BellasRed copper barThe golden period of building a brand

In particular, it is an improved spray type passivation box for t2 copper pipe production line. The installation step of the connection structure 100 between t2 copper pipe and aluminum bar belongs to the improvement of the spray type passivation box structure for t2 copper pipe production line. The passivation solution spray box is set above the side of the passivation solution box, the passivation solution spray box with downward sloping bottom is connected with the inlet of the passivation solution box by the outlet set on the box wall at the bottom of the inclined bottom, the inlet of the passivation solution box is located on the box wall above the passivation solution box, the upper side of the passivation solution box is installed with a passivation pump, and the inlet pipe of the passivation pump is connected with the passivation solution box, The outlet pipe of the passivation pump is connected with the upper port of the passivation liquid spray box. With reasonable structure and convenient operation it is convenient for operators to add passivation liquid to the passivation box, clean colloidal crystals at the bottom of the passivation box, avoid equipment blockage, with a diameter of about 35mm. The material is: the melting temperature of wire 221 is about 0905 ℃. Its chemical composition is FB10 The composition is 2331% H3BO3 and 6071% KBF The joint form of brazed copper pipe is mostly plug-in. Before cleaning the brazed copper pipe before welding, it shall be fixed by tack welding. The number, size and height of tack welds shall be symmetrically and evenly distributed along the circumference from top to bottom, left to right, and the tack welds shall be melted into the whole weld during brazing. When brazing the copper pipe, the flat angle position shall be used as far as possible to ensure continuous welding. Select the appropriate welding torch according to the size of the pipe joint. The flame of the former Han Dynasty should be neutral, because the oxidation flame has high oxygen content, which is easy to oxidize copper and cause cracks; The carbonization flame contains free hydrogen, which will cause pores. When heating pipes before welding, the flame shall be perpendicular to the heating surface, the pipe joints shall be heated evenly, and the base metal shall be heated as quickly as possible to avoid excessive temperature and heating time of the through pipe joints. During the brazing of degreased copper tube, the brazing seam and filler metal shall be under the protection of flame. In addition, it shall be noted that the brazing seam shall be naturally cooled after welding, and the weldment shall not be moved before the brazing seam has solidified. After natural cooling after welding, hot water or wet cloth shall be used to wipe the brazing seam and remove welding slag to improve corrosion resistance and reliability of post welding inspection.

Bellas.The market opened today. Although the performance of Zitong Pai futures was modest, the overall market has stopped. The market mentality has not changed much since the weekend. The price is stable, but some specifications are subject to negotiation, and the negotiation range is about 10-20 yuan. The overall rhythm of the market is stable and cold. In the middle of winter, the overall market in Northeast China has entered the traditional off-season, and the overall market has ended with little improvement. All companies are selling goods. The inventory level in Shenyang is very low due to the inventory clearing, and all construction sites have been closed. In addition to the transportation pressure brought by the low temperature, the market was bleak.

Plastic coated copper pipe is a kind of non-metallic material pipe with light weight, high strength and corrosion resistance. The plastic coated copper pipe is made of glass fiber with resin base weight, which is wound on the rotating hollow floor step by step according to the processing technology regulations, and the stone sand is laid on the ground evenly for a long distance in the middle of the chemical fiber as the intermediate weathering layer. The price quotations of plastic coated copper pipes with different thicknesses are also different. Here, we will explain the factors that determine the thickness of the plastic coated copper pipe design scheme. Appearance and specification of mpp cable duct 1 Color: generally orange red, other colors can be implemented according to the contract of both parties. 2 Appearance quality: The inner and outer walls of the pipe fittings shall be smooth, clean and even, and shall be free of steam bubbles, cracks, cracks, molting, and obvious marks, dents, residues, dissolved discoloration lines and uneven colors. The inner holes of the pipe shall be laser cut and leveled and vertical to the pipe centerline. The inner holes shall be smooth and free of burrs. Specification: The length of pipe fittings is generally 6000 or 9000mm, which can also be negotiated by both parties. The specification error shall conform to dl/t801; The bending degree of the hose shall not exceed 1% of the nominal pressure. Some key points in the process of embedding plastic coated copper pipe: the embedding process of plastic coated copper pipe is very worthy of great attention. Although the actual operation in the process of embedding is relatively simple, it is seriously affected by external forces. Relevant countermeasures must be taken if the road surface is seriously uneven In other words, and fine sand and dirt should also be prohibited from seeping into the pipe during the burial process, so as to diligently maintain its compliance with the regulations during the burial process. The process of embedding the plastic coated copper pipe involves the problem of marking. In fact, it is only necessary to find matching marks for immediate maintenance. Number of layers of cloth stacking: all layers are made strictly according to the design scheme without additional construction, which increases the cost. 2 Resin: high temperature resistance, not easy to deform under stress. Plastic coated copper pipes are generally assembled from high-quality SMC water tank plates. Its characteristic is that it can select food grade stainless steel resin. Therefore, in view of the good water body, clean up the natural environment and zero pollution, the commodity development trend has certain characteristics such as high compressive strength, light weight, corrosion resistance, beautiful and generous appearance design scheme, long service life, and more convenient management methods in maintenance. Cloth quality: the specification of cloth surface is the same, pure platinum cloth is thick, and it is thick with blended cloth or pure old coarse cloth. The thickness of fiberglass filament winding: our products are high-tech support points of fiberglass anti-corrosion ring, which ensures the bearing pressure of the products. In addition, if you must select the thickened type, you can yze the vertical cross type difficult winding when winding the winding machine, until the thickness and compressive strength of the thickened type are basically achieved.

