the nameplate during use, but overloading is strictly prohibited during use. Especially in emergency situations, it can only briefly overload by 10%.
For customers to use and operate the lifting platform for a long time, the editor briefly introduces how to maintain and repair the lifting platform: First of all, normal maintenance is mainly focused on prevention, especially if any damage or malfunction is detected and corrected or repaired in a timely manner. Careful inspection and maintenance at this time can save costs and avoid larger problems, resulting in costly repairs.
production costs.Copyright © 2006-2022 Yan-wei.Net.All Rights Reserved.
Once again weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, scissors, wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.
Of course, when choosing a lift it is also necessary to consider its production. If a manufacturer has a large production capacity, it indicates its strong strength, when making a purchase, it is important to consider the factory building and process of its production, all of which are very important.
When conducting high-altitude operations on dangerous edges such as roofs, suspension bridges, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air, or safety belts or ropes should be used.
reform.Introduction to Fixed Boarding Bridge Loading and unloading Mobile Boarding Bridge is a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.
Of course,St. Louis Small hydraulic lifting platform, the hydraulic lifting platform uses a dual protection structure which can make the work relatively safer. When lifting, an appropriate working surface can be selected, so that the lifting platform will be safer during operation. The process of operating the hydraulic lifting platform should be standardized, so that maintenance and debugging can be carried out before leaving the factory. At the same time, it can also ensure that all technical indicators can meet the design requirements, but it is necessary to connect the ground wire during use. Of course, the hydraulic electrical system does not need to be adjusted in this situation.
Regularly check the connection of each part, and forklifts and other vehicles can move and load goods in batches inside the truck. Only one person can work to achieve rapid loading and unloading of goods. It enables enterprises to reduce a large amount of labor, improve work efficiency,St. Louis Hydraulic loading and unloading platform, and obtain greater economic benefits.
Secondly, the lifting platform is driven by electrical energy and lifted by the hydraulic system. During operation,St. Louis Mobile hydraulic loading platform, it is necessary to avoid irregular operations. To ensure the normal and orderly operation of the lifting platform and achieve the ideal unloading level, timely inspection of various functions is essential.
The product has a sturdy structure, a large load-bearing capacity, smooth lifting, simple and convenient installation and maintenance, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will share with you some common knowledge about daily maintenance of outdoor elevators: When personnel enter the interior of the lifting platform for maintenance, they must hang the elevator to prevent sudden lowering of the platform and causing casualties.