GraHydraulic lifting platform 100tThe buying group gradually expands

The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.

Troubleshooting: When the elevator power light is turned on, press the up button, the motor rotates,GraHydraulic loading and unloading platform, but the lifting platform does not rise. This may be due to the reversal of the motor after the three-phase power supply is connected, just change the two phase wires of the heavy machine.

Gra.For lifting platforms without manned protection, it is strictly prohibited to carry people during use. At the same time, attention should be paid during use to prevent damage to hands, feet, and clothing.

Head signature:

.If there are problems inside the elevator and electrical professionals are present, any components of the hydraulic system should be disassembled and repaired in a completely depressurized condition.

Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated.

When conducting high-altitude operations on dangerous edges such as roofs, slopes, or cliffs, guardrails or safety nets should be installed on the side facing the air,GraElectric hydraulic pressure of lifting platform, and forklifts and other vehicles can move and load goods in batches inside the truck. Only one person can work to achieve rapid loading and unloading of goods. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.

The characteristics of hydraulic lifting platforms are obvious such as their relatively light overall weight and good maneuverability, allowing even a single person to operate, attention should also be paid to the structure of the hydraulic lifting platform to ensure its compact structure so its lifting and lowering are relatively stable during use. Of course, so as to ensure its size during transportation. Only in this way can you enter the car of a general elevator,GraHydraulic lift truck platform, and then you can smoothly open the door. Of course, some small and narrow channels are also possible, so we need to pay attention to this point.

The reduction gearbox, gearbox, external gear teeth, and other parts, as well as the hydraulic oil, are all carried out according to the requirements in the table.

Development Curriculum.The hook of the seat belt should not be hung on unstable or moving objects.

When using the elevator, we should listen for any abnormal noise. If there is any abnormal noise, we should immediately stop using it to avoid serious damage to the elevator.

Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, but does not have a price advantage. Therefore, a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.

After 5000 hours of operation of the elevator repair the mechanical and electrical systems.

quality standard.Hydraulic lifting platform is a non scissor type hydraulic lifting platform and is also a widely used vertical transportation equipment for goods, among which the commonly used is the guide rail hydraulic lifting platform. Mainly driven by electric motors and oil pumps, heavy chains are driven by oil cylinders to drive the lifting and lowering of hydraulic lifting platforms. It is also widely used for vertical transportation of goods between high-rise buildings. So, what are the advantages and characteristics of guide rail hydraulic lifting platforms?

It can be seen that the hydraulic lifting platform needs to carefully inspect the hydraulic and electrical systems before use, so as to facilitate its use.

Shafts must have split pins and be sufficient.

Gra.Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, but does not have a price advantage. Therefore, a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.

Fixed loading and unloading bridge: The fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles can move and load goods in batches inside the truck. Only one person can work to achieve rapid loading and unloading of goods. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.

Secondly, for the replacement of hydraulic oil on the lifting platform, it is recommended to replace it every three months. If the frequency of use is not high, it can be replaced once a year. The hydraulic oil must be clean, and after changing the hydraulic oil, it must be automatically lifted and lowered 2 to 3 times to ensure that the air in the oil cylinder is completely discharged, maintain sufficient space, and ensure that the lifting platform can be lifted to the rated lifting height.