.What problems should we pay attention to in each production. It is a key process to weld copper pipe with correct process. Welding materials, welding speed of t2 copper pipe, welding current, welding voltage, wire arrangement, spacing inclination and other process parameters will affect the performance of the weld. The residual stress of final welded pipe affected by forming is divided into anti-corrosion performance of copper pipe. Copper pipe is a kind of production of pipe material, which is processed into seamless square pipe. The physical properties of copper tubes are slightly weaker than those of hot-rolled steel tubes. The copper tube adopts a two-step push tube expanding machine, which integrates cone die tube expansion, data medium frequency induction heating and hydraulic press. With effective processing technology, low energy consumption, less infrastructure construction, good products, wide application fields of raw materials and products, and what are the production batches suitable for copper tube testing. When purchasing copper tubes, but this is effective for a few customers, but it is time-consuming and labor-intensive for many customers, it is recommended to conduct a large number of inspections within a small scope of procurement and then the following is how to conduct inspections. The dimension tolerance of the cleanliness and wall thickness of the inner cavity of the copper tube is strict. However, in the whole process of electric welding due to the role of the molten metal material of the air conditioning copper pipe, the thickness of the pipe at the welding point will be uneven, and the inside and outside of the welding will be uneven. This will cause energy consumption of the conveyor. At this time, the internal welding ground must be used for leveling. Next, many materials are also used in the life of red copper pipes. Be as judgmental as possible when buying. In fact, there are many things to pay attention to when purchasing copper tubes. Want to keep high when buying. What should we pay attention to when buying copper tubes next. The daily use and market are calculated according to the weight, so you should decide how much to use before buying.

Generally speaking, professional t2 copper tube manufacturers will adopt an integrated molding process to improve the yield and reduce production costs while packaging products with superior performance. As long as the above t2 copper tube quality identification method is used, it is basically guaranteed to purchase t2 copper tubes with reliable quality. If long-term and large-scale procurement is required, it is recommended to go to the manufacturer for field inspection to determine the basic performance and quality of t2 copper tubes before large-scale mold procurement. The position of grid accessories plays a very important role in the whole construction process. The products with high cost performance and good performance certainly have a great assistance effect for the implementation of the project. In addition, it is necessary to improve technology and consider the performance requirements of today's construction projects. In fact, Only by maintaining the overall reasonable layout of the grid products can we ensure the long-term performance advantages. Many technologies are required in the whole process of production and manufacturing of space truss accessories. The production and manufacturing staff should ensure the performance advantages when carrying out production and manufacturing of products. The production and processing of space truss should improve its corrosion resistance, compression resistance and strength to ensure that qualified products are produced by the original factory.

