ZhuozhouElectric hydraulic elevator platformHow to operate during construction

The loading and unloading mobile boarding bridge has become a very common structural form in modern logistics sites. It is the point and endpoint of the enterprise logistics chain, and a loading and unloading operation platform for enterprises to quickly and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height difference or gap between the transportation vehicles and the loading and unloading platform due to the height of the carriage. Causing the forklift to be unable to enter and exit the transportation vehicle for direct loading and unloading of goods. Use the boarding bridge to provide reliable connections. Enable forklift trucks to quickly enter and exit transportation vehicles for loading and unloading operations.

Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, scissors wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.

Zhuozhou.When using a hydraulic lifting platform, there are many details that cannot be ignored. It mainly uses an external power supply, so when operating, personnel need to master its operating knowledge which is the basic content. At the same time, it is also necessary to master corresponding emergency response plans. When processing, it is also necessary to check the corresponding route,ZhuozhouShear difference hydraulic lifting platform, which is the basic content. So in addition, what preparations do hydraulic elevators need to master during use?

Update Log

.Regularly check the connection of each part, and tighten it if there is any looseness

Remove and disassemble the lowering valve,ZhuozhouFactory hydraulic lifting platform,ZhuozhouFour wheel hydraulic lifting platform, blow the valve core clean with compressed air, and then reinstall it.

Firstly, an obvious advantage is its high safety performance. The guide rail hydraulic lifting platform adopts heavy-duty chain transmission, safety devices to prevent overloading, multiple limit switch protection, door and power outage protection, leakage protection, and multi-layer building interaction. Therefore, the safety factor of the guide rail hydraulic lifting platform is still very high, much higher than that of ordinary platforms.

Regularly check all wires and cables for damage, and promptly wrap and replace the damaged parts.

To understand the operation of the mechanism, the main focus is on whether it is normal and whether there is noise during use. When faults are found, timely troubleshooting is necessary to ensure the normal operation and use of the machine. During installation, it is necessary to disassemble or adjust the rotating mechanism. In this case, it is necessary to ensure that the rotating mechanism can be parallel to the centerline of the reducer and the centerline of the gear, and of course, the meshing clearance should also be appropriate. If this is not appropriate, then the machinery cannot operate normally.

Check the rollers, intermediate shafts, and bearings; Oil cylinder pin and bearing; Equality and wear of the hinge shaft and bearings of the boom; Add oil to the above components for maintenance of outdoor elevators and factory elevators. Extend the service life of bearings.

Quality documents.Later when there is a major malfunction of the lifting platform, it should be repaired by professional personnel as soon as possible. After the malfunction occurs, it should not be used again to avoid accidents, personnel and property losses.

If the elevator malfunctions, non electrical professionals are not allowed to disassemble and assemble electrical appliances at will to prevent accidental connection or electric shock!

Secondly, the maintenance of the guide rail type hydraulic lifting platform is also very simple, using oil cylinders and chain transmission, with very few moving components, so the maintenance workload is not very high. Moreover, this type of lifting cargo elevator has a very compact structure and uses fewer bearings, resulting in a longer service life.

If there are problems inside the elevator and electrical professionals are present, any components of the hydraulic system should be disassembled and repaired in a completely depressurized condition.

For more, please check.The boarding bridge can be divided into two forms: a mobile boarding bridge and a fixed boarding bridge. A brief introduction to the application scope of a fixed boarding bridge and the use of a mobile boarding bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods are required. If there is no loading and unloading platform at the logistics site as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. Fast loading and unloading of goods can be achieved with only one person operating and without the need for power supply.

In this situation, it is necessary to regularly check all wires and cables used to ensure that there is no damage. When there is wrapping or damage, the parts should be replaced in a timely manner. I believe many people have encountered overheating in electric motors. In this case, it is necessary to stop the motor in a timely manner, and then troubleshoot the problem before continuing to use it. This way, its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.

Zhuozhou.When working at heights exceeding 1.5 meters, safety nets or safety belts must be used.

When using the elevator, the legs must be opened first. If the legs are not lifted, it is strictly prohibited to lift them.

Everyone knows that construction elevators are used during the construction process because they have stability, are sturdy and reliable during use, and are widely used in the field of high-rise buildings due to their small size and other advantages.