WatfordPlatform hydraulic lift truckManufacturing process

Hydraulic lifting platform is a non scissor type hydraulic lifting platform and is also a widely used vertical transportation equipment for goods, among which the commonly used is the guide rail hydraulic lifting platform. Mainly driven by electric motors and oil pumps, heavy chains are driven by oil cylinders to drive the lifting and lowering of hydraulic lifting platforms. It is also widely used for vertical transportation of goods between high-rise buildings. So, what are the advantages and characteristics of guide rail hydraulic lifting platforms?

The product has a sturdy structure, a large load-bearing capacity, smooth lifting, simple and convenient installation and maintenance, making it an ideal and economical cargo conveying equipment for replacing elevators between low floors. The editor will share with you some common knowledge about daily maintenance of outdoor elevators: When personnel enter the interior of the lifting platform for maintenance, they must hang the elevator to prevent sudden lowering of the platform and causing casualties.

Watford.It can be seen that the hydraulic lifting platform needs to carefully inspect the hydraulic and electrical systems before use, so as to facilitate its use.

Leading spaces in blank lines Full width: Font size: Replace: Replace

.Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective whether there is a lack of hydraulic oil,WatfordHydraulic fixed lifting platform, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame, and oil cylinder once a week to avoid dust and debris affecting normal operation.

Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast, making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, but does not have a price advantage. Therefore, a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.

The elevator has undergone strict testing before leaving the factory. If the pressure regulating valve is adjusted arbitrarily by non manufacturers, it may cause abnormal system operation. Non professionals should not adjust the pressure regulating valve arbitrarily!

The use of highlights is cost-effective. When aluminum alloy elevators were in the market, their price was also a significant highlight. Because manufacturers make reasonable and moderate pricing decisions in their daily processes, it is well known that manufacturers generally consider manufacturing costs when pricing. and

Especially when its pipes are in use, they are quite boring and can roll, so in this case, they need to be blocked or tied tightly. This is relatively appropriate, so it is necessary to pay attention to these details during use. Especially for unmanned protective lifting platforms, it is not allowed to carry people during use, it is equipped with railings or anti crack valves, which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.

Regularly check the connection of each part, and tighten it if there is any looseness

Lets see.We

Regardless of the type of lifting platform used, people are more concerned about the stability during use. Because the stability not only affects the actual use effect, but also has varying degrees of impact on the safety during use, it is necessary to pay appropriate attention. The same applies when using fixed loading and unloading platforms, but many times the stability of this type of platform can be trusted. The reason for saying this is because the manufacturer has taken this issue into account during production and manufacturing, and the following aspects are taken to avoid this situation.

Maintenance time regulations for hydraulic elevators: After 1500 hours of daily maintenance of the elevator, repair the mechanical and electrical systems.

Using Help

property right.When working at heights exceeding 1.5 meters, safety nets or safety belts must be used.

Especially when its pipes are in use, they are quite boring and can roll, so in this case they need to be blocked or tied tightly. This is relatively appropriate, so it is necessary to pay attention to these details during use. Especially for unmanned protective lifting platforms, it is not allowed to carry people during use, and it is strictly prohibited to carry people. If the electric lifting platform carries people during use, which are mainly used to prevent the oil pipe from breaking or causing its workbench to fail during use and then descend.

Update Log

Watford.Safety protection components, in order to ensure safety production, it is essential to install a lifting platform for proper protection. The main protective accessories include safety belts, guardrails, protective covers, platform stairs, etc.

Once again, weekly inspections should be conducted to check whether the connecting screws at various parts of the lifting platform are tightened, whether the sealing rings are damaged or ineffective, whether there is a lack of hydraulic oil, and whether the oil cylinder is leaking. It is necessary to clean the lifting frame,WatfordPlatform Hydraulic, scissors, wiring, and oil cylinder once a week to avoid dust and debris affecting normal operation.

Due to the fact that the power unit of the hydraulic lifting platform requires an oil source, its structure is relatively complex, and it also has a certain degree of pollution and impact on the environment. The speed of the moving device is relatively fast making it difficult to meet the design requirements for speed. The structure of the electric rod is very simple, occupies small space, but does not have a price advantage. Therefore a power source is used as the lifting power source, The DC motor is directly transmitted to other mechanical devices through a reducer for deceleration.