Generally speaking, professional t2 copper tube manufacturers will adopt an integrated molding process to improve the yield and reduce production costs while packaging products with superior performance. As long as the above t2 copper tube quality identification method is used, it is basically guaranteed to purchase t2 copper tubes with reliable quality. If long-term and large-scale procurement is required, it is recommended to go to the manufacturer for field inspection to determine the basic performance and quality of t2 copper tubes before large-scale mold procurement. The position of grid accessories plays a very important role in the whole construction process. The products with high cost performance and good performance certainly have a great assistance effect for the implementation of the project. In addition, it is also beneficial to the application of the middle and later stage of the forming project. There are high regulations for the performance of the grid. How about the corrosion resistance of the grid accessories? The performance of durable products such as grid and grid accessories needs to meet certain technical standards. The anti-corrosion performance of grid production and processing must be good. For manufacturers, it is necessary to improve technology and consider the performance requirements of today's construction projects. In fact, Only by maintaining the overall reasonable layout of the grid products can we ensure the long-term performance advantages. Many technologies are required in the whole process of production and manufacturing of space truss accessories. The production and manufacturing staff should ensure the performance advantages when carrying out production and manufacturing of products. The production and processing of space truss should improve its corrosion resistance, compression resistance and strength to ensure that qualified products are produced by the original factory.

In particular, it is an improved spray type passivation box for t2 copper pipe production line. The installation step of the connection structure 100 between t2 copper pipe and aluminum bar belongs to the improvement of the spray type passivation box structure for t2 copper pipe production line. The passivation solution spray box is set above the side of the passivation solution box, the passivation solution spray box with downward sloping bottom is connected with the inlet of the passivation solution box by the outlet set on the box wall at the bottom of the inclined bottom, the inlet of the passivation solution box is located on the box wall above the passivation solution box the upper side of the passivation solution box is installed with a passivation pump, and the inlet pipe of the passivation pump is connected with the passivation solution box, The outlet pipe of the passivation pump is connected with the upper port of the passivation liquid spray box. With reasonable structure and convenient operation, it is convenient for operators to add passivation liquid to the passivation box, clean colloidal crystals at the bottom of the passivation box, avoid equipment blockage, avoid crystals adhering to the zinc layer on the surface of galvanized pipe, and improve the surface quality of galvanized steel pipe.

Today, the price of tube billets is up and down. At present, Jiangxin hot rolling is 3700 yuan, continuous casting 3600 yuan is down 100 yuan, Dongfang hot rolling 4020 yuan is down 30 yuan, Luli hot rolling 3670 yuan is down 50 yuan, Tiangang hot rolling 3830 yuan is down 50 yuan,Bellas304 stainless steel plate, production is stopped in mid January, Weigang hot rolling 3740 yuan is up 150 yuan, continuous casting 3590 yuan is up 90 yuan, Huaigang 4150 yuan is up 50 yuan, Zhongtian 4100 yuan, Changqiang 4050 yuan, Linggang 4140 yuan.

Copper tube has good bearing capacity. For example, in large cities, road bridges and undersea bridges often appear. Most road bridges are built with plastic coated copper pipes. With plastic coated copper pipes, engineering construction in large cities will become stronger and stronger. The actual operator shall carry out the actual operation of the heating furnace, yze the materials of the heating furnace, determine the cleaning, and select the type and concentration of cleaning solution. Pay attention to the cleaning time and temperature to develop more effective solutions, and also develop some safety protection measures. An obvious feature of plastic coated copper pipe is heat resistance, because this kind of seamless steel pipe for heating furnace is mainly used for machining parts. Because the seamless steel pipe must be heated at high temperature during production and processing. What are the plastic coated copper tubes to prevent wear. What are the plastic coated copper tubes to prevent wear. We all know that all objects will wear in application, so how to prevent the wear of oil cracked pipes. Now let's introduce it to you. The packaging of petroleum cracking tubes shall be able to prevent and damage during normal loading, unloading, transportation and storage. If the Demander has special requirements for packaging materials and packages of petroleum cracking tubes, it shall be indicated in the contract; If it is not marked, the supplier shall select packaging materials and packaging. Packaging materials shall comply with relevant requirements. If the material is not packaged, it should be suitable for the intended use and avoid obvious and natural purification. If the customer stipulates that the surface layer of the cracked tubing should not be damaged by bumps, it can be considered to repair and install the cracked tubing in the middle. Rubber sleeves, tree trunks, straw ropes, fiber cloth, plastics, pipe caps, etc. can be used for maintenance and installation. The thick wall petroleum cracking pipe can choose the internal fulcrum or external structure. Because thick walled tubes are thin. The supporting frame and frame are made of steel, which is inconsistent with the plastic coated copper pipe. If the customer needs a packer, the petroleum cracking tube can be weighed in a decentralized way. However, the specification must be 159MM500MM.

High quality and low price.Use the medical copper tube table to eat. Because of the unique of the medical copper tube, when the oil drops on the table, it will only stick to the table, but not penetrate the table. Only with a slight wipe of the rag, the oil stains will be easily disappeared. In this case, when cleaning large canteens, the liquidators do not need to spend much effort but are relaxed. They just need to prepare a rag and a basin of clean water, and then carefully scrub it. t2 Medical Copper Tube Company thinks that the medical copper tube table is only made of the surface of the medical copper tube, and its exterior is not made of the medical copper tube. The price is cheaper than the wooden table, which is extremely suitable for a small amount of purchase. The medical copper tube has a natural bright and beautiful feeling. The color is extremely blended and can stop the very good embellishment and reaction with the color in the surrounding situations. Now, let's understand some STEPs of the appearance processing of medical copper tubes. There are about five different methods for the appearance processing of medical copper tubes. Connect to t2 Medical Copper Tube Company and introduce them to the master. In addition, the following STEPs should be followed. First, before processing, the agreement should be stopped with the manufacturer, when using it, we should guarantee that the coils of the base we choose to use and the coils that are not yet used are the third of the same model and batch. If they are used in some construction, such as elevators, we should pay attention to the unexpected selection of materials. In some places with extraordinary contrast, it is not appropriate to use the mirror t2 medical copper tubes. When processing, it is necessary to select the appropriate manufacturing process, such as weld grinding, pay attention to the bias, which is also called unidirectionality. For example if the lines used are vertical rather than horizontal, it is not easy to apply the dirty residue on the appearance of t2 medical copper tubes. It is extremely easy when they are clean. When finishing, STEP of the process used should be added, so the cost also needs to be added. Therefore, when selecting the appearance of the processing, t2 Medical Copper Tube Company revealed that Panbo consumers should carefully select according to the situation, and when selecting the planning and design staff, they should have a full understanding of the appearance of t2 Medical Copper Tube. Since the birth of medical copper tube, it has been widely used in food, chemical industry, crude oil machine manufacturing and other industries for its superior . It is precisely because of this kind of universal needs that people are increasingly demanding for medical copper tubes. Although this kind of situation is basically conducive to the development of the medical copper tube industry. Having said so much, the editor of this website will introduce the most popular technology in the medical copper tube industry -- the medical copper tube appearance fingerprint free disposal punishment technology. Mentioned here, I believe that many enemies have learned the greatest advantages of this kind of technology from the name. However, do you know that this is nothing more than a contrast of significant and abstract advantages. The most one-sided introduction is also my face. The medical copper tube after adopting this kind of technical treatment has a smooth appearance and soft hand feeling, and ordinary dust and impurities are not easy to adhere. Therefore, it is also extremely easy to clean. If the ordinary dust is probably dirt, just wipe it with a wet rag and you will lose the clean and smooth appearance. Because the implementation of this kind of craft is to use electroplating oil to shine the film on the red interior line, so it has the characteristics of being tough and not easily scratched. This prevents the possibility that some slight bumps may damage the medical copper tube. It also allows the medical copper tube to be used twice as quickly. Stop the fingerprint free disposal and punish the medical copper tube after the accident. It also loses great promotion in appearance. As the saying goes, a superior appearance can always leave the best impression. Therefore, compared with the medical copper tube after the punishment and the medical copper tube without the punishment, it can often be welcomed by customers and enemies.Hot rolling and hot expansion. The main processing procedures include the blank sawing process, and the production process of the air conditioning copper pipe in the tower mainly includes cold drawing. Ring furnace heating process, piercing process, pipe rolling process, sizing process, cooling bed process, straightening process, pipe cutting soot blowing process, magnetic flux leakage detection process, surface inspection, length measurement and weighing to packaging and warehousing. Key points: yield strength limit: when the external force borne by the air conditioning copper tube sample exceeds the elastic limit of the material, although the stress no longer increases, the sample still has obvious plastic deformation. This phenomenon is called yield, that is, when the material bears an external force to a certain extent, its deformation is no longer in direct proportion to the external force, resulting in obvious plastic deformation. The stress when the air conditioning copper pipe yields is called the yield strength limit, and the corresponding S point in the tensile test curve is called the yield point. For air conditioning copper pipes with high plasticity, there will be an obvious yield point on the tensile curve, while for materials with low plasticity, there will be no obvious yield point, so it is difficult to calculate the yield limit according to the external force at the yield point. Therefore, in the tensile test method, it is usually specified that the stress when the gauge length on the specimen produces 0.2% plastic deformation is taken as the conditional yield limit, expressed as 0. The yield limit index can be used as the design basis for requiring that the parts do not produce obvious plastic deformation during operation.

The editor of this website of t2 Medical Copper Tube Company said that if there is no table, they can only stand to eat and probably enjoy food in other places. In the catering industry, there are various kinds of tables, and all kinds of tables are available. There are wooden tables and medical copper controlled tables. This table controlled by red copper in Chinese medicine is most common in large canteens such as schools, medical copper tubes have the ability to prevent rust. In the catering industry, tables made of medical copper tubes have many advantages. Next, the teacher of Medical Copper Tube Consumption Co., Ltd. will introduce you to the master. The medical copper tube table is easy to see in the large canteen. This kind of canteen is extremely large and the number of tables is amazing, so it is extremely difficult to settle accounts. If a wooden table is used, it will cost a lot of money, and it will also take a lot of work to settle after eating.

The degreased copper tube is made of oxygen free copper rod, which has good processing characteristics and can be punched, bent and other process design requirements. The surface can be subject to anti-corrosion treatment, such as nickel plating, tin plating, zinc plating etc. The surface anti-corrosion can reach 72 hours of fog test. The surface tin plating is environment-friendly lead-free tin,BellasCopper strip, and the surface tin layer supports soldering. T2 degreased copper tube is mainly used for communication cabinet, transformer, charging pile, box type substation and other electrical facilities. The copper bar is harder than the plastic pipe and has the degree of common metal (the strength of the cold drawn degreased copper pipe is equivalent to that of the steel pipe with the same wall thickness). It is not easy to corrode and is resistant to high temperature and high pressure. It can be used in various applications. The main material of copper bar is copper. The melting point of copper is as high as 1083 ℃, and the temperature of hot water can be ignored for degreased copper pipe, there is no need to worry about safety. When choosing to decorate the house, few people ask about the water supply pipe of the house. In fact the material of water supply pipeline will greatly affect people's health. T2 copper tube has strong capacity. Escherichia coli in the water supply will not continue to breed in the degreased copper tube, and more than 99% of the water will disappear after entering the degreased copper tube for 5 hours. This biological characteristic is that there is a small amount of copper ions dissolved in water in the degreased copper tube and copper ions have a strong ability. Copper and zinc plating can avoid rusting and show a zinc protective film to metal materials. The conductive metal material repair and color enhancement care agent I can generate the thickness of the metal material epoxy protection layer and the pipeline cathodic protection layer, the melting of metal tin and copper will produce aluminum alloy, which will improve the adhesion of copper strip coating. In addition the conductivity of metal tin is good. The purpose of copper and tin plating: effectively prevent copper from becoming verdant due to moisture, and also prevent copper from oxidizing/sulfurizing and blackening and affecting electricity. The service life of the tinned copper tube is several times or even more than ten times, marine climate or cold air is easy to turn black or produce copper green when oxidized, the copper bar surface shall be tinned for the total area the resistance and conductivity of the steel bar lap surface.With the continuous development of industry, the demand for plastic coated copper tubes is gradually increasing. Then how to apply wood grain paint on alloy pipes. Wood like paint is a kind of wood like paint. It is used for spraying plastic coated copper pipe and its process flow. Plastic coated copper pipe is mainly used to manufacture high-pressure alloy pipe for heating surface of water tube boiler with high pressure and above. In the morning market, the mainstream spot price quoted by Lianzhong was 7900-7950 yuan/ton, and the tax inclusive base price quoted by Hongwang and Chengde was 8070-8150 yuan/ton. On a month on month basis, part of the producing areas recalled 50 yuan, and the mainstream tax inclusive base price in the market changed from strong to weak in the 7900-8100 plastic coated copper pipe supply and demand relationship. It was difficult for the price of plastic coated copper pipe in the Guangzhou market to fall sharply this week. Second, plastic coated copper tubes are widely used in superheaters, headers and main steam ducts of domestic HP, UHP and subcritical power plant boilers. Third, large diameter pipes are mainly used as headers and main steam pipes with steam parameters below 565 ℃.

Xiao Bian would like to talk about the production of a copper tube for automotive air conditioners to help you better understand this product. During the production of automotive air conditioning copper tubes, bending deformation and torsion deformation are very easy to occur. Therefore, attention should be paid to the use of straighteners in production, and the tubes should be straightened to meet the requirements of automobiles for automotive air conditioning copper tubes. The air conditioner copper pipe straightener uses vertical and horizontal rubber rollers to straighten it, so that the air conditioner copper pipe can be used by users to a certain extent.Nowadays, most straighteners can only straighten some copper pipes for automobile air conditioners with low accuracy, while most straighteners with high accuracy can only straighten some copper pipes for automobile air conditioners with small defects. Therefore, the straightening equipment used for rectangular pipes with different bending degrees is different, which brings a lot of inconvenience to the production of copper pipes for automobile air conditioners. Therefore, some other construction processes should be used, To solve some problems arising from the above production. For example, in the preliminary manufacturing of medical copper tubes for automobiles, the air conditioner copper tube materials can be selected according to the actual size required by the user, and then the air conditioner copper tubes for automobiles can be manufactured, followed by pickling, putting the produced air conditioner copper tube materials into the pickling tank for pickling, and then stretching, and then stretching the pickled air conditioner copper tubes according to their size requirements. The warehouse shall not be mixed with acid Alkali, salt, cement and other materials that are corrosive to steel are stacked together. Air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel. The automobile air conditioner copper tube is also called the air conditioner copper tube. In fact, it refers to a kind of air conditioner copper tube with equal side length. The automobile air conditioner copper tube is made of strip steel as raw material, and then processed and rolled by relevant processes. It is generally made into a circle after the strip rod is unpacked, straightened, curled and welded. Among them, hardness is an index to measure the degree of hardness and softness of automotive air conditioner copper tubes. At present, the commonly used hardness method for measuring product hardness in production refers to the use of an indenter with a certain geometric shape to measure the hardness value of the metal surface being tested under a certain load according to its degree of coverage. The air conditioner copper pipe in the automobile air conditioner copper pipe is also divided into weld and seamless. Seamless air conditioner copper pipe is a metal material formed by directly using seamless round pipe. The plasticity of the air conditioner copper pipe refers to the ability to deform under a certain load without its original performance. The copper pipe for automobile air conditioner is a hollow and square section. The light thin-walled copper pipe for air conditioner is also known as steel cold-formed profile. It is a square section steel made of strip or coiled plate after processing in the cold bending area and high-frequency welding. In addition to being used in the automobile industry, the air conditioning copper pipes are used in construction, machinery manufacturing, steel construction and other projects, shipbuilding, solar power generation support, steel structure engineering, electric power engineering, power plants, agricultural and chemical machinery, glass curtain walls, boiler construction, highway railings, housing construction, pressure vessels, oil tanks, bridges, power station equipment, lifting and transportation machinery and other high load welding structures. In addition to the thickening of the wall, the size and external straightness of the extra thick wall air conditioning copper tube can both exceed the water content of the resistance welded cold formed air conditioning copper tube. Therefore, this kind of automobile air conditioning copper tube has better comprehensive mechanical properties and has the advantages of hot processing, cold processing, weldability and corrosion resistance.

Quality inspection report.What problems should we pay attention to in each production. It is a key process to weld copper pipe with correct process. Welding materials, welding speed of t2 copper pipe, welding current, welding voltage, wire arrangement, spacing, inclination and other process parameters will affect the performance of the weld. The residual stress of final welded pipe affected by forming is divided into anti-corrosion performance of copper pipe. Copper pipe is a kind of production of pipe material, which is processed into seamless square pipe. The physical properties of copper tubes are slightly weaker than those of hot-rolled steel tubes. The copper tube adopts a two-step push tube expanding machine, which integrates cone die tube expansion, data medium frequency induction heating and hydraulic press. With effective processing technology, low energy consumption, less infrastructure construction, good products, wide application fields of raw materials and products, and what are the production batches suitable for copper tube testing. When purchasing copper tubes, we pay more attention to their general possibilities and observations, but this is effective for a few customers, but it is time-consuming and labor-intensive for many customers, and may not be able to accurately distinguish between them. For such problems, it is recommended to conduct a large number of inspections within a small scope of procurement, and then the following is how to conduct inspections. The dimension tolerance of the cleanliness and wall thickness of the inner cavity of the copper tube is strict. However,Bellas7075 aluminum pipe, in the whole process of electric welding, due to the role of the molten metal material of the air conditioning copper pipe, the thickness of the pipe at the welding point will be uneven, and the inside and outside of the welding will be uneven. This will cause energy consumption of the conveyor. At this time, the internal welding ground must be used for leveling. Next, we will take you to the production process of copper pipe - internal welding and calibration. At present, many materials are also used in the life of red copper pipes. Be as judgmental as possible when buying. In fact, there are many things to pay attention to when purchasing copper tubes. Want to keep high when buying. What should we pay attention to when buying copper tubes next. The daily use and market are calculated according to the weight, so you should decide how much to use before buying.

In terms of output, although the steel output remained high in August, the steel plant maintenance began to increase from September. In addition to the possible production restriction policy held at the 19th National Congress and the off peak production policy in the heating season, the steel output will gradually decrease from September. In addition, in terms of demand, the overall investment in infrastructure and real estate development will remain at a relatively high level this year, and there is little possibility of a sharp decline. Therefore, industry ysts believe that downstream demand for steel, especially construction steel, will be more stable.

Handle carefully to prevent damage and scratches. 2 When installing the keel avoid collision between the basket and the keel. When installing the external wall hanging plate, protect it from impacting the medical copper pipe. 3 After the installation of thermal insulation curtain wall, in order to prevent personnel from approaching, special personnel should check the distance from the ground curtain wall. 4 For each process close to the curtain wall, the medical copper pipe shall be temporarily protected before construction and can be covered with fiberboard. Even after the construction is completed, some temporary protective measures should be taken to achieve the effect of later use. 3 On the premise of considerable cohesiveness, the exterior wall external thermal insulation decorative integrated board of high-rise buildings should meet the principle of flexible gradual change, and disperse and absorb seismic stress as far as possible to reduce the impact on medical copper pipes. 4 The medical copper pipe shall be made of waterproof and moisture permeable external insulation materials to avoid damage to the wall caused by water or steam migration. 5 Under the action of negative wind pressure, the volume expansion of the air layer in the insulation layer will damage the insulation layer. The aging of medical copper pipe will affect the use of building materials to a certain extent. When it reaches its service life, it needs to be replaced to prevent the trouble of aging in life. 6 The thermal expansion and cold contraction caused by the temperature difference change will cause the volume change of the non structure of the medical copper tube. Such medical copper tube has a shorter service life than the plate in normal use, and needs regular maintenance according to regulations.

Bellas.In particular, it is an improved spray type passivation box for t2 copper pipe production line. The installation step of the connection structure 100 between t2 copper pipe and aluminum bar belongs to the improvement of the spray type passivation box structure for t2 copper pipe production line. The passivation solution spray box is set above the side of the passivation solution box, the inlet of the passivation solution box is located on the box wall above the passivation solution box, the upper side of the passivation solution box is installed with a passivation pump, The outlet pipe of the passivation pump is connected with the upper port of the passivation liquid spray box. With reasonable structure and convenient operation, it is convenient for operators to add passivation liquid to the passivation box, clean colloidal crystals at the bottom of the passivation box avoid equipment blockage, avoid crystals adhering to the zinc layer on the surface of galvanized pipe, and improve the surface quality of galvanized steel pipe.

The utility model relates to a connecting structure, in particular to a connecting structure of a copper tube and an aluminum row. At present, most of the copper aluminum transition joints have not been effectively protected. In this way, under the condition of long-time electrification and heating and affected by the water vapor or corrosive gas in the air, resulting in the reduction of the effective contact area of the connection point, the increase of the contact resistance and the excessive heating or even burning of the connection point.

The copper tube warehouse of automobile air conditioner shall not be stacked with acid, alkali, salt, cement and other materials that are corrosive to steel. The air conditioning copper pipe is based on carbon structural steel. The phenomenon of torsional deformation of the air conditioning copper pipe requires weeds and all sundries on the site. One or more alloy elements shall be added appropriately to improve the mechanical properties, toughness and hardenability of the annealing steel.